National DC5-163 Instructions Manual page 12

Introduction
This NEC PCI to USB 2.0 Host Controller card is compliant with the Universal Serial Bus Specification Revision 2.0 and
Open Host Controller Interface Specification for low-speed (1.5Mbps) / full-speed (12Mbps) speed signaling and Enhanced
Host Controller Interface Specification for high-speed signaling (480Mbps).
Features
•
Using NEC (uPD720100) PCI to USB 2.0 Host Controller chip
•
Compliant with Universal Serial Bus Specification Revision 2.0
•
Compliant with Open Host Controller Interface Specification for USB Rev 1.0a
•
Complaint with Enhanced Host Controller Interface Specification for USB Rev 0.95
•
32-bit 33 MHz Host Interface compliant to PCI Specification release 2.2
•
Supports PCI-Bus Power Management Interface Specification release 1.1
•
PCI bus-master access
•
PCI multi-function device consists of two OHCI Host Controller cores for full-speed / low-speed signaling and one EHCI
Host Controller cores for high-speed signaling.
•
All downstream forcing ports can handle high-speed (480Mbps), full-speed (12Mbps), and low-speed (1.5Mbps)
transaction
•
Provides five type 'A' downstream ports for USB device connections
•
Full support of real time dynamic insertion and removal of devices
•
Supports all USB-compliant peripherals (e.g. keyboard, mouse, monitor, telephone, joystick, etc.)
•
Driver support for Windows 98, 98SE, ME, 2000 & XP operating system
Installing the NEC PCI to USB 2.0 Host Controller card
Installing the NEC PCI to USB 2.0 Host Controller card into your computer is a simple process. Please follow these steps:
1. Turn off your computer and all external devices connected to it.
2. Disconnect your computer from the power sources.
3. Open the computer case. Refer to your computer user manual for more details.
4. Find an available PCI slot and remove the slot bracket. Save the bracket screw for later use.
5. Align the NEC PCI to USB 2.0 Host Controller card horizontally with respect to the PCI slot and insert it into the slot
firmly and evenly. Take care not to force it into the slot. Once you have properly positioned the NEC PCI to USB 2.0
Host Controller card into the slot, fasten it to the computer case with the bracket screw you have saved.
6. Secure the computer case and switch on your computer.
Installing Windows 98/98SE/ME/2000/XP driver
This NEC PCI to USB 2.0 Host Controller card require these two drivers in order to function properly. These drivers are:
1. "NEC USB Open Host Controller" drivers
For the two "NEC USB Open Host Controller", no additional driver required. Full driver support by Microsoft Open HCI
based drivers. Simply have your Windows O/S Installation CD ready when Windows Installation Wizard prompts for the
location of the driver.
2. "NEC PCI to USB Enhanced Host Controller" driver
For the "NEC PCI to USB Enhanced Host Controller", the driver is located in the Driver CD that came with the card. When
Windows Installation Wizard detects this device "PCI Universal Serial Bus", insert the Driver CD in to the CDROM drive and
go to this directory – D:\NEC\uPD720100 (Assuming drive D is your CDROM drive) to install the driver.
After you have installed the driver, go to the Device Manager to check if you have properly installed the driver. Under
"Universal Serial Bus Controller" in Device Manager, there are five items added.
NEC PCI to USB Enhanced Host Controller
NEC USB Open Host Controller
NEC USB Open Host Controller
USB Root Hub
USB Root Hub
If you have these five items added in to the Device Manager and there is no exclamation mark next to the item then you have
installed the NEC PCI to USB 2.0 Host Controller card properly and the card is ready for use!
NEC PCI USB 2.0 U s e r M a n u a l
For use with Moticam 1000, Moticam 2000, DC4 and DC5 Series
SD-NECUSB20-031001