ORIGINAL OPERATING INSTRUCTIONS SF 22A / SFH 22A cordless drill / driver It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool.
Modification of the power tool or tampering with its parts is not permissible. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.
Grease lubrication 2.6 The items supplied include (toolbox versions): 1 Power tool 1 Side handle 1 Operating instructions 1 Hilti toolbox 2.7 The items supplied include (cardboard box versions): 1 Power tool 1 Side handle 1 Operating instructions 2.8 Additional items required for operating the tool B 22/2.6 LiIon or B 22⁄3.3 LiIon battery with C4⁄3690, C4⁄36350,...
Designation Short designation Charger for Li-ion batteries C 4/3690 Charger for Li-ion batteries C 4/36350 Battery B 22/3.3 LiIon Battery B 22/2.6 LiIon Battery B 22/1.6 LiIon Belt hook Designation Description Keyless chuck clamping range ∅ 1.5…13 mm Drilling diameter range in wood ∅...
Noise and vibration information (measured in accordance with EN 60745): Typical A-weighted sound 86 dB (A) power level for the SF 22-A Typical A-weighted sound 107 dB (A) power level for the SFH 22-A Typical A-weighted emission 75 dB (A) sound pressure level for the SF 22-A Typical A-weighted emission...
Page 10
(grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Page 11
To achieve a high level of dust collection, use a suitable vacuum cleaner of the type recommended by Hilti for wood dust and/or mineral dust together with this tool. Ensure that the workplace is well ventilated.
Page 12
Place the tool in a location where it can be kept under observation, well away from flammable materials, and allow it to cool down. Contact Hilti Service after the battery has been allowed to cool. 5.3.4 Electrical safety Before beginning work, check the working area (e.g.
6.2 Charging the battery DANGER Use only the Hilti batteries and Hilti chargers listed under “Accessories”. 6.2.1 Charging a new battery for the first time Charge the battery fully before using it for the first time.
6.4 Removing the battery 1. Press both battery release buttons. 2. Pull the battery out of the power tool toward the rear. 6.5 Fitting the side handle 1. Set the forward / reverse switch to the middle position (trans- port lock) or remove the battery from the power tool. 2.
Page 15
7.4 Switching on / off Speed of rotation can be controlled smoothly up to maximum speed by pressing the control switch slowly. 7.5 Fitting the drill bit 1. Set the forward / reverse switch to the middle position or remove the battery from the power tool. 2.
NOTE If use of the power tool continues, battery discharge is stopped automatically (indicated by LED 1 blinking) before the battery cells suffer damage. Charge the battery with the Hilti charger approved for use with Li-ion batteries. NOTE – A conditioning charge (as is required with NiCd or NiMH batteries) is not necessary.
If necessary, the power tool should be repaired by Hilti Service. 8.5 Checking the power tool after care and maintenance After carrying out care and maintenance work on the power tool, check that all protective and safety devices are fitted and that they function faultlessly.
For repair or replacement, send the tool or related parts immedi- ately upon discovery of the defect to the address of the local Hilti marketing organization provided. This constitutes Hilti’s entire obligation with regard to warranty and supersedes all prior or contemporaneous comments and oral or written agreements concerning warranties.
Page 19
Hilti Corporation, Feldkircherstrasse 100, FL9494 Schaan Paolo Luccini Jan Doongaji Head of BA Quality and Process Manage- Executive Vice President ment Business Area Electric Tools & Accessories Business Unit Power Tools & Accessories 01/2012 01/2012 Technical documentation filed at: Hilti Entwicklungsgesellschaft mbH...