Normal Play; Programmed Play - Sanyo DC-X801 Instruction Manual

Stereo sound system belt drive turntable
Table of Contents

Advertisement

CD PLAY
NORMAL PLAY
1. Press the PLAY/PAUSE switch. The PLAY indicator illu-
minates and the first selection (TRACK no.1) will begin
playing.
The CD display indicates the track no. which is playing.
2. Adjust the volume, BALANCE and GRAPHIC EQUAL-
IZER controls to the desired sound level and sound
equalization.
3. Press the STOP switch to stop play at any time.
4. When the last track has played, the player will go to stop
mode. The display indicates "0".
5. When play is finished, open the disc tray, remove the
disc, close the disc tray.
When the OPEN/CLOSE switch is pressed during play,
play will stop and the disc tray will come out.
Pause
When the PLAY/PAUSE switch is pressed during play, the
player will go to pause mode. (The PLAY indicator flashes.)
In order to cancel pause, press the PLAY/PAUSE switch
once again, and play will begin from where it had stopped.
Track search
When the Of•li
to*
or 44/ 44 skip/search switch is pressed
during play, the player will quickly advance or reverse while
the switch is being pressed. When the switch is released,
play will begin again at that point.
- If track search is performed during pause, the player will
return to pause when that switch is released.
- During track search operation, the display indicates the
elapsed playing time of the track which is searching. The
left-hand digit indicates the last place of minutes and the
right-hand digit indicates ten's place of seconds.
eg. 15:30 = 5.3, 1:32 = 1.3
Track skip
By using the skip mode during play, the beginning of
desired tracks can easily be found. The number of the track
to be searched is displayed on the display.
Press the 0404 , or 44/ 44 skip/search switch with
one touch (or if required, repeatedly) until the desired track
no. is displayed. The player will start playing from the
desired track.
- The track no. will change every time by pressing the
skip/search switch.
- If in pause before pressing the skip/search switch, the
player will go to pause (standby) after beginning of the
track is located.
Direct track selection play
Using the track number (0 - 9 and +10) buttons on the
remote controller, play can be started immediately from the
desired track.
While a disc is being played, it is possible to switch imme-
diately to a particular track.
Examples:
To play from the track 3 on the disc, press button 3.
To play from the track 10, press +10 and then 0.
To play from the track 25, press +10 twice and then 5.
Play can also be started by selecting the track number
using one of the skip/search buttons (
/N or t.i./
io,o; ) and pressing the play/pause (
is) button. When
using the controls on the main unit, select the track
number using the skip/search switch and then press the
PLAY/PAUSE switch.
A track number greater than the number of tracks on the
disc is not selected.
- This operation is not possible during programmed play.
Random play (automatic programmed play by microcom-
puter)
When the RANDOM button on the remote confer is
pressed, the PLAY and RANDOM indicators illuminate and
the tracks on the disc will be played automaticaN at
random by the microcomputer.
- Random play results when the RANDOM btrcrl s pres
s
ed
during normal play.
- When the RANDOM button is pressed durreg random
play, operation moves to the next random prog-ammed
track.
- This operation is not possible during prograr=ed
Repeated play
When the REPEAT switch is pressed dung
REPEAT indicator illuminates. The player 'Al pay
the
tracks, all the programmed tracks or the 7 - a n=
tracks repeatedly.
To cancel repeated play, press the REPEAT stivit corra
again. (The REPEAT indicator goes out) Whew: the STa?
or OPEN/CLOSE switch is pressed, the repeated =Eatlor 04.21
be cancelled.
PROGRAMMED PLAY
The tracks (up to 16) on a disc can be played in army dte§r=.
sequence whatsoever.
- The same tracks can be programmed ever and z.i-er
again.
- Make sure that the CD player is in the nr a step 7ode.
If not, press the STOP switch of the CD aaier.
Programming procedure (using the remote corn fro:'
Example:
Programming play in the sequence of tracks 5, 2, 6 and 10
1. Press the MEMO button. The PROG. indicator Elurni-
nates and track number "1" flashes on the CD display.
2. Set track 5 which is to be played first by pressing the
track number button 5. "5" flashes.
3. Press the MEMO button. "5" illuminates.
4. Set track 2 which is to be played second by pressing the
button 2. "2" flashes.
5. Press the MEMO button. "2" illuminates. The PROG.
indicator remains illuminated.
The remaining tracks are programmed in the same way.
- The tracks can also be selected using the skip/search
button.
- When programming using the controls on the main unit,
use the skip/search and MEMORY/CHECK switches.
- Any attempt to programme more than 16 tracks will
result in discontinuation of the programming.
-5-

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Tp-x801

Table of Contents