Programmed Play - Sanyo DC-DA1100 Instruction Manual

CD PLAY
Use compact discs bearing the symbol shown in Fig. 6. In addition to
conventional 12 cm CDs, this system can be used to play 8 cm CDs
without an adapter.
- This unit can play back the CD-R/RW that have recorded music data
as well. However, some CD-R/RWs can not be played back depend-
ing on the recording conditions.
- The CD-R/RW can't be recorded in this unit.
1. Press the FUNCTION button to select "CD" function.
2. Press the CD compartment lid (Q CD OPEN/CLOSE portion). The
CD compartment opens.
3. Place the disc with the label facing up on the disc tray (Fig. 7). (Place
only one disc at a time.)
4. Press the CD compartment lid (Q CD OPEN/CLOSE portion) to close
it. The total number of tracks and total playing time on the disc appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, "Cd" appears. If this occurs, load the disc
correctly or replace the damaged disc.
5. Press the I button. Play starts from the first track.
The current track number and elapsed playing time are displayed.
6. Press the N button to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the N button and wait for the disc to stop rotating before
opening the disc compartment.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high tem-
peratures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing sur-
face of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic sprays
or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the E or F button, then press the I
button.
Using the remote control
Press two number buttons within 4 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the I button. " a " blinks on the display. To resume play, press
the button again.
Skip play
To skip to track 6 while track 3 is playing, press the E button repeat-
edly until "6" appears (in the track section) on the display. To skip back to
track 3 while track 6 is playing, press the F button repeatedly until "3"
appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the E or F button is pressed during play, the player will search at
high speed in the forward or reverse direction while the button is being
pressed. When the button is released, normal play will continue.
7
Repeat play (Remote control only)
Press the FM MODE/REPEAT button before or during play. The player
will play all the tracks or all the programmed tracks repeatedly. "
appears on the display. To cancel repeat play, press the FM MODE/
REPEAT button again. "

PROGRAMMED PLAY

Up to 20 tracks on a disc can be programmed for play in any order.
- First, select "CD" function and load a disc that you want to programme.
- The tracks must be programmed in the stop mode.
- The same track can be programmed more than once.
1. Press the MEMORY button.
2. Select a track by using the E or F button.
- The number buttons on the remote control can also be used.
3. Press the MEMORY button.
4. Repeat steps 2 - 3 to programme additional tracks.
5. Press the I button to start programmed play.
When all programmed tracks have been played, the player stops
automatically.
- The programme contents are retained in memory.
- Any attempt to programme more than 20 tracks will result in "FULL"
being displayed and discontinuation of the programming.
- The programme contents are retained even if the function selection
is changed. After selecting "CD" function press the MEMORY button.
The programmed contents appear.
- To cancel programmed play, press the N button twice.
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the pro-
grammed details sequentially appear on the display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY button repeatedly until "- - . - -
- -" is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track:
1. In the stop mode, press the MEMORY button repeatedly until the
track number to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
" disappears.
"