Heat & Glo SL-750TRS-IPI-D Owner's Manual
  1. Manuals
  2. Brands
  3. Heat & Glo Manuals
  4. Indoor Fireplace
  5. SL-750TRS-IPI-D
  6. Owner's manual

Heat & Glo SL-750TRS-IPI-D Owner's Manual

Hide thumbs Also See for SL-750TRS-IPI-D:
Table of Contents

Advertisement

Quick Links

Models:
SL-750TRS-IPI-D
SL-550TRS-IPI-D
SL-350TRS-C
•
Important operating
and maintenance
instructions included.
WARNING: If the information in
these instructions is not followed ex-
actly, a
re or explosion may result
causing property damage, personal
injury, or death.
• Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the re department.
• Installation and service must be performed
by a quali ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in manu-
factured home (USA only) or mobile home and must be installed
in accordance with the manufacturer's instructions and the man-
ufactured home construction and safety standard, Title 24 CFR,
Part 3280 or Standard for Installation in Mobile Homes, CAN/
CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07
CAUTION
DO NOT DISCARD THIS MANUAL
Read, understand and follow
•
these instructions for safe
installation and operation.
Owner's Manual
•
Leave this manual with
party responsible for
use and operation.
WARNING
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Glass and other surfaces are hot during
operation and cool down.
• Keep children away.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high temperatures.
• Do NOT operate with protective barriers open or
removed.
• Keep clothing, furniture, draperies and other
combustibles away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the xed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber
or gas tter;
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
Installation and service of this appliance should be
performed by quali ed personnel. Hearth & Home
Technologies suggests NFI certi ed or factory-trained
professionals, or technicians supervised by an NFI
certi ed professional.
Installation and Operation
1

Advertisement

Table of Contents
loading

Related Manuals for Heat & Glo SL-750TRS-IPI-D

Summary of Contents for Heat & Glo SL-750TRS-IPI-D

  • Page 1 NFI This appliance is only for use with the type(s) of gas indicated on the rating plate. certi ed professional. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 2 Hearth & Home Technologies, Inc. Type of Gas 20802 Kensington Blvd., Lakeville, Mn 55044 Gas and Electric Information Model Number Serial Number Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 3: Table Of Contents

    D. Warranty ........... 78 Horizontal Termination Cap ......33 E. Contact Information ........79 D. Installing Roof Flashing and Vertical Termination Cap .......... 35 = Contains updated information. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 4: Listing And Code Approvals Section

    Heat & Glo Quality Systems burn, whether ame proofed or not, or whether plastered or registered by SGS ICS unplastered shall be considered combustible materials. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 5: Requirements For The Commonwealth Of Massachusetts

    (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL See Gas Connection section for additional Common- OBSTRUCTIONS”. wealth of Massachusetts requirements. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 6: Getting Started

    1/2 - 3/4 inch length, #6 or #8 Self-drilling screws Manometer Voltmeter Tape measure Noncorrosive leak check solution One 1/4 inch female connection (for optional fan). Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 7: Framing And Clearances A. Selecting Appliance Location

    68-1/4 16-1/4 Inches Installation SL-550TRS-IPI-D 1054 1492 1232 1734 Millimeters 39-3/8 55-5/8 46-3/8 65-1/8 16-1/4 Inches SL-350TRS-C 1000 1413 1178 1654 Millimeters Figure 3.1 Appliance Locations Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 8: Constructing The Appliance Chase

    8-5/8 38-1/4 27-1/2 16-1/4 Inches SL-750TRS-IPI-D 1067 Millimeters 8-5/8 27-1/2 16-1/4 Inches SL-550TRS-IPI-D Millimeters 8-5/8 27-1/2 16-1/4 Inches SL-350TRS-C Millimeters Figure 3.2 Clearances to Combustibles Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 9: Mantel Projections

    Clearances to Mantels or other Inches Combustibles above Appliance Millimeters Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 10: Termination Locations

    Horizontal distance between terminations 20 in. 24 in. min. Distance to perpendicular wall 18 in. 18 in. Vertical distance between terminations Figure 4.3 Multiple Vertical Termination Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 11 Figure 4.4 Minimum Clearances for Termination CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 12: Vent Information And Diagrams

    8.5 inches vertical run. A length of straight pipe is allowed between two 45 elbows (see Figure 5.1). Figure 5.2 DVP Pipe Effective Length Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 13: Use Of Flex Vent

    CLEARANCE clearance to combustibles. However, the vent attachment point and the restop location are considered to be supports. Figure 5.3 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 14: Vent Diagrams

    1.4 m 15 ft. 4.6 m 15 ft. 4.6 m H Maximum= 15 ft. (4.6 m) V + H Maximum= 40 ft. (12.2 m) Figure 5.4 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 15: Natural Gas

    1.4 m 14 ft. 4.3 m H + H1 Maximum= 14 ft. (4.3 m) V + H + H1 Maximum= 40 ft. (12.2 m) Figure 5.5 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 16 7 ft. 2.1 m 14 ft. 4.3 m 4.5 ft. 1.4 m 14 ft. 4.3 m 14 ft. 4.3 m Maximum=40 ft. (12.2 m) Figure 5.6 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 17: Side View

    2-1/4 in. self tapping screws provided. VIEW FROM UNDERNEATH BAFFLE FRONT OF UNIT FIREBOX BACK SIDE VIEW EXHAUST BAFFLE FIREBOX BACK Figure 5.7 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 18 2.4 m 5 ft. 1.5 m 15 ft 4.6 m H Maximum= 15 ft. (4.6 m) + H Maximum = 40 ft (12.2 m) Figure 5.8 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 19 1.8 m 4.5 ft 1.4 m 14 ft. 4.3 m H Maximum = 14 ft (4.3m) + H Maximum= 40 ft. (12.2 m) Figure 5.9 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 20 (see and out installation (see Figure 5.3 ). Figure 5.3 ). Figure 5.17 Figure 5.17 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 21 6.5 ft. 2.1 m 14 ft. 4.3 m H Maximum= 7.5 ft. (2.3 m) Maximum= 14 ft. (4.3 m) = 40 ft. (12.2 m) Figure 5.12 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 22 3 ft. 914 mm 7.5 ft. 2.3 m H Maximum= 7.5 FT (2.3 m) V + H + H Maximum= 40 FT (12.2m) Figure 5.14 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 23 3 ft. 914 mm 7 ft. 2.1 m 14.5 ft. 4.4 m H Maximum= 7.5 ft. (2.3 m) Maximum= 40 ft. (12.2 m) Figure 5.16 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 24: Vent Clearances And Framing

    Figure 6.2 Horizontal Venting Clearances to Combustible Materials inch greater than the pipe is acceptable. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 25: Vertical Penetration Framing

    • Field construct additional shield height if insulation is deeper than height of attic ATTIC SHIELD INSTALLED ATTIC SHIELD INSTALLED shield. ABOVE CEILING BELOW CEILING Figure 6.5 Installing the Attic Shield Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 26: Appliance Preparation

    Remove the white gasket material covering For rear venting there is no insulation in the outer vent pipe. Figure 7.3 the seal cap. Replace the top heat shield. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 27: Rear Vent

    Slide the insulation gasket onto the vent section, Cut the metal retaining band and fold the Figure 7.7 up against the appliance and over the tabs. sides out. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 28: Securing And Leveling The Appliance

    NOTE: Once appliance is setup for top or rear venting, Failure to keep insulation, framing or other material away it CANNOT be changed at a later time. from the appliance may cause re. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 29: Installing Vent Pipe

    Use screws no longer than 1 inch. If predrilling screw holes, do NOT penetrate inner pipe. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 30 If the slip section is too long, the inner and outer ues of the slip section can be cut to the desired length. Figure 8.7 Screws into Slip Section Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 31: Disassembly Of Vent Sections

    • Do NOT allow vent to sag below connection point to appliance. Improper support may allow vent to sag or separate. Figure 8.11 Align and Disassemble Vent Sections Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 32 Improper support may allow vent to sag or separate. preceding component, attach with a minimum of two (2) sheet metal screws. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 33: Installing Heat Shield And Horizontal Termination Cap

    (pipe section) to properly space it from available. the pipe section (see Figure 8.12). When penetrating a brick wall, a brick extension kit is available for framing the brick. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 34 SHIELD IF TOO LONG, ADD TO SHIELD IF TOO SHORT WALL SHIELD FIRESTOP (EXTERIOR) WALLSHIELD FIRESTOP (INTERIOR) Figure 8.15 Heat Shield, Interior & Exterior Firestops Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 35: Installing Roof Flashing And Vertical Termination Cap

    Inspect external vent cap regularly. • Ensure no debris blocks cap. • Combustible materials blocking cap may ignite. • Restricted air ow affects burner operation. Figure 8.18 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 36 Slide the assembled storm collar down the pipe section until it rests on the roof ashing. Caulk around the top of the storm collar (see Figure 8.17). Figure 8.19 Assembling the Storm Collar Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 37: Gas Information

    5.0 inches 11.0 inches Inlet Pressure w.c. w.c. Maximum Inlet 14.0 inches 14.0 inches Gas Pressure w.c. w.c. Manifold 3.5 inches 10.0 inches Pressure w.c. w.c. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 38 Do NOT change the valve settings. • This valve has been preset at the factory. • Changing valve settings may result in re hazard or bodily injury. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 39: Electrical Information

    • Wire must have high temperature insulation. ual thermostat instructions) to ensure proper operation of appliance. PIEZO PILOT THERMOSTAT WIRE ASSEMBLY THERMOCOUPLE VALVE Figure 10.1 Standing Pilot Ignition Wiring Diagram Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 40: Intelli Re Ignition System Wiring

    IGNITION MODULE 3 VAC INTERMITTENT PILOT IGNITOR TRANSFORMER WHITE 3 VAC ORANGE GROUND TO FIREPLACE PLUG IN CHASSIS JUMPER WIRE BATTERY PACK (TO BROWN) THERMOSTAT WIRE ASSEMBLY VALVE Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 41: Junction Box Installation

    Figure 10.4 Junction Box Wired to Wall Switch face of the junction box, and connect to the top fan switch connector (1/4 inch male) as shown. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 42: Finishing

    Seal joints between the nished wall and appliance top • Operation of louvers or doors. and sides using only a 300 F minimum sealant. • Access for service. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 43: Appliance Setup

    Do NOT place on burner top. • Save the remaining ember materials for use during appli- ance servicing. The embers provided should be enough for 3 to 5 applications. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 44: Install Refractory

    Figure 1. REFRACTORY REFRACTORY RETAINER TAB RETAINER TAB Figure 3. Figure 3. Figure 3. Figure 3. Step 4. Install logs according to the install manual. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 45: Positioning The Logs

    “forked” end of the log straddling the far right grate bar. 541-935B 8/00 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 46 LOG #5 (SRV530-703): Position log #5 (“burned-out” section facing right) so that the bottom is centered and rests up against the 1st grate bar and the top is leaning into the indent of log #1. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 47 LOG #2 (SRV2065-703) Place log #2 on the grate bar and push it back against the refractory. The pilot should be centered within the large notch on log #2. 2065-935 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 48 LOG #5 (SRV2065-701) Place log #5 on log #2. The front left of the log will rest on log #4. Log 5 must be pushed back against refractory. See Figure 3. Figure 3. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 49 LOG #2 (SRV2066-703) Place log #2 on the grate bar and push it back against refractory. The pilot should be centered within the large notch on log #2. 2066-935 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 50 LOG #5 (SRV2065-701) Place log #5 on log #2. The Figure 3. front left of the log will rest on log #4. Log #5 must be pushed back against refractory. See Figure 3. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 51: Glass Assembly

    1/2” open 1/2” open SL-550TRSIPILPD Fixed Fixed SL-750TRS-IPI-D 1/2” open 1/2” open SL-750TRSLPIPID Fixed Fixed LATCHES (BOTH BOTTOM AND TOP) GLASS ASSEMBLY Figure 12.8 Glass Assembly Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 52: Operating Instructions

    Immediately call a quali ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 53: To Turn Off

    For additional information on operating your Hearth & Home Technologies replace, please refer to www. replaces.com. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 54: For Your Safety

    For additional information on operating your wise to OFF”. Do not force. Hearth & Home Technologies replace, please refer to www. replaces.com. 5. Close control access panel. 464-903G Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 55: After Appliance Is Lit

    In an Intelli re ignition system it is normal to see the pilot ame, but it should turn off when ON/OFF is turned off. In a standing pilot system the pilot will always stay on. continually? Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 56: Troubleshooting

    Take a reading at the thermopile leads. The read- ing should be 325 millivolts minimum. Replace the thermopile if the reading is below the minimum. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 57 Ensure that the glass is tightened properly on the unit, particularly on top corners. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 58: Intelli Re Ignition System

    A wrong ori ce or too high an inlet pressure can cause pilot ame to lift. The sensor rod may be contaminated. Clean sensor rod with emery cloth. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 59 Module voltage output / Valve/Pilot Verify battery voltage is at least 2.7 volts. Replace batter- solenoid ohms readings. ies if voltage is below 2.7. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 60: Maintaining And Servicing Appliance

    • Restricted air ow affects burner operation. control compartment • Burner, burner ports Risk of: • Fire • Delayed ignition or explosion • Exposure to combustion fumes • Odors Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 61 2. Replace batteries in remote transmitters and battery-powered receivers. 3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure or leaking. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 62: Reference Materials

    Millimeters Inches Millimeters 1041 8-3/4 36-1/8 16-1/4 35-5/8 30-3/4 21-5/8 15-3/8 34-1/2 15-7/8 3-9/16 6-5/8 6-7/8 33-5/8 26-7/8 2-1/4 37-7/8 1016 Figure 16.1 Appliance Dimensions-SL-750TRS-IPI-D Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 63 Inches Millimeters Location Inches Millimeters 31-1/8 8-3/4 32--1/8 16-1/4 27-1/8 25-3/4 12-7/8 3-1/2 15-7/8 6-7/8 6-5/8 23-3/8 30-1/8 32-9/16 2-1/8 35-1/2 Figure 16.2 Appliance Dimensions-SL-550TRS-IPI-D Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 64 Inches Millimeters Location Inches Millimeters 8-3/4 28-1/8 16-1/4 30-1/8 24-1/8 22-3/4 11-3/8 28-1/8 15-7/8 3-1/2 6-5/8 6-7/8 21-3/8 2-1/8 30-5/8 34-1/2 Figure 16.3 Appliance Dimensions-SL-350TRS-C Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 65: Vent Components Diagrams

    (356 mm) 5 in. 12 in. (127 mm) (305 mm) 6 in. (152 mm) DVP-HVS (Vent Support) DVP-WS (Wall Shield Firestop) Figure 16.4 DVP vent components Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 66 6-3/4 in. (171 mm) 10-5/8 in. (270 mm) 12 in. Effective (305 mm) Length DVP-TRAP Horizontal Termination Cap DVP-TRAP1 DVP-TRAPK1 DVP-TRAP2 DVP-TRAPK2 DVP-HPC1 DVP-HPCK1-B DVP-HPC2 DVP-HPCK2-B Figure 16.5 DVP vent components Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 67 COOL-ADD Cap Shield 13-7/8 in. 9-1/2 in. (352 mm) (241 mm) 14 in. (356 mm) DVP-TRAPFL Flashing DRC-RADIUS Cap Shield Figure 16.6 DVP vent components Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 68 7-3/4 to 10-3/8 in. (197 to 264 mm) 1-5/8 in. (41 mm) DVP-FBHT Fire Brick Termination Cap DVP-HPC High Performance Cap Figure 16.7 DVP vent components Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...
  • Page 69 H when using the snorkel cap except when using the simple up and out installation. WALL BRACKET (SL- SERIES) SL Series Vent Components Figure 16.8 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 70: Service Parts

    Product. HEARTH & HOME TECHNOLOGIES also reserves the right to discontinue styles and products. © 2005 Hearth & Home Technologies Inc. Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL-350TRS-C • InD • 2065-985 Rev. o • 3/07...

  • Page 71: Contact Information

    6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending. Printed in U.S.A. - Copyright 2006 Heat & Glo • SL-750TRS-IPI-D, SL-550TRS-IPI-D, SL350TRS-C • InD • 2065-985 Rev. o • 3/07...

This manual is also suitable for:

Sl-350trs-cSl-550trs-ipi-d

Table of Contents