Programmed Play - Sanyo DC-DA280 Instruction Manual

Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system
can be used to play 8 cm CDs without an adapter.
1. Press the FUNCTION button to select "CD" function.
2. Press the CD compartment lid (q CD OPEN/CLOSE portion). The
CD compartment opens.
3. Place the disc with the label
facing up on the disc turntable.
(Place only one disc at a time.)
4. Press the CD compartment lid
(q CD OPEN/ CLOSE portion)
to close it.
The total number of tracks and
total playing time on the disc
appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, "Cd" appears. If this occurs, load the disc
correctly or replace the damaged disc.
5. Press the CD button. Play starts from the first track.
The current track number and
elapsed playing time are
displayed.
6. Press the N button to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the N button and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the F or E button, then press the CD
button.
Using the remote control
Press two number buttons within 2 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the CD button (or i button on the remote control). " a " blinks
on the display. To resume play, press the button again.
Skip play
To skip to track 6 while track 3 is playing, press the E button repeatedly
until "6" appears (in the track section) on the display. To skip back to track
3 while track 6 is playing, press the F button repeatedly until "3"
appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
CD PLAY
Search (forward/reverse)
If the E or F button is pressed during play, the player will search at
high speed in the forward or reverse direction while the button is being
pressed. When the button is released, normal play will continue.
Repeat play (Remote control only)
Press the REPEAT/FM MODE button before or during play. The player
will play all the tracks or all the programmed tracks repeatedly. "
appears. To cancel repeat play, press the REPEAT/FM MODE button
again. " "disappears.

PROGRAMMED PLAY

Up to 24 tracks on a disc can be programmed for play in any order.
- First, select "CD" function and load a disc that you want to programme.
- The tracks must be programmed in the stop mode.
- The same track can be programmed more than once.
1. Press the MEMORY button
on the remote control.
2. Select a track by using the
E or F button.
- The number buttons on
the remote control can
also be used.
3. Press the MEMORY button on the remote control.
4. Repeat steps 2-3 to programme additional tracks.
5. Press the CD button to start programmed play.
When all programmed tracks have played, the player stops
automatically.
- The programme contents are retained in memory.
- Any attempt to programme more than 24 tracks will result in "FULL"
being displayed and discontinuation of the programming.
- To cancel programmed play, press the N button twice.
Checking the programme (Remote control only)
Each time the MEMORY button is pressed in the stop mode, the
programmed details sequentially appear on the display.
Changing a programme
To add a new track to a programme: (Remote control only)
1. In the stop mode, press the MEMORY button repeatedly until
"- - - - - -" is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track: (Remote control only)
1. In the stop mode, press the MEMORY button repeatedly until the
track number to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
-4-
"