Advertisement
Dl
This appliance should be connected
H directly to the fused disconnect
(or
circuit breaker box) through flexible, armored or
non-metallic
sheathed, copper cable (with
grounding wire). The flexible armored cable
from the appliance should be connected directly
to the junction box.
El
Locate the junction box to allow as
.
much slack in the cable as Dossible
between the junction box and the appliance so
that the oven can be moved if servicing is ever
necessary.
Do Not cut the conduit.
El
A U.L.-listed conduit connector
must
H be provided at the junction box.
A wiring diagram is included in the
Tech Sheet. The Tech Sheet is located
behind the control panel.
Electrical
connection
Electrical Shock Hazard
l
Electrical ground is required on this
appliance.
l
Do Not connect to the electrical supply
until appliance is permanently
grounded.
l
Disconnect power to the junction box
before making the electrical
connection.
l
This appliance must be connected to a
grounded, metallic, permanent wiring
system, or a grounding connector
should be connected to the grounding
terminal or wire lead on the appliance.
Failure to do so could result in a fire,
personal injury or electrical shock.
This appliance is manufactured
with white
(neutral) power supply wire and a cabinet-
connected green grounding wire twisted
together.
Connect the appliance cable to the junction box
through the U.L.-listed conduit connector.
Complete electrical connection
according to
local codes and ordinances.
A. Where local codes permit...
connecting the cabinet-grounding
conductor
to the neutral (white) junction
box wire:
Junction
box \
Cable from
power supply
Bare or/
green wire
Figure 1
Cable
from ov
I
conduit
connector
en
Grounded Neutral
1. Disconnect the power supply.
2.
Remove the terminal block cover.
3. Connect together 3 wires: green and white
appliance cable wires and the neutral (white)
wire in junction box.
4. Connect the two black wires together; then
the two red wires together. See Figure 1.
B. Where local codes Do Not
permit...
connecting the cabinet-grounding
conductor
to the neutral (white) junction box wire:
Cable from
from oven
connector
Figure 2
Ungrounded Neutral
1. Disconnect power supply.
2. Separate the green and white appliance
cable wires.
3. Connect the white appliance cable wire to the
neutral (white) wire in the junction box.
4. Connect the two black wires together; then
the two red wires together. See Figure 2.
5. Connect the green or bare grounding wire
from the appliance cable to a grounded wire in
the junction box.
C. If connecting
to a four-
wire electrical
system...
Do Not connect the cabinet-grounding
conductor to the neutral (white) junction
box wire.
Cable from
conduit
Figure 3
connector
1. Disconnect the power supply.
2. Separate the green (or bare) and white
appliance cable wires.
3. Connect the white appliance cable wire to the
neutral (white) wire in the junction box.
4. Connect the two black wires together; then
the two red wires together. See Figure 3.
5. Connect the green appliance cable wire to
the green grounding wire in the junction box.
Now start...
With oven in kitchen.
Remove shipping materials, tape, and
protective film from oven.
Do Not
remove shipping base at this time.
121
Remove the racks and other parts
.
from inside both ovens.
Personal Injury/Product
Damage Hazard
l
Use both hands to remove oven doors.
l
Grasp only the sides of oven doors.
l
Do Not use handle or any portion of the
trim for lifting.
l
Because of the weight and size of the
oven, two or more people are needed to
move and safely install the oven.
Failure to properly grasp the oven doors
or to lift ovens properly could result in
1 damage to the product or personal injury.
131
n
Completely open the lower oven door.
Remove the two oven door screws. (Not
all models have oven door screws.)
screw
141
n
Close lower oven door to the broil position.
Grasp the sides of the oven door and pull the
door up and out of the hinge slots to remove
Set door aside.
151
Repeat Steps 3 and 4 for upper oven
n
door.
Product Damage
Before moving oven across floor, check
that oven is on shipping base or slide
oven onto cardboard or hardboard.
Failure to follow these instructions
may
result in damage to floor covering.
161
Turn power supply off. Move oven close
n
to final position. Remove and discard
shipping base. Feed appliance cable through the
opening in cabinet. Make electrical connection.
See "Electrical requirements"
and "Electrical
connection"
sections, Panels A and B.
Panel B
Advertisement
