1. Manuals
  2. Brands
  3. Heat & Glo Manuals
  4. Indoor Fireplace
  5. SL-350TRS-D
  6. Owner's manual

Heat & Glo SL-350TRS-D Owner's Manual

Hearth and home technologies fireplace owner's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Models:
SL-750TRS-IPI-E
SL-550TRS-IPI-E
SL-350TRS-D
SL-350TRS-IPI
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07
CAUTION
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Owner's Manual
Installation and Operation
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Glass and other surfaces are hot during
operation and cool down.
• Keep children away.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high temperatures.
• Do NOT operate with protective barriers open or
removed.
• Keep clothing, furniture, draperies and other combustibles
away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber
or gas fi tter;
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
1

Advertisement

Table of Contents
loading

Related Manuals for Heat & Glo SL-350TRS-D

Summary of Contents for Heat & Glo SL-350TRS-D

  • Page 1 CAN/CSA Z240MH. This appliance is only for use with the type(s) of gas indicated on the rating plate. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 CAUTION DO NOT DISCARD THIS MANUAL • Read, understand and follow these instructions for safe installation and operation.
  • Page 2 MIN. INPUT INPUT BTUH: ORIFICE SIZE: ORIFICE Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Congratulations This Owner’s Manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

  • Page 3: Table Of Contents

    Termination Cap (SL Pipe) ......35 F. Installing Roof Flashing and Vertical Termination Cap . . . 36 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Table of Contents 9 Gas Information A.

  • Page 4: Listing And Code Approvals

    Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in Canada. Heat & Glo Quality Systems registered by SGS ICS Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 C. BTU Specifi cations Models Maximum U.S.

  • Page 5: Requirements For The Commonwealth Of Massachusetts

    (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB- STRUCTIONS”. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Inspection The state or local gas inspector of the side wall horizon-...

  • Page 6: Getting Started

    Tape measure Noncorrosive leak check solution One 1/4 inch female connection (for optional fan). Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 C. Inspect Appliance and Components WARNING Inspect appliance and components for damage.

  • Page 7: Framing And Clearances

    1511 39-1/2 55-7/8 SL-350TRS-D 1003 1413 Figure 3.1 Appliance Locations Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 NOTE: For actual appliance dimensions refer to Sec- tion 16. Min. Min. 45-1/2 1155 See Section...

  • Page 8: Constructing The Appliance Chase

    * Dimension when rear venting with one 90º elbow Figure 3.2 Clearances to Combustibles Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to pre- vent conducting cold up into the room.

  • Page 9: Elevated Hearth Systems

    NOTE 2. Verify Marble Cut Lengths on site prior to cutting. NOTE 3. Dimensions assume use of a 3/4 in. Hearth Pad. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 ELEVATED APPLIANCE PART #...

  • Page 10: Mantel Projections

    3-1/2 in. 1/2 in. NON-COMBUSTIBLE ZONE Figure 3.4 Non-Combustible Zone Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 CEILING Note: Clearance from opening to perpendicular wall. Figure 3.5 Clearances to Mantel Legs or Wall Projections 1/2 in.

  • Page 11: Termination Locations

    Measure vertical clearances from this surface. Measure horizontal clearances from this surface. (See Figure 4.4 for specifi c clearances) Figure 4.1 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 2 FT. 20 INCHES MIN. MIN.
  • Page 12 Figure 4.4 Minimum Clearances for Termination CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED L** = 7 ft.

  • Page 13: Vent Information And Diagrams

    45º runs, one foot of diagonal is equal to 8.5 inches hori- zontal run and 8.5 inches vertical run. A length of straight pipe is allowed between two 45º elbows (see Figure 5.1). Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Vertical 8-1/2 in.

  • Page 14: Use Of Flex Vent

    However, the vent at- tachment point and the fi restop loca- tion are considered to be supports. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 3 in. CLEARANCE FLEX-VENT Figure 5.3 TERMINATION 1 in.

  • Page 15: Vent Diagrams

    fi replaces, a one foot minimum vertical vent section is required before installing fi rst elbow. Figure 5.4 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 WARNING V Minimum SL-350TRS-D 90º...
  • Page 16 fi replaces, a one foot minimum vertical vent section is required before installing fi rst elbow. Figure 5.5 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 V Minimum 90º Elbow 1/2 ft.
  • Page 17 fi replaces, a one foot minimum vertical vent section is required before installing fi rst elbow. Figure 5.6 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Maximum Maximum Model: SL-350TRS-D 1-1/2 ft.
  • Page 18 The exhaust restrictor can be located in the appliance manual bag. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Exhaust restrictor Instructions 1. Install the exhaust restrictor over the center of the ex- haust outlet in the fi...
  • Page 19 2 ft. 3 ft. 4 ft. 5 ft. Note: Use SL-D Series components only. Figure 5.8 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Maximum Minimum SL-350TRS-D 90º Elbow 1-1/2 ft. 457 mm 152 mm 2 ft.
  • Page 20 H when using fl ex vent except when using the simple up and out installation (see Figure 5.3). Figure 5.9 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 90º Elbow 1/2 ft.. 152 mm 1 ft.
  • Page 21 2. Top Vent - Vertical Termination - (continued) Four 90º Elbows Note: Use SL-D Series components only. Figure 5.17 Figure 5.17 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Min. 1-1/2 ft. 457 mm 4 ft. Max.
  • Page 22 Two 90º Elbows Note: Use DVP Series components only. Figure 5.12 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Two 90º Elbows Note: Use DVP Series components only. Use two 90º elbows for corner installations.
  • Page 23 Figure 5.13 4. Rear Vent - Vertical Termination One Elbow Note: Use DVP Series components only. Figure 5.14 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Maximum Minimum Back to Back 1-1/2 ft. 457 mm Elbows 3-1/2 ft.
  • Page 24 Note: Use DVP Series components only. Figure 5.15 Three Elbows Note: Use DVP Series components only. Figure 5.16 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 INSTALLED HORIZONTALLY Maximum Back to Back 1-1/2 ft. 457 mm 3-1/2 ft.

  • Page 25: Vent Clearances And Framing

    SHIELD FIRESTOP WALL Figure 6.2 DVP Horizontal Venting Clearances to Combustible Materials Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 B. Wall Penetration Framing SL-750TRS-IPI-E SL-550TRS-IPI-E SL-350TRS-D * Shows center of vent framing hole for top or rear venting.

  • Page 26: Vertical Penetration Framing

    • Field construct additional shield height if insulation is deeper than height of attic shield. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 HOLE SHOULD MEASURE 10 IN. X 10 IN. (254 MM X 254 MM) INSIDE TO INSIDE Figure 6.4...

  • Page 27: Appliance Preparation

    Figure 7.2 Rotate the top heat shield to the vertical position as shown above. The heat shield must remain in the vertical position. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 2 SCREWS Figure 7.3 Replace the two screws as shown.

  • Page 28: Rear Vent

    Figure 7.8 Fold the tabs toward the center of the fi re plug (90°) and remove the insulation gasket. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Figure 7.9 Cut the metal retaining band and fold the sides out.

  • Page 29: Securing And Leveling The Appliance

    • Keep nailing tabs fl ush with the framing. • Secure the appliance to the framing by using nails or screws through the nailing tabs. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 NAILING TABS BOTH SIDES Figure 7.13 Proper positioning, leveling and securing of an...

  • Page 30: Installing Vent Pipe

    fi re or explosion may occur. Do not break silicone seals on slip sections. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Assembling Pipe Sections Insert the inner fl ue of section A into the fl ared inner fl ue of section B.
  • Page 31 1-1/2 inch outer fl ue overlap is maintained between the pipe section and slip section. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 The pipe and slip section need to be secured by driving two screws through the overlapping portions of the outer fl...

  • Page 32: Disassembly Of Vent Sections (Dvp Pipe)

    • Do NOT allow vent to sag below connection point to appliance. Improper support may allow vent to sag or separate. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Figure 8.8 Securing Vertical Pipe Sections Figure 8.9 Securing Horizontal Pipe Sections Figure 8.10 Rotate Seams for Disassembly...

  • Page 33: Installing Heat Shield And Horizontal Termination Cap (Dvp Pipe)

    (pipe section) to properly space it from the pipe section. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Installing the Horizontal Termination Cap Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

  • Page 34: Assembly Of Vent Sections (Sl Pipe)

    Note: The end of the pipe sections with the lances/tabs on it will face toward the appliance. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 WARNING Fire Risk...

  • Page 35: Installing Wall Shield Firestops And Horizontal Termination Cap (Sl Pipe)

    FIRESTOP (INTERIOR) Figure 8.15 Heat Shield, Interior & Exterior Firestops Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 • ALWAYS maintain specifi ed clearances around venting and fi restop systems. • Install fi restops as specifi ed.

  • Page 36: Installing Roof Flashing And Vertical Termination Cap

    • Restricted air fl ow affects burner operation. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Caulk the gap between the roof fl ashing and the outside diameter of the pipe. Also caulk the perimeter of fl ashing that contacts roof surface as shown in Figure 8.18.
  • Page 37 Caulk around the top of the storm collar (see Figure 8.16). Figure 8.19 Assembling the Storm Collar Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Figure 8.20 Assembling the Storm Collar Around the Pipe...

  • Page 38: Gas Information

    3.5 inches Manifold pressure w.c. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 C. Gas Connection Note: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1.
  • Page 39 • This valve has been preset at the factory. • Changing valve settings may result in fi re hazard or bodily injury. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 HIGH ALTITUDE INSTALLATIONS U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A.

  • Page 40: Electrical Information

    THERMOCOUPLE VALVE Figure 10.2 Standing Pilot Ignition Wiring Diagram Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 B. Connecting to the Appliance • This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.

  • Page 41: Intellifi Re Ignition System Wiring

    BATTERY PACK Figure 10.4 Intellifi re Ignition Wiring Diagram with Wall Switch or Thermostat Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Do not wire 110VAC directly to ignition module. Permanent damage to module will occur. Connect ignition module to 3 VAC transformer as instructed.
  • Page 42 3 VAC ORANGE GROUND TO FIREPLACE PLUG IN CHASSIS WIRES BATTERY PACK (TO BROWN) REMOTE PLUG IN VALVE Figure 10.4 Intellifi re Ignition Wiring Diagram with Remote Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07...

  • Page 43: Junction Box Installation

    (1/4 inch male) as shown. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 GRN wire inside box Figure 10.5 Junction Box Detail...

  • Page 44: Finishing

    3-1/2 in. 1/2 in. NON-COMBUSTIBLE ZONE Figure 11.2 Non-Combustible Zone Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 CEILING Note: Clearance from opening to perpendicular wall. Figure 11.3 Clearances to Mantel Legs or Wall Projections 1/2 in.

  • Page 45: Facing Material

    • See Section 1 for combustible/non- combustible defi nitions. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Note: There are 3 metal tabs holding the non-combustible board in place for shipping. These tabs are to be cut off or bent back before fi...

  • Page 46: Splatter Guard

    Step 3. Crease fl aps on left and right sides of splatter guard using the scored line as the guide. See Figure 11.7. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Figure 11.7 Step 4. Center the splatter guard in front of the unit as shown in Figure 11.8.
  • Page 47 See Figure 11.13. Figure 11.12 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Figure 11.13 Once plumbing and wiring are complete on the fi replace, the lower access panel may be closed until the time that the splatter guard must be removed for fi...

  • Page 48: Doors

    Finishing materials 1 inch maximum thick. Stop fi nishing material fl ush with opening. Figure 11.17 Overlap Fit Door (Chad and Halston) Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 FINISHING MATERIAL 4 IN. MAXIMUM THICKNESS 11.16...

  • Page 49: Appliance Setup

    SENSOR SWITCH BLUE Figure 12.2 Detail of Fan Wiring with Rheostat Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 D. Lava Rock, Mineral Wool/Ember Placement Placing the Lava Rock (SL-350TRS-D only) See Section 12F for Lava Rock placement instructions.

  • Page 50: Install Refractory

    fi re- box left wall such that it is against the back refractory (see Figure 12.6). Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Figure 12.6 Step 2.

  • Page 51: Positioning The Logs

    #4 should rest on the groove that is located on the top of log #1. Swing the center branch toward the burner (see above). Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Log Set Assembly: LOGS-350TRS-D No lava rock may be placed past this edge.
  • Page 52 Log #4 (SRV2113-703): Locate the notch on the bottom of log # 4. Mate the notch with the shoulder screw that is located on the burner top. Mate the rear groove with the far right grate tine as shown above. Apply the supplied lava rock as shown above. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Figure 7...
  • Page 53 The pilot should be centered within the large notch on log #2. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Log Set Assembly: LOGS-SL550TRS-D 1 2 2...
  • Page 54 #4. Log 5 must be pushed back against refractory. See Figure 3. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Figure 1. LOG TOUCHES REFRACTORY PANEL NOTCH Figure 2.
  • Page 55 LOG #2 (SRV2066-703) Place log #2 on the grate bar and push it back against refractory. The pilot should be centered within the large notch on log #2. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Log Set Assembly: LOGS-SL750TRS- D LOG NOTCHES...
  • Page 56 LOG #5 (SRV2065-701) Place log #5 on log #2. Log #5 will mate with the grooves located on the top side of Log #4. See Figure 3. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 LOG/BURNER DETAIL CONTACT AREA Figure 1.

  • Page 57: Glass Assembly

    GLASS ASSEMBLY Figure 12.2 Glass Assembly Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 H. Grilles and Trim Install optional marble and brass trim surround kits as de- sired. Marble, brass, brick, tile, or other noncombustible materials can be used to cover up the gap between the sheet rock and the appliance.

  • Page 58: Operating Instructions

    • Only use glass door certifi ed for use with appliance. • Glass replacement should be done by qualifi ed technician. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 WARNING HOT! DO NOT TOUCH.

  • Page 59: Lighting Appliance

    For additional information on operating your Hearth & Home Technologies fi replace, please refer to www.fi replaces.com. Final inspection by Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

  • Page 60: Standing Pilot Ignition

    Hearth & Home Technologies fi replace, please refer to www.fi replaces.com. Final inspection by Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 • If you cannot reach your gas sup- plier, call the fi re department.

  • Page 61: After Appliance Is Lit

    Metallic noise Is it normal to see the pilot fl ame burn continually? Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 • Prevent accidental appliance operation when not attended. • Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

  • Page 62: Troubleshooting

    ON position. b. Thermopile may not be gener- ating suffi cient millivoltage. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Corrective Action Check the spark at the electrode and pilot. If no spark and electrode wire is properly connected, replace the ignitor.
  • Page 63 7. Flame burns blue a. Insuffi cient oxygen being supplied. and lifts off burner. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Possible Cause Turn the valve knob to the ON position. Place the ON/OFF switch in the ON position.

  • Page 64: Intellifi Re Ignition System

    fl ame rectifi cation has not occurred.) Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Corrective Action Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to correct terminals on module and pilot assembly.
  • Page 65 Module is not grounded. d. Module voltage output / Valve/Pilot solenoid ohms readings. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Possible Cause Verify that module is securely grounded to metal chassis of appliance. Verify that wire harness is fi rmly connected to module.

  • Page 66: Maintaining And Servicing Appliance

    • Delayed ignition or explosion • Exposure to combustion fumes • Odors Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 CAUTION Handle glass assembly with care. NOTE: Clean glass after initial 3-4 hours operation.

  • Page 67: Maintenance Tasks

    2. Replace batteries in remote transmitters and battery-powered receivers. 3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure or leaking. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Maintenance Tasks...

  • Page 68: Reference Materials

    6-7/8 21-3/8 32-3/8 34-1/2 8-3/4 16-1/4 22-3/4 11-3/8 15-7/8 6-5/8 2-1/8 Figure 16.1 Appliance Dimensions Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Ø SL-350TRS-D SL-550TRS-E Millimeters Inches Millimeters 31-1/8 27-3/16 18-1/16 31-1/8 3-9/16...

  • Page 69: Vent Components Diagrams

    DVP-AS (Attic Shield) 10 in. (254 mm) 5 in. (127 mm) DVP-HVS (Vent Support) Figure 16.2 DVP vent components Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Effective Length Pipe Inches Millimeters DVP4 DVP6...
  • Page 70 12 in. (305 mm) DVP-TRAP Horizontal Termination Cap DVP-TRAP1 DVP-TRAPK1 DVP-HPC1 Figure 16.3 DVP vent components Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 8 in. Heat (203 mm) Shield Term Cap Term Cap Trap1...
  • Page 71 Trap Cap Brick Extension DVP-TRAPFL Flashing DVP-HSM-B Extended Heat Shield Figure 16.4 DVP vent components Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) 5 in. (127 mm) 13-7/8 in.
  • Page 72 (314 mm) 1-5/8 in. (41 mm) DVP-HPC High Performance Cap Figure 16.5 DVP vent components Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 7-3/8 in. (187 mm) 17-3/4 in. (451 mm) 7-1/4 in. (184 mm) 5-1/4 in.
  • Page 73 8-1/8 in. (206 mm) 15 in. (381 mm) Figure 16.7 SL Series Vent Components Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 13 in. Effective Length (330 mm) 5-3/4 to 8-3/8 in. 5-1/2 in.
  • Page 74 H when using the snorkel cap except when using the simple up and out installation. WALL BRACKET (SL-SERIES) Figure 16.9 SL D-Series Vent Components Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 6-1/2 in. Pipe Length/Inches SL-06D 5-3/4...

  • Page 75: Log Set Assembly

    SL-350TRS-D SL-350TRS-IPI Service Parts Beginning Manufacturing Date: June 2007 Service Parts Diagram Ending Manufacturing Date: Active Log Set Assembly Part number list on following page. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07...

  • Page 76: Service Parts List

    Pilot Orifi ce LP Regulator NG Regulator LP Additional service part numbers appear on following page. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 SERIAL # STANDING PILOT CONVERSION KITS IPI CONVERSION KITS SL-350TRS-D, SL-350TRS-IPI...
  • Page 77 Flex Ball Valve Assembly Valve Bracket Orifi ce NG (#44C) Orifi ce LP (#55C) Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 SL-350TRS-D Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: Active SERIAL #...
  • Page 78 Flex Ball Valve Assembly Valve Bracket Orifi ce NG (#44) Orifi ce LP (#55) Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 SERIAL # SL-350TRS-IPI Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: Active...
  • Page 79 SL550TRS-IPI-E Service Parts Service Parts Diagram Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: Active Log Set Assembly Part number list on following page. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07...
  • Page 80 Pilot Orifi ce NG Pilot Orifi ce LP Regulator NG Regulator LP Additional service part numbers may appear on following page. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 SERIAL # PART NUMBER LOGS-SL550TRS-D SRV2065-704...
  • Page 81 SL-750TRS-IPI-E Service Parts Beginning Manufacturing Date: June 2007 Service Parts Diagram Ending Manufacturing Date: Active Log Set Assembly Part number list on following page. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07...
  • Page 82 Pilot Orifi ce NG Pilot Orifi ce LP Regulator NG Regulator LP Additional service part numbers may appear on following page. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 SERIAL # PART NUMBER LOGS-SL750TRS-D SRV2066-704...
  • Page 83 Module Valve NG Valve LP Thermostat Wire Assembly Flex Ball Valve Assembly Valve Bracket Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 SL550TRS-IPI-E, SL-750TRS-IPI-E SERIAL # SL-550TRS-IPI-E SL-750TRS-IPI-E Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: Active...

  • Page 84: Limited Lifetime Warranty

    Product. HEAT & GLO also reserves the right to discontinue styles and products. © 2005 Hearth & Home Technologies Inc. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 060-981D 3/05...

  • Page 85: Contact Information

    6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending. Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07 Heat & Glo, a brand of Hearth & Home Technologies Inc.

This manual is also suitable for:

Sl-350trs-ipiSl-550trs-ipi-eSl-750trs-ipi-e

Table of Contents