Adam MDW – 300L User Manual

Health and fitness scale with bmi

Advertisement

Adam Equipment
MDW – 300L
HEALTH AND FITNESS SCALE with BMI
ADAM EQUIPMENT CO. LTD.
p.n. 700660159 Rev. A1, January 2012
© Adam Equipment Company 2012

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MDW – 300L and is the answer not in the manual?

Questions and answers

Summary of Contents for Adam MDW – 300L

  • Page 1 Adam Equipment MDW – 300L HEALTH AND FITNESS SCALE with BMI ADAM EQUIPMENT CO. LTD. p.n. 700660159 Rev. A1, January 2012 © Adam Equipment Company 2012...
  • Page 2 © Adam Equipment Company 2012...
  • Page 3: Table Of Contents

    SETTING UP THE SCALE ................5 FUNCTION ....................7 WEIGHING ....................7 MEASURING HEIGHT................8 MEASURING BODY MASS INDEX (BMI) ..........8 CALIBRATION....................9 USER PARAMETERS................10 RS232 COMMUNICATIONS ..............11 ERROR MESSAGES ................. 15 10.0 WARNING ....................15 Page © Adam Equipment Company 2012...
  • Page 4 Page © Adam Equipment Company 2012...
  • Page 5: Introduction

    22.4” X 10.8” X 51.5” Net weight 13 kg / 29 lb. Environment for Use Temperature: 5ºC-40ºC; Humidity: <85℅ RH Power 12vDC 500mA adapter Battery Internal, re-chargeable 6V 4Ah, 50 hours approx. Calibration External calibration through the keypad. Page © Adam Equipment Company 2012...
  • Page 6: Display And Key Descriptions

    This indicates when the scale is being used with the AC adapter. ZERO This indicator will be displayed in the left corner when the scale reaches zero. The Net weight is displayed, Tare weight is at zero. Page © Adam Equipment Company 2012...
  • Page 7: Setting Up The Scale

    6. Insert the pillar (3) into the tube support (6). 7. Rotate the pillar to position the indicator (1) in the direction desired, and then secure using the 2 screws (5) into the fixing tube (6). Page © Adam Equipment Company 2012...
  • Page 8 (9) of the upper and lower brackets (8) & (12). 15. Secure the bolt and washer to the bracket on the base (10) 16. Tighten the bolt on the upper bracket (9). Page © Adam Equipment Company 2012...
  • Page 9: Function

    • Print Function: To send the weighing result to a printer or computer press the [Print/Hold] key when the [Print/Hold] key has been set up in the parameter section to work as print function. Page © Adam Equipment Company 2012...
  • Page 10: Measuring Height

    • Press the [Unit/BMI] key to exit the BMI mode and return to normal weighing. • The Hold function will work as described above whilst in the BMI mode. Page © Adam Equipment Company 2012...
  • Page 11: Calibration

    “CAL. Er” and return back to step 4 for re- calibration. ) 6. Check the calibration by putting the weight that you calibrated at back on the scale, if it is off repeat the calibration process again. Page © Adam Equipment Company 2012...
  • Page 12: User Parameters

    0 = No RS232 Function. 1 = Continuously outputs display data. 2 = Output display data when PRINT pressed S.F. 3 = Bi-directional communication (the scale receives and executes commands from the HOST device) Page © Adam Equipment Company 2012...
  • Page 13: Rs232 Communications

    No RS232 function. The scale will not transmit or receive any data although the scale is equipped with RS232. The RS232 function can be only activated when the scale is in normal weighing mode. Page © Adam Equipment Company 2012...
  • Page 14 8.5.2 Key to symbols used <LF> Line Feed character (hex 0AH) <CR> Carriage Return character (hex 0DH) <ETX> End of Text character (hex 03) <SP> Space (hex 20H) H1H2H3 Three status bytes. Refer to Table1 for definition. Page © Adam Equipment Company 2012...
  • Page 15 P11 setting. <LF>u1u2<CR><LF> H1H2H3<CR><ETX> (6) Command: X<CR> (58h 0dh) Response: power off the scale, the same as pressing the ON/OFF button to turn off the scale. (7) Command: all others Response: Unrecognized command <LF>?<CR><ETX> Page © Adam Equipment Company 2012...
  • Page 16 1= net weight 0= eeprom OK always 0 always 0 1= eeprom error always 1 always 1 always 1 always 1 always 1 always 1 always 0 always 1 always 0 parity Parity parity Page © Adam Equipment Company 2012...
  • Page 17: Error Messages

    • When lifting the height meter, extract it directly upwards without using excessive force. • Do not lift the scale using the height pillar. Lift by the base only. Page © Adam Equipment Company 2012...
  • Page 18 Page © Adam Equipment Company 2012...
  • Page 19 Shielded interconnect cables must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by Adam Equipment could void the user's authority to operate the equipment. WEEE COMPLIANCE...
  • Page 20 For a complete listing of all Adam products visit our website at www.adamequipment.com © Copyright by Adam Equipment Co. Ltd. All rights reserved. No part of this publication may be reprinted or translated in any form or by any means without the prior permission of Adam Equipment.

Table of Contents