Download Print this page

Tools Needed - KitchenAid 3187360 Installation Instructions

Electric built-in 27” thermal convection double oven
Hide thumbs

Advertisement

Cabinet
door
'Note:
There must be 1"
min. between
bottom
of
cabinet
door and top of
oven console.
2-l/2'
min.
Oven control
Before you start...
Read the electrical and carpentry
instructions.
Proper installation
is your responsibility.
A
qualified technician
should install this oven.
Make sure you have everything
necessary for
correct installation.
It is the responsibility
of the
installer to comply with the installation
clearances specified on the serial/rating
plate.
The serial/rating
plate can be found behind the
upper oven door on the frame of the oven.
Check location
where the built-in oven will be
installed. The location should be away from
strong draft areas, such as windows, doors, and
strong heating vents. The built-in oven should
be located for convenient
use in the kitchen.
Cabinet opening dimensions
that are shown
must be used. Given dimensions
provide
minimum clearance. Contact surface must be
solid and level and flush with the bottom.
The recessed installation
area
must provide
complete enclosure around the recessed portion
of the oven.
ALL OPENINGS
IN THE WALL OR FLOOR
WHERE THE BUILT-IN OVEN IS TO BE
INSTALLED
MUST BE SEALED.
Electrical ground
is required. See "Electrical
requirements."
r
See Note.'
r
c"-- --
1
-4,
I
I
I
I
i
I
!
I
v'--' \
\
Do Not
\
seal oven
\
to cabinets.
.
cabinet
recessed
width
See Note:
depth
4*
I
cabinet
I
opening
height
i
I
I
46-l 3/l 6"-
recessed
height
\
24' min. overall
cabinet
depth
Electrical Shock Hazard
lt is the customer's responsibility:
l
To contact a qualified electrical installer.
l
To assure that the electrical installation
is adequate and in conformance with
National Electrical Code, ANSVNFPA
70-
latest edition**, and all local codes
and ordinances.
Failure to do so could result in fire, .
electrical shock or other personal Injury.
Personal Injury Hazard
Securely fasten oven to cabinet using the
4 screws provided.
Failure to do so could cause the oven to
move
or tip during use and result in
personal iniurv.
upper oven door,
when open, is
36" from floor.
NOTE:
NOTE:
The oven support surface must be flush
with the bottom of the cabinet cutout.
Clearances specified are for combustible
walls and materials that have a density of
20 or more pounds per cubic foot. No
evaluation has been made for
installations
adjacent to materials that are
less than 20 pounds per cu. ft. or to
plastic tiles and sheeting.
Tools needed
Electrical
for installation:
requirements
IA.J
This appliance
must
be connected to
the proper electrical voltage and
frequency as specified on the serial/rating
plate
located behind the oven door on the front frame.
A fuse is required in both sides of the line. A
time-delay fuse is recommended.
Use the
voltage and kilowatt rating given on seriavrating
plate to select the proper fuse size.
Electrical Shock Hazard
l
Electrical ground is required on this
appliance.
l
If cold water pipe is interrupted by plastic,
non-metallic gaskets, or other insulating
materials, Do Not use for grounding.
l
Do Not ground to a gas pipe.
l
Do Not have a fuse in the neutral or
grounding circuit. A fuse in the neutral or
grounding circuit could result in an
electrical shock.
l
Do Not use an extension cord with this
appliance.
l
Check with a qualified electrician if you
are in doubt as to whether the appliance
is properly grounded.
Failure to follow these instructions
could result in serious injury or death.
If codes permit and a separate grounding
wire is used, it is recommended that a
qualified electrician determine that the
grounding path is adequate.
Save Installation Instructions
for the local
river
Fuse Requirements
120/208 Volts
Kilowatts
Fuse Size (amps)
6.2
30
Parts su Dplied
for insta lation:
6.2 to 8.3
40
8.3 to 10.4
50
120/240 Volts
Kilowatts
Fuse Size (amps)
7.2
30
7.2 to 9.6
40
9.6 to 12.0
50
IBI
OVEN MUST BE CONNECTED
n
WITH COPPER WIRE ONLY.
la
n
Wire sizes and connections
must
conform to the requirements
of the
National Electrical Code, ANSI/NFPA
70 - latest
edition**, and all local codes and ordinances.
Wires sizes and connections
must conform with
the rating of the appliance.
Copies of the standards listed may be obtained
from:
**National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Panel A

Advertisement

loading

  Related Manuals for KitchenAid 3187360