Download Print this page

Reinstall Bottom Vent; Complete Installation - KitchenAid 9759536B Installation Instructions Manual

Kitchenaid appliances 30"(76.2cm) classic commercial style dual fuel convection range installation instructions
Hide thumbs

Advertisement

Adjust Flame Height
Adjust the height of top burner flames. The cooktop "low" burner
flame should be a steady blue flame approximately ¼" (0.64 cm)
high.
A
B
A. Low flame
B. High flame
The flame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
A. Adjustment screw
If the "low" flame needs to be adjusted:
1. Remove the control knob.
2. Hold the knob stem with a pair of pliers. Use a small flat-
blade screwdriver to turn the screw located in the center of
the control knob stem until the flame is the proper size.
3. Replace the control knob.
4. Test the flame by turning the control from "LO" to "HI,"
checking the flame at each setting.
Check Operation of Oven Element
1. Turn oven selector to BAKE. Default temperature appears in
the temperature display.
2. Press ENTER. The first preheat light comes on when the oven
temperature begins to rise.
3. When the second preheat light comes on, open oven door
and hold hand above oven floor and feel for heat. Do not
touch oven floor. Press CANCEL and turn oven selector to
RESET.
Check Operation of Oven Broil Element
1. Close the oven door.
2. Turn oven selector to BROIL. "HI" will appear in the
temperature display.
3. Press ENTER. Look through oven window. The top element
should glow red, and heat should be radiating out of the door.
Press CANCEL and turn oven selector to RESET.
12
A
If oven does not operate:
Check that power supply is turned on.
Check that the range is plugged in and the circuit breaker has
not tripped or the household fuse has not blown.
Repeat start-up. If the oven still does not operate at this point,
contact your dealer or authorized service company for
assistance.
Install Burner Grates
Place burner grates over burner caps. The simmer plate may sit
on one of the grates or be stored for future use.

Reinstall Bottom Vent

1. Insert lower vent tabs into the slots on the front trim.
2. Push vent upward until the holes line up at top of vent.
3. Reattach the vent using the 4 screws.
A
A. Bottom vent
B. Reattach these screws.

Complete Installation

1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Dispose of/recycle all packaging materials.
3. Check that range is correctly positioned in countertop cutout
and that the range is level. See "Level Range."
4. Check that the specified distances to cabinet surfaces were
maintained. See "Location Requirements."
5. Check that burner caps are positioned properly on sealed
burner bases.
6. Check that backguard or island trim is installed. (If horizontal
clearance to combustible materials behind cooking surface is
less than 1" [2.5 cm]).
7. Check that the range is connected only to the type of gas for
which it is certified for use.
8. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by shipping material.
Dry thoroughly with a soft cloth. For more information, see
the "Range Care" section of the Use and Care Guide.
9. Read "Range Use" in the Use and Care Guide.
10. Turn on surface burners and oven. See the Use and Care
Guide for specific instruction on range operation.
If range does not operate, check the following:
Household fuse has not blown, or circuit breaker has not
tripped.
Gas valves are turned to the "open" position.
If the gas supply line shutoff valve is open, turn to "closed"
and contact a qualified technician.
Electrical supply is connected.
See "Troubleshooting" in the Use and Care Guide.
B

Advertisement

loading

  Related Manuals for KitchenAid 9759536B