Table of Contents
Advertisement
Inserting batteries (Fig. 2)
Note:
Always remove batteries if the remote control is not to be used for a
month or more. Batteries left in the unit may leak and cause damage.
Remote control range (Fig. 4)
The buttons on the remote control perform similar functions to similarly
marked buttons on the front panel.
GENERAL OPERATION
Turning the power on and off
To turn the power on, press the power button and the display lights.
To turn the power off, press the power button again, the display goes out.
Selecting the function
Press the FUNCTION button to select the desired function as follows
display shows.
Cd v TAPE v TU v LInE v Cd v ...
The function is automatically selected when CD play or type playback is
started or when the TUNER/BAND button has been pressed (except
during recording).
-
When the function selection is changed, CD play or tape playback is
automatically stopped.
Adjusting the volume
Turn the VOLUME control, (or press the + or - VOLUME button on the
remote control). The volume level appears on the display. (VOL 0 ~ VOL
40)
Surround sound button
Press the SURROUND button, "SURR" appears on the display and a 3
dimensional sound effect is created.
Bass expander button
Press the BASS button to enhance the bass sound.
"BASS" appears on the display.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
CLASSIC: Classical music, etc.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Press the CD button on the unit for at least 30 seconds.
3. Connect the mains lead.
4. Operate the unit.
CD PLAY
Use compact discs bearing the symbol shown in Fig. 6. In addition to
conventional 12 cm CDs, this system can be used to play 8 cm CDs
without an adapter.
1. Press the FUNCTION button to select "CD" function.
2. Press the CD compartment lid (q CD OPEN/CLOSE portion). The
CD compartment opens.
3. Place the disc with the label facing up on the disc turntable (Fig. 6).
(Place only one disc at a time.)
4. Press the CD compartment lid (q CD OPEN/ CLOSE portion) to
close it.
The total number of tracks and total playing time on the disc appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, "Cd" appears. If this occurs, load the disc
correctly or replace the damaged disc.
5
5. Press the CD button. Play starts from the first track.
The current track number and elapsed playing time are displayed.
6. Press the N button to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the N button and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
-
Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
-
Discs should be returned to their cases after use.
-
Do not apply paper or write anything on the disc surface.
-
Handle the disc by its edge. Do not touch the playing surface (glossy
side).
-
Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
-
Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the F or E button, then press the Ak
button.
Using the remote control
Press two number buttons within 2 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the CD button. " a " blinks on the display. To resume play, press
the button again.
Skip play
To skip to track 6 while track 3 is playing, press the E button repeatedly
until "6" appears (in the track section) on the display. To skip back to track
3 while track 6 is playing, press the F button repeatedly until "3"
appears.
-
The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the F or E button is pressed during play, the player will search at
high speed in the forward or reverse direction while the button is being
pressed. When the button is released, normal play will continue.
Repeat play
Press the REPEAT button before or during play. The player will play all
the tracks or all the programmed tracks repeatedly. "
cancel repeat play, press the REPEAT button again. "
PROGRAMMED PLAY
Up to 24 tracks on a disc can be programmed for play in any order.
-
First, select "CD" function and load a disc that you want to programme.
-
The tracks must be programmed in the stop mode.
-
The same track can be programmed more than once.
1. Press the MEMORY button on the remote control.
" appears. To
"disappears.
Advertisement
Table of Contents
