Table of Contents
Advertisement
6 - Basic Recording
3. Press the EQUALIZER ON/OFF button to the right of the
LOW FREQ knob to turn the equalizer on/off.
The equalizer parameters are as follows.
GAIN
Setting range: ±12
HIGH
dB
(Default: 0 dB)
Setting range: ±12
MID
dB
(Default: 0 dB)
Setting range: ±12
LOW
dB
(Default: 0 dB)
Use track SELECT buttons to select desired tracks.
Use INPUT SOURCE buttons to select desired inputs.
Use HIGH, MID and LOW GAIN knobs to adjust the gain of
each band.
Use the HIGH, MID and LOW FREQ knobs to adjust the
center frequency of each band.
Use the MID Q knob to set the resonance (width) of the MID
FREQ band.
Setting range:
to
0.25
NOTE
• The "Q" value is the center frequency of the equalizer divided by
the bandwidth. A high Q value reduces the range of the cut or
boost applied to the frequencies. Depending on the equalizer
setting, the graph at the top of the screen changes.
• If you press the F1 (
EQ FLAT
the open Mixer screen will be restored to their default values.
3. After making the settings, press the HOME button to return
to the Home screen.
DIGITAL TRIM setting (track only)
Depending on the playback sound, EQ boosting could cause
distortion (digital clipping). If this happens, use the DIGITAL TRIM
to lower the playback level before the EQ.
1. Use the CURSOR (
/
/
5
b
g
to the
display area.
DIGITAL TRIM
Digital trim
2. Turn the JOG/DATA dial to set the value.
Setting range:
to
-42dB
36
TASCAM DP-32SD
FREQ
Setting range: 1.7 kHz to
18 kHz
(Default: 10 kHz)
Setting range: 32 Hz to
18 kHz
(Default: 1.0 kHz)
Setting range: 32 Hz to
1.6 kHz
(Default: 100 Hz)
(Default:
)
16
0.5
) button, all the settings shown on
/
) buttons to move the cursor
t
(Default:
)
+6dB
0dB
Sending signals to internal/external
effects
This unit has two external effect sends (EFF 1 and EFF 2) and a
send for the internal effects (INSERT EFFECT).
You can adjust send levels for each track. For details about the
built-in send effects, see "Send effects" on page 53.
Follow these procedures to enable use of these effects.
1. Use the CURSOR (
/
/
5
b
g
to the
SEND EFF 1/EFF 2
2. Turn the JOG/DATA dial to enable the effect.
Options:
(default),
OFF
PRE
PRE
This sends the track pre-fader signal to the effect send
bus. The effect send signal level is not affected by the track
fader.
POST
This sends the track post-fader signal to the effect send
bus. The effect send signal level is affected by the track
fader.
3. Use the SEND EFF 1/EFF 2 knobs to adjust the external send
levels.
Setting range:
to
(Default:
0
127
4. Use the SEND MASTER 1/MASTER 2 knobs to adjust the
internal send levels.
Setting range:
to
(Default:
0
127
Enabling insert effects
This unit has dynamic and guitar effects that can be used as
insert effects. For details about these effects, see "Dynamic
effects" on page 52 and "Guitar effects" on page 52.
1. Use the CURSOR (
/
/
5
b
g
to the
area.
INSERT EFFECT
Insert effect
indicator
2. Turn the JOG/DATA dial to enable/disable the insert effect.
Options
OFF:
INSERT EFFECT
ON:
INSERT EFFECT
/
) buttons to move the cursor
t
area.
Effect sends
,
POST
)
0
)
0
/
) buttons to move the cursor
t
indicator unlit (default)
indicator lit
Advertisement
Table of Contents
