Yamaha MCX-CA15 Owner's Manual page 79

You can manually configure the client to conform
with the settings of an existing network. Manual
client settings are only necessary if you are also
using a manual configuration for the server. In most
cases, Auto Configuration is adequate for using the
MusicCAST system.
When making manual settings, it is not always
necessary to set all of the parameters described in
the following section. The settings you make will
depend on the network to which the client is
connected. However, be sure to set the following:
Server ID
IP address for the client (when DHCP is set to
OFF)
Subnet mask*
*
The server and client will only function
correctly if they are under the same subnet
(running under one or more hubs).
Before performing Manual Configuration, be sure
to:
Complete all connections for the client and its
companion components and tum on the client.
Upgrade the MusicCAST system firmware on
the server.
Tum on the server.
Set the client ID for each client connected to the
MusicCAST system on the server. For details,
see the MCX-I000 Owner's Manual, page 113.
Set the Subnet Mask address on the server. (This
must be the same for both the server and the
client.) For details, see the MCX-I000 Owner's
Manual, page 109.
You must perform the Manual Configuration
procedure if your MusicCAST system uses more
than one server.
CONFIGURING THE CLIENT
1
Press and hold MENU until the Top
Menu screen is displayed.
2
Press
A
I
v
to choose "Setup" and
press SELECT.
Ed
j.
t. Book p·lar·k
:irSEft..iJP
3
Press
A
I
v
to choose IINetwork ll and
press SELECT.
4
Press
A
I
v to choose IIManual Setupll
and press SELECT.
Set the desired settings.
• Setting the server 10
You can manually specify the ID of the server you
want to connect to.
You must enter the server ID exactly as it appears on
the server. To view the server's ID, see the MCX-
1000 Owner's Manual, page 112.
1
Select "Setup" > "Network" > "Manual
Setup" from the Top Menu.
2
Press
A
I
v
to choose "Server 10" and
press SELECT.
T
Ser·i.}er· I D
DHCP
3
Press> to move the cursor to the server
10 field and press SELECT.
... [51.)-(1(1(11 ]
Save&NetMc~k
restart
Cancel
25
You can manually configure the client to conform
with the settings of an existing network. Manual
client settings are only necessary if you are also
using a manual configuration for the server. In most
cases, Auto Configuration is adequate for using the
MusicCAST system.
When making manual settings, it is not always
necessary to set all of the parameters described in
the following section. The settings you make will
depend on the network to which the client is
connected. However, be sure to set the following:
Server ID
IP address for the client (when DHCP is set to
OFF)
Subnet mask*
*
The server and client will only function
correctly if they are under the same subnet
(running under one or more hubs).
Before performing Manual Configuration, be sure
to:
Complete all connections for the client and its
companion components and tum on the client.
Upgrade the MusicCAST system firmware on
the server.
Tum on the server.
Set the client ID for each client connected to the
MusicCAST system on the server. For details,
see the MCX-I000 Owner's Manual, page 113.
Set the Subnet Mask address on the server. (This
must be the same for both the server and the
client.) For details, see the MCX-I000 Owner's
Manual, page 109.
You must perform the Manual Configuration
procedure if your MusicCAST system uses more
than one server.
CONFIGURING THE CLIENT
1
Press and hold MENU until the Top
Menu screen is displayed.
2
Press
A
I
v
to choose "Setup" and
press SELECT.
Ed
j.
t. Book p·lar·k
:irSEft..iJP
3
Press
A
I
v
to choose IINetwork ll and
press SELECT.
4
Press
A
I
v to choose IIManual Setupll
and press SELECT.
Set the desired settings.
• Setting the server 10
You can manually specify the ID of the server you
want to connect to.
You must enter the server ID exactly as it appears on
the server. To view the server's ID, see the MCX-
1000 Owner's Manual, page 112.
1
Select "Setup" > "Network" > "Manual
Setup" from the Top Menu.
2
Press
A
I
v
to choose "Server 10" and
press SELECT.
T
Ser·i.}er· I D
DHCP
3
Press> to move the cursor to the server
10 field and press SELECT.
... [51.)-(1(1(11 ]
Save&NetMc~k
restart
Cancel
25