Barco RLS W12 User Manual
  1. Manuals
  2. Brands
  3. Barco Manuals
  4. Projector
  5. RLS W12
  6. User manual

Barco RLS W12 User Manual

Hide thumbs Also See for RLS W12:
Table of Contents

Advertisement

Quick Links

See also: Reference Manual
RLS W12
User manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RLS W12 and is the answer not in the manual?

Questions and answers

Related Manuals for Barco RLS W12

Summary of Contents for Barco RLS W12

  • Page 1 RLS W12 User manual...
  • Page 2 Barco nv Projection Division Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/esupport Visit us at the web: www.barco.com Revision. : 01 R5905889 Printed in China...
  • Page 3 Barco. If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS 1. SAFETY 1.1 General considerations 1.2 Important safety instructions 2. GENERAL 2.1 Installation requirements 2.2 Unpacking the projector 2.3 Initial inspection 2.4 Projector configurations 2.5 Projector air inlets and outlets 2.6 Installation process overview 3. PROJECTOR PARTS AND FUNCTIONS 3.1 Projector front view 3.2 Projector Rear view 3.3 Input and Communication...
  • Page 5 TABLE OF CONTENTS 5. GETTING STARTED 5.1 RCU & Local keypad 5.2 Power on projector 5.3 Switching to standby 5.4 Power off projector 5.5 Source selection 5.6 Changing OSD language 5.7 Adjusting the lens by horizontal and vertical lens shift 6.
  • Page 6 TABLE OF CONTENTS 8. IMAGE 8.1 Image menu overview 8.2 Contrast 8.3 Brightness 8.4 Sharpness 8.5 Noise Reduction 8.6 Color Temperature 8.7 Input Balance 8.8 Aspect Ratio 8.9 Timings 8.10 Auto Image 8.11 Color Mode 9. LAYOUT 9.1 Layout menu overview 9.2 Zoom 9.3 Main Select 9.4 PIP Select...
  • Page 7 TABLE OF CONTENTS 11. ALIGNMENT 11.1 Alignment menu overview 11.2 Adjusting screen orientation 11.3 Rear Projection 11.4 Ceiling Mode 11.5 Lens Control 11.6 Lens To Midposition 11.7 Dynamic Contrast 11.8 Gamma 11.9 Internal Patterns 11.10 Color Space 11.11 Custom Color Space 11.12 Warp 11.13 Blanking 11.14 ScenergiX...
  • Page 8 TABLE OF CONTENTS 13. SERVICE 13.1 Service menu overview 13.2 Service message of the projector 13.3 Lamp Hour Reset 13.4 Blue Only 13.5 Factory Reset 14. MAINTENANCE 14.1 Lamp Replacement 14.2 Replace the filter (for inlet Ventilation) 14.3 Clean the dust filter(for outlet Ventilation) 14.4 Cleaning the lens 14.5 Cleaning the exterior of the projector 14.6 Simple troubleshooting...

  • Page 9: Safety

    Read this chapter attentively. It contains important information to prevent personal injury while installing and using a RLS W12 projector. Furthermore, it includes several cautions to prevent damage to the RLS W12 projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing your RLS W12 projector.

  • Page 10: Important Safety Instructions

    PERSONNEL, AUTHORIZED to operate professional projection systems. A RLS W12 projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp and associated circuits.
  • Page 11 • Do not place flammable or combustible materials near the projector! • Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe.
  • Page 12 If the product exhibits a distinct change in performance, indicating a need for service. • Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part.

  • Page 13: General

    Observing the specification mentioned in this chapter is critical for projector performance. Neglecting this can result in loss of warranty. 2.1 Installation requirements Environment conditions Table below summarizes the physical environment in which the RLS W12 projector may be safely operated or stored. Environment Operating Non-Operating Ambient Temperature 0 °C (32 °F) to 40 °C (104 °F)

  • Page 14: Projector Weight

    Projector weight Do not underestimate the weight of the RLS W12 projector. The projector weights about ±34 kg (±72.75lb.) without lens. Be sure that the pedestal or ceiling mount on which the projector has to be installed is capable of handling five (5) times the complete load of the system.

  • Page 15: Initial Inspection

    Save all packing material until the inspection is completed. If damage is found, file claim with carrier immediately. The Barco Sales and Service office should be notified as soon as possible.

  • Page 16: Projector Configurations

    This check should confirm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and scratches, and that the operating panel is not scratched or cracked. The Barco Sales and Service office should be notified as soon as possible if this is not the case.

  • Page 17: Positioning The Projector

    (F) as illustrated below. Within these shift ranges the projector and lens perform excellently. Configuring the projector outside these shift ranges will result in a slight decline of image quality. RLS W12 02/12/2014...
  • Page 18 Side to side tilt, however, must not exceed ±10°. This limit ensures that the lamp in the projector operates properly and safely. 10° 10° ±15° ±15° 10° 10° Tilting allowed without problems No tilting allowed in this area No tilting allowed in this area RLS W12 02/12/2014...

  • Page 19: Projector Air Inlets And Outlets

    2.6 Installation process overview Quick setup The following steps describe briefly how to setup your RLS W12 projector in a table mount front projection. Note that each step refers to a corresponding procedure, which is more detailed and illustrated. 1. Install the batteries of the remote control. See page 20: 4.1 Remote control unit (RCU)

  • Page 20: Projector Parts And Functions

    Use this button to start up or Use the buttons to scroll, shut down the projector configure or adjust items on the OSD or toggle between STBY INPUT different images. Used to toggle between different STBY INPUTS input signal source RLS W12 02/12/2014...

  • Page 21: Input And Communication

    The communication interface of the RLS W12 projector supports RS232 serial communication. You can use the RS232 input to connect a local PC to your RLS W12 projector. By this way you can configure and control your RLS W12 projector from your local PC.
  • Page 22 Standard 15-pin VGA connection socket to connect to RGB, high-definition component input or PC.The projector will automatically detect the resolution of the input signal. 10. RGBHV/YUV2 Optional multi purpose input which can be inserted in the free slots. RS232 input (Sub-D) port Input Signal B/Pb R/Pr RGBHV Composite Video RLS W12 02/12/2014...

  • Page 23: Status Lights Of Led

    The time period of each step in the above LED blinking pattern is 500 milliseconds, e.g., for“Cooling / Warm up”state, the green LED will ON for 500 milliseconds, and then OFF 500 milliseconds, and then repeat the above LED pattern. RLS W12 02/12/2014...

  • Page 24: Connecting The Projector To Other Devices

    12V Trigger output as illustrated. After you have done so, Your screen will lower automatically whenever you turn on your projector for your convenience. Retractable screen or other Sleeve = Ground 12V device Tip = +12V 200mA 200mA RLS W12 02/12/2014...
  • Page 25 Connect your PC or other devices with VGA output to the VGA input connectors on the projector to be used as the source of image input. 200mA 200mA Desktop or Notebook 200mA 200mA Raccordé à la prise murale AC POWER AC MAINS SWITCH 100-240 Volts 50/60Hz B/Pb R/Pr Desktop or Notebook RLS W12 02/12/2014...

  • Page 26: Rgbs Connection

    If the projector is unable to pick up the IR signals from the remote control due to distance or obstacles (i.e. wall or cabinet doors), you can connect an external IR repeater to the projector’s IR INPUT jack to extend the effective signal reception range. IR sensor Remote control IR repeater 200mA 200mA RLS W12 02/12/2014...

  • Page 27: Component Connection

    200mA 200mA DTV set-top-box or other compo- (YPbPr) nent (YPbPr) input source 10/100 BASE-T Connects the projector to your PC via network to have direct control of the projector from the PC. 200mA 200mA Desktop or Notebook RLS W12 02/12/2014...

  • Page 28: Physical Installation

    • If the infrared receiver is exposed to fluorescent lamp or strong sunlight, the remote control may not operate normally. • Refer to the regulations enforced by your local government on the disposal of used batteries; improper disposal could damage the environment. • Battery type R03. Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used. RLS W12 02/12/2014...

  • Page 29: Remote Control Overview

    "arrow keys" The enter button selects a item when in the menu. select button press "enter" When not in the menu the enter button will activate the lens adjust function. select and return to previous menu press "enter" RLS W12 02/12/2014...

  • Page 30: Range Of Effective Remote Control Signal Reception

    Range of effective remote control signal reception The diagram below illustrates the range of effective remote control signal reception. 40° 40° Avoid placing the remote control at places of high temperature or humidity as it could cause the remote control to malfunction. RLS W12 02/12/2014...

  • Page 31: Lenses

    4.Input & Communication 4.2 Lenses Available lenses for the RLS W12 projector • R9832760 : J lens (1,85-2,4 : 1) - Standard Lens • R9832761 : J lens (1,56-1,86 : 1) - Short Throw Lens • R9832762 : J lens (2,4-4,0 : 1) - Longer Zoom lens • R9832763 : J lens (0,84-1,03 : 1) - Extreme Wide Angle Lens...
  • Page 32 Original image size Zoom out Zoom in ens Zoom: To adjust the lens zoom with the RCU press “enter” when the OSD is not active RLS W12 02/12/2014...
  • Page 33 SPECIFICATION) of half the screen width in both directions. For instance, if you are using a 80" × 50" screen, you will be able to move the image left or right by no more than 12". This illustration shows normal horizontal lens shift without the use of special specification lens or projector. RLS W12 02/12/2014...

  • Page 34: Connecting The Projector With The Power Net

    4. Secure the power plug by locking the plug holder clamp. VOLTAGE AC POWER SWITCH AC MAINS 交流電源選擇 交流電源開關 交流電源輸入     VOLTAGE AC POWER SWITCH AC MAINS 交流電源選擇 交流電源開關 交流電源輸入 Connect to Wall plug RLS W12 02/12/2014...
  • Page 35 To avoid thermal stress that can lead to premature lamp failure, never unplug the power cord while the lamp cooling fans are running. Never unplug the power cord to power down the projector, first switch off the power switch and then unplug the power cord. RLS W12 02/12/2014...

  • Page 36: Alignment Of A Table Mounted Projector

    3. Turn the adjustable feet in or out until the projected hatch pattern has a perfect rectangle shape and is leveled. When this is achieved, the projector is set horizontal and vertical at right angles to the screen. Angle adjustment Angle adjustment RLS W12 02/12/2014...

  • Page 37: Mounting The Ceiling Mount

    Ceiling Mount Order Info: 1. R9849999-Ceiling mount 2. R9841260-Short Pulley 400mm to 765mm 3. R9841261-Long Pulley 800mm to 1165mm Ote: Two hole patterns are available for ceiling mounting: M6x15(6pcs) or M8x15(3pcs) Please check your support system for compatability. RLS W12 02/12/2014...

  • Page 38: Getting Started

    When the projector is turned off, it is required to wait for at least 90 seconds to re-start the projector to complete the cooling of lamp. Starting image projection via the standby key. STBY Press key once on the local keypad or on the remote control. RLS W12 02/12/2014...

  • Page 39: Switching To Standby

    By factory default, the OSD menu of the projector is displayed in English. If you want to change default language. Press the MENU on Remote control or keypad, then go to Control -> Languages to select the language that you want. RLS W12 02/12/2014...

  • Page 40: Adjusting The Lens By Horizontal And Vertical Lens Shift

    Press ENTER again to adjust Press ENTER once to adjust Press ENTER once to Adjust zoom and focus vertical and horizontal lens zoom and focus with cross Lines shift with cross line shift line -> -> -> Enter Enter Enter Enter RLS W12 02/12/2014...

  • Page 41: Osd Menu

    • Alignment: groups all controls necessary during the setup of the projector onto a screen. • Control: contains the accessibility settings of the projector, such as address and communication setup. • Service: contains information about how the projector is performing. This information will be useful when calling for a service intervention. RLS W12 02/12/2014...

  • Page 42: How To Activate The Osd Menu

    When restarting the projector from stand-by, the menu memory is reset. After re-opening the main menu and selecting an item, the previous selected sub item of that selected item is highlighted and can be opened just by pressing or ENTER. RLS W12 02/12/2014...

  • Page 43: Input

    Black White Auto Image Adjust Auto Always Each input module must be configured before these module can be used. This configuration is necessary so that the projector knows which type of signal is connected to its input. RLS W12 02/12/2014...

  • Page 44: Input Selection

    48Hz, 50Hz, 60Hz Choose this option to set image output frequency at 48Hz, 50Hz or 60Hz If you enable PIP, the projector will automatically synchronize the frequency of the PIP input signal with the main input signal. RLS W12 02/12/2014...

  • Page 45: Auto Power Off

    7.8 Auto Image Adjust You can configure the Auto Image Adjust function to one of the following three modes: Off =NEVER Auto =When not done before(or when done first time) Always =When new source selected or new source connected. RLS W12 02/12/2014...

  • Page 46: Image

    1.88 2.35 Letterbox Native Unscaled H Total H Start Timings H Phase V Start Auto Image Execute Bright Presentation Color mode Video RGB Only Depending on the type of the connected source, some settings are grayed out RLS W12 02/12/2014...

  • Page 47: Contrast

    Contrast and Brightness are interrelated options that affect one another; when you adjust one of them, you might have to fine tune other settings to get the best projection results. The following image illustrates the results of direct brightness adjustment using a random image: Reduced brightness Original image Enhanced brightness RLS W12 02/12/2014...

  • Page 48: Sharpness

    The projector’s default color temperature is set at Native. As color temperature rises, the image will appear to be more blue; as it decreases, the image will appear redder. When you choose “Native”, the projector will disable the white adjustment function of the input device. RLS W12 02/12/2014...

  • Page 49: Input Balance

    • Red Gain Press to adjust the gain of red in bright scales. • Green Gain Press to adjust the gain of green in bright scales. • Green Gain Press to adjust the gain of blue in bright scales. RLS W12 02/12/2014...

  • Page 50: Aspect Ratio

    When used for commercial purposes, including: projection of image in movie theaters, hotels, cafeteria and other public venues, compression or extension of image achieved through the change of aspect ratio may constitute copyright infringement to the rightful owner of the image. Please do so at your own discretion. RLS W12 02/12/2014...

  • Page 51: Timings

    Skewed down It is recommended that when adjusting the image, the horizontal total should be adjusted before the horizontal phase. However, if the image still flickers even after you have adjusted both, try lowering the image noise. RLS W12 02/12/2014...

  • Page 52: Auto Image

    Video Projector optimized for best color performance. Select this mode for a low ambient light condition RGB Only Native image performance. Non corrected. Brightness will be less than 50%. Select this mode for native image performance RLS W12 02/12/2014...

  • Page 53: Layout

    • PIP Position • PIP 9.1 Layout menu overview Zoom Crop Zoom HDMI HDBaseT Main Select YUV1 RGBHV/YUV2 SDI/HDSDI/3G HDMI HDBaseT LAYOUT PIP Select YUV1 RGBHV/YUV2 SDI/HDSDI/3G Top Left Top Right PIP Position Button Left Button Right Split L-R RLS W12 02/12/2014...

  • Page 54: Zoom

    When you want to project PIP image, use this function to specify the image source for the PIP image. This function is identical to Input Selection; for more information, please refer to page 36: 7.2 Input Selection RLS W12 02/12/2014...

  • Page 55: Pip Select

    Refer to the following main and PIP source matrix for a valid main and PIP source selection when PIP is ON. Main select PIP/main source SDI/ RGBHV/ availability HDSDI/ HDBaseT HDMI YUV1 YUV2 HDBaseT HDMI YUV1 RGBHV/YUV2 SDI/HDSDI/3G Source available source not available RLS W12 02/12/2014...

  • Page 56: Lamp

    • Lamp1 and Lamp2 Run Time display • Lamp Performance 10.1 Lamp menu overview Mode Normal Power Single LAMPS Dual High Altitude Mode Power 77.3% - 100% LAMPS Lamp1 Status Lamp2 Status Lamp1 Run Time XX HRS Lamp2 Run Time XX HRS RLS W12 02/12/2014...

  • Page 57: Mode

    The projector will automatically determine the usage hours for lamp1 and lamp2 and choose the lamp with lower hours for the operation. • Dual When you require brighter image from the projector, please operate the projector with Dual lamps. Lamp1 Lamp2 RLS W12 02/12/2014...

  • Page 58: High Altitude Mode

    This function is limited to display purposes to inform the user of Lamp2's total run time. 10.10 Lamp Performance In order to maximize the lamp performance over its life time it is recommended to leave the lamps on for a minimum of 30minutes. RLS W12 02/12/2014...

  • Page 59: Alignment

    Native Brilliant Blend Color Space Custom Red x Red y Green x Green y Blue x Blue y Cyan x Custom Color Space Cyan y Magenta x Magenta y Yellow x Yellow y White x White y RLS W12 02/12/2014...

  • Page 60: Adjusting Screen Orientation

      Rear projection - desktop installation Press MENU  ALIGNMENT Rear Projection and choose ON; the projector is now configured for “rear projection - desktop installation”. Correct Picture canoe   RLS W12 02/12/2014...

  • Page 61: Rear Projection

    Use this function to adjust the lens shift. Refer to page 25: Lens Shift. 11.6 Lens To Midposition After series of lens shift operations, this function can be used to return the lens to the center position. RLS W12 02/12/2014...

  • Page 62: Dynamic Contrast

    3200K or 9300 K. It can then be fine tuned with the input balance RGB gain and RGB offset. 11.11 Custom Color Space This allows user to move the primaries(Red, Green, Blue), secondaries(Cyan, Yellow, Magenta), and white point independently to meet users' requirements RLS W12 02/12/2014...

  • Page 63: Warp

    Vertical Keystone Press  to correct Vertical keystone due to projection angle. —> Rotation Press ◄► to correct incorrect image angle. Press ◄ to adjust angle to Press ► to adjust angle to Correct angle correct. correct. RLS W12 02/12/2014...
  • Page 64 Press ◄► to correct top right corner image bias to correct image. Bottom Left Corner Press ◄► to correct bottom left corner image bias. → Press ◄► to correct bottom left corner image bias to correct image. RLS W12 02/12/2014...

  • Page 65: Blanking

    Custom Warp Press ◄► to ON/OFF. This function need to use with Barco Tool through LAN or RS-232. Reset It will reset all the warp functions to the default settings that is without any warp functions enabled.

  • Page 66: White Level

    Note that this can only be done in the native color temp. The other color temperatures will be not available. Also the brilliant blend function is not applicable when the color mode is in “RGB only”. When select to Brilliant Blend, a warning message will pop up. RLS W12 02/12/2014...
  • Page 67 ScenergiX White Level Black Level Top/Bottom or Keystone Rotation Pin/Barrel 4-corner blanking Blend along corners Black Level Left/Right only Keystone Rotation Pin/Barrel 4-corner blanking Top/Bottom or White Level Left/Right only Blend along corners Black Level Black Level RLS W12 02/12/2014...

  • Page 68: Control

    Button 2 Button 3 YUV1 Button 4 RGBHV/YUV2 CONTROL SDI/HDSDI/3G Button 5 Trigger 1 16:10 16:9 1.88 2.35 Letterbox Trigger 2 Native Auto Auto Source English French Spanish German Portuguese Language Chinese Simplified Chinese Traditional Japanese Korean Russian RLS W12 02/12/2014...

  • Page 69: Ir Address

    Toolset application. To control the projector via network, please connect to the projector via a web browser with the IP address shown on the OSD menu CONTROL —> Network. The home page will be displayed as follows. RLS W12 02/12/2014...

  • Page 70: Subnet Mask

    IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network. RLS W12 02/12/2014...

  • Page 71: Menu Position

    Bottom Left Bottom Right 12.6 Start Up Logo You can use this function to have the projector display the Barco logo in the start up screen. Set to display the Barco logo during start up and to display a blank image.

  • Page 72: Trigger1 ~2

    The user can change the language of the on screen menus and the local display menus to one of the available languages. You can choose from the following nine languages: English, French, Spanish, German, Portuguese, Chinese Simplified, Chinese Traditional, Japanese, Korean and Russian. RLS W12 02/12/2014...

  • Page 73: Service

    H/V Refresh Rate Lamp1 Run Time SERVICE Lamp2 Run Time Reset Lamp1 Lamp Hour Reset Reset Lamp2 Projector Run Time Read-only information Blue Only The command will be executed after Factory Reset confirmation in the prompt dialog box RLS W12 02/12/2014...

  • Page 74: Service Message Of The Projector

    This function will not apply to items including no signal, network, Projector control, startup Logo, language, High Altitude mode and lamp hours When Factory Reset is executed, all source memories created by the projector (i.e. timings files) will be erased RLS W12 02/12/2014...

  • Page 75: Maintenance

    This is why you should wait for no less than 60 minutes for the lamp to cool down in order to perform the replacement safely. 2. Loosen the lamp cover. 3. Take out the lamp cover. RLS W12 02/12/2014...
  • Page 76 6. Insert the new lamp in the direction shown in the illustration into the lamp assembly; tighten the two screws using a screw diver and make sure the lamp is firmly secured to prevent the lamp from shaking or poor contact. 7. Replace the lamp cover and firmly secure the four screws on the lamp cover. RLS W12 02/12/2014...

  • Page 77: Replace The Filter (For Inlet Ventilation)

    New filter (available kit : R9832776, contains 4 high density filters) AUTION: Never clean the filter Always replace with a new one. How to change the filter in the Right side. 1. Loosen the six screws on the projector right side cover. RLS W12 02/12/2014...
  • Page 78 14.Lamp and Filter Maintenance 2. Take out the old filter. 3. Insert new filter. Black side White side 4. Tighten the six screws of right side cover. RLS W12 02/12/2014...
  • Page 79 How to change the filter in the Left and Front side. 1. Loosen the six screws on the projector left side cover. 2. Take out the old filter(left and front). 3. Insert new filter. Black side White side RLS W12 02/12/2014...

  • Page 80: Clean The Dust Filter(For Outlet Ventilation)

    5. Do not leave the cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth. 6. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth. RLS W12 02/12/2014...

  • Page 81: Cleaning The Exterior Of The Projector

    1. The image brightness, contrast, color and 1. Adjust the image brightness, contrast, tint might need proper adjustment. color and tint. The picture looks dim 2. The lamp is due for replacement. 2. Replace the projector lamp. RLS W12 02/12/2014...
  • Page 82 LED indicator on the rear panel of the life; please replace it. picture disappears. projector and see if it is blinking in red. 2. The lamp does not turn on even when the projector has been turned on. RLS W12 02/12/2014...

  • Page 83: Projector Specification

    3 years standard warranty** * Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. **Warranty and service conditions can differ from region to region. Contact your local sales or service representative for more details. RLS W12 02/12/2014...

  • Page 84: Standard Source Files

    SECAM SECAM (M) RGBS 1440x480i SDTV 1440x576i 480i 59.94 576i 480p 59.94 EDTV 576p 1035i 1080i 1080i (Aus) 1080i 59.94 1080i 720p 720p 59.94 720p HDTV 1080p 23.98 1080p 1080p 1080p 29.97 1080p 1080p 1080p 59.94 1080p RLS W12 02/12/2014...

  • Page 85: Sdi Formats

    SMPTE 424M 3Gbps YCbCr 4:2:21 1080P50 3G Level B SMPTE 424M 3Gbps YCbCr 4:2:21 1080P59 3G Level B SMPTE 424M 3Gbps YCbCr 4:2:21 1080P60 3G Level B SMPTE 424M 3Gbps YCbCr 4:2:21 15.4 Dimension 530mm 670mm 265mm RLS W12 02/12/2014...

  • Page 86: Environmental Information

    By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects on the environment and human health. Mercury Notice This Barco product consists of materials that may contain mercury, which must be recycled or disposed of in accordance with local, state, or country laws: • Within this system, the lamp in the projector contains mercury.
  • Page 87 16.Environmental information 本产品中包含的有毒有害物质/成分的名称和含量。 RLS W12 02/12/2014...

Table of Contents