Accessories..................................... 9 OVERVIEW OF COMPONENTS ........................10 ZIRCON MINI ..................................10 ZIRCON 2GR ..................................11 ZIRCON DISPLAY CONTROL 3GR ..........................12 DIMENSION SKETCH ............................13 ZIRCON MINI CONTROL ............................. 13 ZIRCON DISPLAY CONTROL 2GR ..........................14 ZIRCON DISPLAY CONTROL 3GR ..........................15 TRANSPORT ................................16...
Page 3
ZIRCON CONTENTS OPERATION ................................20 Espresso brewing ................................20 Steaming and frothing milk ..............................21 Hot water dispensing ................................. 22 ESPRESSO MACHINE WITH BUILT-IN GRINDER ................23 Operations before starting up the coffee grinder ....................... 23 How to obtain a grinded coffee dose ..........................23 Adjusting the grinding coarseness ...........................
ZIRCON SYMBOL DESCRIPTION Hazard intensity levels There are three different levels of hazard intensity, identified by signal words DANGER, WARNING and IMPORTANT. The level of hazard is determined by the following definitions. Observe the statements to ensure safety, performance, prevent injury and machine damage.
ZIRCON GENERAL Introduction Thank you for choosing the ZIRCON espresso machine. We hope you enjoy it ! Read the user manual before using the machine. Keep this manual close to hand for future This manual contains important instructions on reference. If damaged or lost, request a copy intended and safe use of the coffee machine.
ZIRCON GENERAL In case of emergency, (e.g. the machine catches to three units of the same model. Do not place fire or becomes unusually hot or noisy), other heavier packages on top of the box. disconnect the power immediately and close The machine is likely to be exposed to the water inlet tap.
TECHNICAL SPECIFICATIONS ZIRCON ZIRCON MINI MODEL SPECIFICATIONS MINI CONTROL MINI GRINDER MINI 2GR Steam wand 1 unit Hot water outlet 1 unit Temperature control Pressure switch Temperature control by group Programmed via display Dispensing system for tall cups Optional Energy saving mode...
TECHNICAL SPECIFICATIONS ZIRCON ZIRCON 2GR MODEL SPECIFICATIONS 2GR CONTROL 2GR PULSER 2GR DISPLAY Steam wand 1 units 2 units Hot water outlet 1 unit 1 unit Temperature control Pressure switch PID regulation Temperature control by group Programmed via display Dispensing system for tall cups...
TECHNICAL SPECIFICATIONS ZIRCON ZIRCON 3GR MODEL SPECIFICATIONS 3GR CONTROL 3GR DISPLAY Steam wand 2 units Hot water outlet 1 unit Temperature control Pressure switch PID regulation Temperature control by group Programmed via display Dispensing system for tall cups Optional Energy saving mode...
ZIRCON OVERVIEW OF COMPONENTS Front view of the machine ZIRCON MINI ON/OFF switch Drink buttons Hot water tap Steam tap Hot water outlet Steam wand Heater element lamp Porta-filter Boiler pressure gauge Brewing group...
ZIRCON OVERVIEW OF COMPONENTS Front view of the machine ZIRCON 2GR Digital temperature control Drink buttons Hot water tap Steam tap ON/OFF switch Hot water outlet Heater element lamp Porta-filter Steam wand Brewing group...
ZIRCON OVERVIEW OF COMPONENTS Front view of the machine ZIRCON DISPLAY CONTROL 3GR Display ON/OFF switch Steam tap Drink buttons Steam tap Heater element Steam wand Porta-filter lamp Hot water outlet Brewing group Steam wand...
ZIRCON DIMENSION SKETCH ZIRCON MINI CONTROL Model ZIRCON MINI 1Gr 530 mm 460 mm 590 mm 74 mm ZIRCON MINI 1Gr Tall Cup 530 mm 460 mm 590 mm 124 mm ZIRCON MINI 2Gr 530 mm 460 mm 590 mm...
ZIRCON DIMENSION SKETCH ZIRCON DISPLAY CONTROL 2GR Model ZIRCON 2Gr 530 mm 680 mm 590 mm 74 mm ZIRCON 2Gr Tall Cup 530 mm 680 mm 590 mm 124 mm ZIRCON 2Gr 3 Boilers 530 mm 680 mm 590 mm...
ZIRCON DIMENSION SKETCH ZIRCON DISPLAY CONTROL 3GR Model ZIRCON 3GR 530 mm 980 mm 590 mm 74 mm ZIRCON 3GR Tall Cup 530 mm 980 mm 590 mm 124 mm ZIRCON 3Gr Boilers 530 mm 980 mm 590 mm 74 mm...
ZIRCON TRANSPORT Packaging The machine is shipped in a unique carton box which uses expanded polystyrene paddings. The machine box is provided with conventional symbols that can be perfectly visible during the handling and storage tasks. The machine box must stay in a vertical position during the transport. Do not tip or try to place the box tilted sideways in any way.
ZIRCON INSTALLATION Electrical installation The coffee machine should only be connected to the power supply by qualified personnel. The following safety instructions should be followed at all times: Check that the electrical specifications on the ratings plate match the specifications of the power supply at the point of installation.
ZIRCON INSTALLATION Water connection The Installation of the machine to a water mains connection must be done by a qualified person. Rinse around 20 liters of water from the main water supply before connecting the machine to the water connection.
ZIRCON INSTALLATION The porta-filter set Lock-in spring (filter basket) Filter basket Placing porta-filter spring Porta-filter and filter basket for single espresso (7g) Porta-filter & filter basket for double espresso (14g) Inserting the porta-filter in the group Align the porta-filter's two lateral Insert the porta-filter and rotate it anti-clockwise until flanges with the slots in the group.
ZIRCON OPERATION Espresso brewing Important: Always keep the porta-filter inserted in the group to keep it warm. This is very important to maintain an optimal temperature to get the best espresso. Unlock and remove the porta-filter Fill the filter basket of the from the group head.
ZIRCON OPERATION Steaming and frothing milk Steaming Frothing Place the steam wand over the drip tray Immerse the steam wand into the jug containing the and open the steam tap for a few seconds, milk, make sure the wand tip is submerged.
ZIRCON OPERATION Hot water dispensing Machines with manual water tap Place a jug (or similar) under the hot water outlet Open the hot water tap. Close the tap as soon as the machine has dispensed the desired amount of water.
ZIRCON ESPRESSO MACHINE WITH BUILT-IN GRINDER Operations before starting up the coffee grinder PART NAME Bean hopper lid Bean hopper Bean stop Grinding adjustment disk Dosage device lid Dosage device Grinder on/off switch Dosage lever Coffee tamper Ground coffee outlet Check that the bean hopper (2) is correctly fitted in place.
ZIRCON ESPRESSO MACHINE WITH BUILT-IN GRINDER Adjusting the grinding coarseness If you want to obtain finer grinded coffee: Turn the grinding adjustment disc(4) in a clockwise direction. If you want to obtain coarsely grinded coffee: Turn the grinding adjustment disc(4) in a counter-clockwise direction.
ZIRCON CLEANING AND MAINTENANCE Coffee machine cleaning Important: To obtain the best efficiency, quality and performance of the machine, you should always follow the cleaning and care instructions provided in this manual. Turn off the power switch when cleaning the exterior of the machine.
ZIRCON CLEANING AND MAINTENANCE Cleaning the Brewing group and porta-filter Unlock and remove the porta-filter from the group head. Place the cleaning membrane in the filter basket. Fill the filter basket with professional cleaning powder for espresso coffee machines. Lock the porta-filter into the group head.
ZIRCON CLEANING AND MAINTENANCE Cleaning the gasket and shower plate Cleaning the gasket When placing the porta-filter filled with grinded coffee into the brewing group, left overs will accumulate in the closing surface. If these remains are excessive it can prevent a good closing between the porta-filter and the group head.Moreover, these remains can even block the dispensing of water...
ZIRCON CLEANING AND MAINTENANCE Additional handling of the machine Important: Avoid placing wet cups directly on the cup shelf, it may drip into the machine and cause machine damage. Remove and insert the porta-filter gently. Never use excessive force to try to close the porta-filter.
ZIRCON PROGRAMMING Buttons functions Here is some of the additional functions that the electronics offers: Volume control of four different espresso drinks per brewing group. Time-controlled hot water dispensing. (if available) Automatic filling and level control of the boiler. Automatic switch off of the heating element if not enough water.
ZIRCON PROGRAMMING Programming the coffee dosage This section explains how to program the doses dispensed automatically by the drink buttons. Important: Use a porta-filter filled with fresh coffee for every new dose you program. On machines not equipped with a display, hold down the Continuous Dispensing button 4 seconds.
ZIRCON PROGRAMMING USING THE DISPLAY Machine status Machines equipped with a display include the following additional functions: Automatic daily on/off timer (stand-by function). Clock settings (current time and date). Promotional display. Number of coffees/infusions dispensed. Digital boiler-temperature display and control.
ZIRCON PROGRAMMING USING THE DISPLAY Accessing the second menu level With the machine ON, press the Continuous Dispensing button Doses setting Select within 30s the left-hand Drink buttons and hold it down (for over 8 seconds) until the dose-programming menu is displayed. All the Drink buttons lights fig.
ZIRCON PROGRAMMING USING THE DISPLAY Auto On/Off After accepting the changes made in the "Set clock" menu, pressing the 2 Auto On/Off Short Espressos button accesses the coffee machine's Auto On/Off hh.mm programming menu (see fig. 09). fig. 9 To change the Auto On/Off time, increase/decrease the values (hours)
ZIRCON MESSAGES AND ALARMS Flow meter Fault in flow meter X / Gr. X Flow fault detected in counter X Time-out alarm Check that the machine is receiving water. Boiler filling up Probe unconnect Temperature sensor fault Service the machine.
ZIRCON TROUBLESHOOTING The following checks can be carried out by users once the machine has been turned off and disconnected from the power supply. For all other non-specified machine faults, disconnect the machine from the power supply and immediately contact authorised and qualified service personnel.
Page 36
For the warranty to be valid the conditions for maintenance must have been followed according to our instructions, proper precaution has been made and warranty claim been issued without delay. The affected equipment may not be used during awaiting service if there is any risk that the damage or defect would worsen.
Need help?
Do you have a question about the ZIRCON and is the answer not in the manual?
Questions and answers