1. Manuals
  2. Brands
  3. Allied Telesis Manuals
  4. Network Router
  5. AT-9408LC/SP Series
  6. Installation manual

Allied Telesis AT-9408LC/SP Installation Manual

At-9400 series layer 2+ gigabit ethernet switches
Hide thumbs Also See for AT-9408LC/SP:
Table of Contents

Advertisement

Quick Links

◆

Installation Guide

613-000357 Rev. B
AT-9400 Series
Layer 2+ Gigabit
Ethernet Switches
AT-9408LC/SP
AT-9424T/GB
AT-9424T/SP
AT-9424Ts
AT-9424Ts/XP
AT-9448Ts
AT-9448T/SP
AT-9448Ts/XP

Advertisement

Table of Contents
loading

Related Manuals for Allied Telesis AT-9408LC/SP

Summary of Contents for Allied Telesis AT-9408LC/SP

  • Page 1: Installation Guide

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches AT-9408LC/SP AT-9424T/GB AT-9424T/SP AT-9424Ts AT-9424Ts/XP AT-9448Ts AT-9448T/SP AT-9448Ts/XP ◆ Installation Guide 613-000357 Rev. B...
  • Page 2 Copyright © 2006 Allied Telesyn, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Microsoft and Internet Explorer are registered trademarks of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape Communications Corporation.

  • Page 3: Electrical Safety And Emissions Standards

    Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Radiated Energy Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules.
  • Page 4 Translated Safety Statements Important: Appendix B contains translated safety statements for installing this equipment. When you see the , go to Appendix B for the translated safety statement in your language. Wichtig: Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Wenn sehen, schlagen Sie in Anhang B den übersetzten Sicherheitshinweis in Ihrer Sprache nach.

  • Page 5: Table Of Contents

    Returning Products............................. 10 Sales or Corporate Information ........................10 Management Software Updates ......................... 10 Chapter 1 Overview ..........................................11 Description ...............................12 AT-9408LC/SP Switch..........................12 AT-9424T/GB Switch..........................13 AT-9424T/SP Switch ..........................14 AT-9424Ts Switch ............................15 AT-9424Ts/XP Switch ..........................16 AT-9448Ts Switch ............................17 AT-9448T/SP Switch ..........................
  • Page 6 Environmental Specifications ...........................69 Power Specifications ............................70 Certifications ..............................70 RJ-45 Twisted Pair Port Pinouts ........................71 AT-9408LC/SP Switch 1000Base-SX Port Specifications ................73 RJ-45 Style Serial Terminal Port Pinouts ......................74 RPS 21-pin D-combo Port and Connector Pinouts ..................74 Appendix B Translated Safety Statements ................................77...

  • Page 7: Preface

    Preface This guide contains the installation instructions for the AT-9400 Layer 2+ Gigabit Ethernet Series switches. This preface contains the following sections: “Safety Symbols Used in this Document” on page 8 “Where to Find Web-based Guides” on page 9 “Contacting Allied Telesyn” on page 10 Note For a list of features, refer to Appendix C, “Features and Standards,”...

  • Page 8: Safety Symbols Used In This Document

    Preface Safety Symbols Used in this Document This document uses the safety symbols defined in Table 1. Table 1. Safety Symbols Symbol Meaning Description Caution Performing or omitting a specific action may result in equipment damage or loss of data. Warning Performing or omitting a specific action may result in electrical shock.

  • Page 9: Where To Find Web-Based Guides

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Where to Find Web-based Guides The installation and user guides for all Allied Telesyn products are available in portable document format (PDF) on our web site at www.alliedtelesyn.com. You can view the documents online or download them onto a local workstation or server.

  • Page 10: Contacting Allied Telesyn

    Preface Contacting Allied Telesyn This section provides Allied Telesyn contact information for technical support as well as sales and corporate information. Online Support You can request technical support online by accessing the Allied Telesyn Knowledge Base: http://kb.alliedtelesyn.com. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions.

  • Page 11: Chapter 1 Overview

    The AT-9400 Series switches are managed, Layer 2+ Gigabit Ethernet switches that offer a wide range of features and capabilities for Ethernet, Fast Ethernet, and Gigabit Ethernet networks. The models in the AT-9400 Series are: AT-9408LC/SP AT-9424T/GB AT-9424T/SP AT-9424Ts AT-9424Ts/XP...

  • Page 12: Description

    Status LEDs for the ports, SFP transceiver slots, and system Redundant power supply (RPS) connector Compact flash card slot Figure 1 shows the front and back panels of the AT-9408LC/SP switch. SFP Transceiver Slots 1000Base-SX Fiber Optic Ports System LEDs...

  • Page 13: At-9424T/Gb Switch

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide AT-9424T/GB The AT-9424T/GB has the following features: Switch 24 10/100/1000Base-T ports Two gigabit interface connector (GBIC) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management Status LEDs for the ports, transceiver slots, and system Redundant power supply connector Figure 2 shows the front and back panels of the AT-9424T/GB switch.

  • Page 14: At-9424T/Sp Switch

    Chapter 1: Overview AT-9424T/SP The AT-9424T/SP switch has the following features: Switch 24 10/100/1000Base-T ports Two Gigabit Ethernet small form-factor pluggable (SFP) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management Status LEDs for the ports, transceiver slots, and system Redundant power supply connector Figure 3 shows the front and back panels of the AT-9424T/SP switch.

  • Page 15: At-9424Ts Switch

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide AT-9424Ts The AT-9424Ts switch features: Switch 24 10/100/1000Base-T ports Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management Status LEDs for the ports, transceiver slots, and system Redundant power supply connector Compact flash card slot Figure 4 shows the front and back panels of the AT-9424Ts switch.

  • Page 16: At-9424Ts/Xp Switch

    Chapter 1: Overview AT-9424Ts/XP The AT-9424Ts/XP switch features: Switch 24 10/100/1000Base-T ports Four Gigabit Ethernet small form-factor pluggable (SFP) transceiver slots Two 10 Gigabit Ethernet small form factor pluggable (XFP) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management Status LEDs for the ports, transceiver slots, and system Redundant power supply connector Compact flash card slot...

  • Page 17: At-9448Ts Switch

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide AT-9448Ts The AT-9448Ts switch has the following features: Switch 48 10/100/1000Base-T ports An RJ-45 style serial terminal port for local (out-of-band) management Status LEDs for the ports, transceiver slots, and system Redundant power supply connector Compact flash card slot Expansion slot...

  • Page 18: At-9448T/Sp Switch

    Chapter 1: Overview AT-9448T/SP The AT-9448T/SP switch features: Switch 48 10/100/1000Base-T ports Four Gigabit Ethernet SFP transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management. Status LEDs for the ports, transceiver slots, and system Redundant power supply (RPS) connector Compact flash card slot Figure 7 shows the front and back panels of the AT-9448T/SP switch.

  • Page 19: At-9448Ts/Xp Switch

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide AT-9448Ts/XP The AT-9448Ts/XP switches features: Switch 48 10/100/1000Base-T ports Two 10 Gigabit Ethernet small form factor pluggable (XFP) transceiver slots An RJ-45 style serial terminal port for local (out-of-band) management Status LEDs for the ports, transceiver slots, and system Redundant power supply connector Compact flash card slot Expansion slot...

  • Page 20: 10/100/1000Base-T Twisted Pair Ports

    Chapter 1: Overview 10/100/1000Base-T Twisted Pair Ports This section describes the twisted pair ports on the AT-9424T/GB, AT-9424T/SP, AT-9448Ts, AT-9448T/SP, and AT-9448Ts/XP switches. Connector Type The ports have 8-pin RJ-45 connectors. The ports use four pins when operating at 10 or 100 Mbps and all eight pins when operating at 1000 Mbps.

  • Page 21: Maximum Distance

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Maximum The ports have a maximum operating distance of 100 meters (328 feet). Distance Cable Type The cabling requirements for a 10/100/1000Base-T port are: For 10 Mbps operation: Standard TIA/EIA 568-B-compliant Category 3 or better shielded or unshielded cabling with 100 ohm impedance and a frequency of 16 MHz.

  • Page 22: Fiber Optic Ports

    Chapter 1: Overview Fiber Optic Ports This section applies to ports 1 through 8 on the AT-9408LC/SP switch. Connector Type The ports feature LC-duplex connectors. Speed The ports have fixed speed of 1000 Mbps (1000Base-SX). Maximum The ports have a maximum distance of 275 meters (m) with 62.5/125 µm (core/cladding) multimode fiber optic cable and 550m with 50/125 µm...

  • Page 23: Gbic Transceiver Slots

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide GBIC Transceiver Slots The AT-9424T/GB switch has two slots on the front panel labeled 23 and 24 for optional fiber optic Gigabit Interface Converter (GBIC) Ethernet transceivers. GBIC modules can be installed to interconnect devices over large distances using fiber optic cable.

  • Page 24: Sfp Transceiver Slots

    Several of the AT-9400 Series switches feature slots for optional Gigabit Ethernet SFP transceivers for interconnecting network devices over large distances using fiber optic cable. With the exception of the AT-9408LC/SP switch, each SFP slot is paired with a twisted pair port. A link on an SFP...

  • Page 25: Xfp Transceiver Slots

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide XFP Transceiver Slots Several AT-9400 Series switches have slots for optional XFP 10 Gigabit Ethernet transceivers to connect high speed, 10 gigabit devices to the switch or create high speed backbone networks between switches. Figure 11 shows an example of an XFP transceiver.

  • Page 26: Redundant Twisted Pair Ports

    Chapter 1: Overview Redundant Twisted Pair Ports Your AT-9400 Series switch may have two or four twisted pair ports that are paired with GBIC or SFP slots. The twisted pair ports are identified with the letter “R” for “Redundant” as part of their number on the front faceplate of the unit.
  • Page 27 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Note These guidelines do not apply to the SFP slots on the AT-9408LC/SP switch and the XFP slots on the AT-9424Ts/XP and AT-9448Ts/XP switches.

  • Page 28: Compact Flash Card Slot

    Chapter 1: Overview Compact Flash Card Slot The compact flash card slot featured on many of the switches in the AT-9400 Series and shown in Figure 12 can be used to store configuration files and AT-S63 management software image files on a compact flash card.

  • Page 29: Port Leds

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Port LEDs The following sections describe the twisted pair and fiber optic port LEDs. 10/100/1000Base- A twisted pair port has two LEDs labeled L/A (link/activity) and D/C (duplex mode/collisions). The L/A LED indicates the speed and activity on a port. T Twisted Pair The D/C LED indicates the duplex mode (full- or half-duplex) and the Port LEDs...

  • Page 30: Fiber Optic Port And Transceiver Slot Leds

    Chapter 1: Overview Fiber Optic Port The 1000Base-SX fiber optic ports on the AT-9408LC/SP switch and the GBIC and SFP transceiver slots have one LED. The LED is defined in and Transceiver Table 4. Slot LEDs Table 4 1000Base-SX Port and GBIC and SFP Slot LED...

  • Page 31: System Leds

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide System LEDs The system LEDs on the front panel display general status information, as described in Table 6. Table 6 System LEDs State Description FAULT or Normal operation. Solid The switch or management software has malfunctioned.

  • Page 32: Expansion Slot And Stack Leds

    Chapter 1: Overview Expansion Slot and STACK LEDs The expansion slot and STACK LEDs featured on some of the AT-9400 Series switches are reserved for future use. Consult your local Allied Telesyn sales representative for information on these features.

  • Page 33: Terminal Port

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Terminal Port The terminal port is used to establish a local (out-of-band) management session with the switch and configure the switch’s operating parameters. You establish a local management session with the switch by connecting a terminal or a personal computer with a terminal emulation program to the port.

  • Page 34: At-Rps3204 Redundant Power Supply

    Chapter 1: Overview AT-RPS3204 Redundant Power Supply The RPS connector on the back panel of the switch connects to the optional AT-RPS3204 redundant power supply unit, shown in Figure 13. The unit can provide power to the switch in the event that the switch’s internal power supply fails.

  • Page 35: Ac Power Connector

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide AC Power Connector The AT-9400 Series switches have a single AC power supply socket on the back panel, which has autoswitch AC inputs. To power the switch on or off, connect or disconnect the power cord. Refer to “Technical Specifications”...
  • Page 36 Chapter 1: Overview...

  • Page 37: Installation

    Chapter 2 Installation This chapter contains the installation procedures for the switch. The chapter contains the following sections: “Reviewing Safety Precautions” on page 38 “Selecting a Site” on page 40 “Planning the Installation” on page 41 “Unpacking the Switch” on page 43 “Installing the Power Cord Retaining Clip (AC Switches Only)”...

  • Page 38: Reviewing Safety Precautions

    Chapter 2: Installation Reviewing Safety Precautions Please review the following safety precautions before you begin to install the switch or any of its components. Refer to Appendix B, “Translated Safety Statements” on page 77 for translated safety statements in your language.
  • Page 39 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

  • Page 40: Selecting A Site

    Chapter 2: Installation Selecting a Site Observe the following requirements when choosing a site for your switch: If you plan to install the switch in an equipment rack, check to be sure the rack is safely secured and will not tip over. Devices in a rack should be installed starting at the bottom, with the heavier devices near the bottom of the rack.

  • Page 41: Planning The Installation

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Planning the Installation Twisted Pair Table 7 lists the cabling specifications for the 10/100/1000Base-T twisted pair ports. Cabling Table 7. Twisted Pair Cabling and Distances Maximum Speed Cable Type Operating Distance 10 Mbps Standard TIA/EIA 568-B-compliant 100 m (328 ft)

  • Page 42: Fiber Optic Cabling

    1000 Mbps. Fiber Optic Table 8 lists the fiber optic cabling specifications for ports 1 to 8 on the AT-9408LC/SP switch. For optical specifications, refer to “AT-9408LC/SP Cabling Switch 1000Base-SX Port Specifications” on page 73.

  • Page 43: Unpacking The Switch

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Unpacking the Switch To unpack the switch, perform the following procedure: 1. Remove all components from the shipping package. Note Store the packaging material in a safe location. You must use the original shipping material if you need to return the unit to Allied Telesyn.

  • Page 44: Installing The Power Cord Retaining Clip (Ac Switches Only)

    Chapter 2: Installation Installing the Power Cord Retaining Clip (AC Switches Only) Perform the following procedure to install the power cord retaining clip on an AC powered AT-9400 Series switch: Note Install the power cord retaining clip before you install the switch in a rack.
  • Page 45 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide 4. Verify that the retaining clip is in the correct position, shown in Figure 17. 1 0 0 - 2 4 0 V A Figure 17. Retaining Clip Properly Installed in the Bracket...

  • Page 46: Installing The Switch In A Rack

    Chapter 2: Installation Installing the Switch in a Rack Perform the following procedure to install the switch in a standard 19-inch rack: 1. Place the unit upside down on a level, secure surface. 2. Using a flat-head screwdriver, remove the snap-on plastic feet from the bottom of the switch, as shown in Figure 18.
  • Page 47 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide 6. Mount the switch in the 19-inch rack using standard screws (not provided), as shown in Figure 20. L /A 9 4 0 8 L C / S P G i g a b i t E t h e r n e t...

  • Page 48: Installing An Optional Transceiver

    Chapter 2: Installation Installing an Optional Transceiver Review the following guidelines before installing an optional GBIC, SFP or XFP transceiver in a switch: A transceiver can be hot-swapped; the switch can be powered on when you install it. However, you should always disconnect the cables first before removing a transceiver.

  • Page 49: Installing An Sfp Transceiver

    “Cabling the Switch” on page 53. For GBIC optical and cabling specifications, consult the documentation shipped with the module. Installing an SFP To install an SFP transceiver in an AT-9408LC/SP, AT-9424T/SP, AT-9424Ts, AT-9424Ts/XP or AT-9448T/SP switch, perform the following Transceiver procedure: 1.
  • Page 50 Chapter 2: Installation 4. Slide the transceiver into the slot until it clicks into place. Figure 23. Installing an SFP Transceiver 5. Check to be sure that the handle on the SFP transceiver is in the upright position, as shown in Figure 24, to prevent inadvertently removing the transceiver.

  • Page 51: Installing An Xfp Transceiver

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Installing an XFP To install an XFP transceiver in an AT-9424Ts/XP or AT-9448Ts/XP switch, perform the following procedure: Transceiver 1. Remove the dust plug from the transceiver slot where the XFP transceiver is to be installed, as shown in Figure 25.
  • Page 52 Chapter 2: Installation For XFP optical and cabling specifications, consult the documentation shipped with the module.

  • Page 53: Cabling The Switch

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Cabling the Switch Observe the following guidelines when connecting a twisted pair or fiber optic cable to a port on the switch: The connector on the cable should fit snugly into the port on the switch.

  • Page 54: Applying Ac Power

    Chapter 2: Installation Applying AC Power To apply AC power to the switch, perform the following procedure: 1. Position the power cord retaining clip in the up position, as shown in Figure 27. 1 0 0 - 2 4 0 V A Figure 27.
  • Page 55 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide 3. Secure the cord by lowering the power cord retaining clip, as shown in Figure 29. 1 0 0 - 2 4 0 V A Figure 29. Securing the Power Cord with the Retaining Clip 4.

  • Page 56: Starting A Local Management Session

    Chapter 2: Installation Starting a Local Management Session The procedure in this section explains how to start a local (out-of-band) management session using the RJ-45 terminal port on the switch. You can use a local management session to configure the switch’s operating parameters and view performance and error statistics.
  • Page 57 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Stop bits: 1 Flow control: None Note The port settings are for a DEC VT100 or ANSI terminal, or an equivalent terminal emulator program. 4. Press Enter. You are prompted for a user name and password. 5.

  • Page 58: Warranty Registration

    Chapter 2: Installation Warranty Registration For warranty information or to register your product, go to the Allied Telesyn web site at www.alliedtelesyn.com.

  • Page 59: Chapter 3 Troubleshooting

    Chapter 3 Troubleshooting This chapter contains information about how to troubleshoot the switch in the event a problem occurs. Note If after following the instructions in this chapter you are unable to resolve the problem, contact Allied Telesyn Technical Support for assistance.

  • Page 60: Power Led Is Off

    Chapter 3: Troubleshooting Power LED is Off Check the PWR LED on the front of the switch. If the LED is off, indicating that the unit is not receiving power, do the following: Make sure the power cord is securely connected to the power source and to the AC connector on the back panel of the switch.

  • Page 61: Twisted Pair Port Link Led Is Off

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Twisted Pair Port Link LED is Off When a twisted pair port on the switch is connected to a properly operating end node, the Link LED for the port should be on. If a Link LED is off, do the following: Verify that the end node connected to the port is powered ON and is operating properly.

  • Page 62: Fiber Optic Port Link Led Is Off

    Use a fiber optic tester to test the attenuation on the cable and the strength of the optical signal. The operating specifications for the ports on the AT-9408LC/SP switch are listed in Table 12 on page 73. For operating specifications for an SFP or GBIC module, refer to the installation instructions shipped with the module.

  • Page 63: Transceiver Is Installed But The Status Is "Not Present

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Transceiver is Installed but the Status is “Not Present” If a GBIC, SFP, or XFP transceiver is installed in a transceiver slot but the Uplink Information menu in the AT-S63 management software interface displays “Not Present”...

  • Page 64: System Fault Led Is Blinking

    Chapter 3: Troubleshooting System Fault LED is Blinking If the system FAULT LED is blinking, no action is required. A blinking FAULT LED could indicate that a new version of the management software is being downloaded to the switch or the switch’s is updating the active boot configuration file.

  • Page 65: System Fault Led Is Steadily On

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide System Fault LED is Steadily On If the system FAULT LED is steadily on, a problem has occurred in the switch. Do the following: Try resetting the switch by disconnecting and reconnecting the AC power cord.

  • Page 66: Cannot Establish A Local (Out-Of-Band) Management Session

    Chapter 3: Troubleshooting Cannot Establish a Local (Out-of-Band) Management Session If you are unable to establish a local (out-of-band) management session with the switch through the terminal port on the front panel, do the following: Check to be sure that the RJ-45 serial management cable is securely connected to the serial terminal port on the switch and to the RS-232 port on the terminal or personal computer.

  • Page 67: Switch Functions Intermittently

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Switch Functions Intermittently If the switch functions intermittently, check the system hardware status through the management interface: Note the current voltage for the power supply compared to the optimum rating. Verify that the system temperature is within the operating range. Review the fan speeds to verify the fans are operating properly.
  • Page 68 Chapter 3: Troubleshooting...

  • Page 69: Technical Specifications

    Appendix A Technical Specifications Physical Specifications Dimensions (H x W x D): AT-9408LC/SP 4.4 cm x 44.0 cm x 22.2 cm AT-9424T/GB (1.75 in. x 17.34 in. x 8.75 in.) AT-9424T/SP AT-9424Ts 4.4 cm x 43.8 cm x 30.4 cm AT-9424Ts/XP (1.75 in.

  • Page 70: Power Specifications

    Appendix A: Technical Specifications Power Specifications Maximum Power Consumption: AT-9408LC/SP 58 watts AT-9424T/GB 54 watts AT-9424T/SP 54 watts AT-9424Ts 54 watts AT-9424Ts/XP 68 watts AT-9448Ts 102 watts AT-9448T/SP 120 watts AT-9448Ts/XP 128 watts Input Voltage: 100-240 VAC, 2.0 A maximum, 50/60 Hz...

  • Page 71: Rj-45 Twisted Pair Port Pinouts

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide RJ-45 Twisted Pair Port Pinouts Figure 32 illustrates the pin layout of an RJ-45 connector and port. Pin 1 Figure 32. RJ-45 Connector and Port Pin Layout Table 9 lists the pin signals when a port is operating in the MDI configuration at 10 or 100 Mbps.
  • Page 72 Appendix A: Technical Specifications Table 11 lists the pin signals when a port operating at 1000 Mbps. Table 11. Pin Signals - 1000 Mbps Pinout Pair Pair 1 + Pair 1 - Pair 2 + Pair 3 + Pair 3 - Pair 2 - Pair 4 + Pair 4 -...

  • Page 73: At-9408Lc/Sp Switch 1000Base-Sx Port Specifications

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide AT-9408LC/SP Switch 1000Base-SX Port Specifications Table 12 lists the operating specifications for ports 1 to 8 on the AT-9408LC/SP switch. Table 12. 1000Base-SX Port Specifications Property Value Transmitter Characteristics Wavelength 850 nm Output Power Min: -9.5 dBm...

  • Page 74: Rj-45 Style Serial Terminal Port Pinouts

    Appendix A: Technical Specifications RJ-45 Style Serial Terminal Port Pinouts Table 13 lists the pin signals on the RJ-45 style serial terminal port. Table 13. RJ-45 Style Serial Terminal Port Pin Signals Signal Data Carrier Detect Transmit Data Receive Data Data Set Ready Ground Data Terminal Ready...
  • Page 75 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Table 14 lists the definitions for the RPS 21-pin D-combo port and connector pins. Table 14. RPS 21-pin D-combo Port and Connector Pin Definitions Definition Reserved Fan 2 status Fan 1 status RPS status Ground Ground...
  • Page 76 Appendix A: Technical Specifications...

  • Page 77: Translated Safety Statements

    Appendix B Translated Safety Statements Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Importante: Este apéndice contiene traducciones en múltiples idiomas de los mensajes de seguridad incluidos en esta guía.

  • Page 78: Laser Safety Notices

    Appendix B: Translated Safety Statements Laser Safety Notices Warning: Class 1 Laser product. Warning: Do not stare into the laser beam. Electrical Safety Notices Warning: To prevent electric shock, do not remove the cover. No user-serviceable parts inside. This unit contains hazardous voltages and should only be opened by a trained and qualified technician.
  • Page 79 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Warning: Check to see if there are any exposed copper strands coming from the installed wire. When this installation is done correctly there should be no exposed copper wire strands extending from the terminal block. Any exposed wiring can conduct harmful levels of electricity to persons touching the wires.
  • Page 80 Appendix B: Translated Safety Statements Warning: Mounting of the equipment in the rack should be such that a hazardous condition is not created due to uneven mechanical loading. Warning: Remove all metal jewelry, such as rings and watches, before installing or removing a line card from a powered-on chassis.

  • Page 81: Telecommunications Compliance Notices

    AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Telecommunications Compliance Notices Warning: When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electronic shock, and injury to persons, including the following: Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub in a wet basement or near a swimming pool.
  • Page 82 Appendix B: Translated Safety Statements Lasersicherheitshinweise Achtung: Laserprodukt der Klasse 1. Achtung: Blicken Sie nicht in den Laserstrahl. Elektrische Sicherheitshinweise Achtung: Um Stromschläge zu vermeiden, darf die Abdeckung nicht entfernt werden. Die Ausrüstung enthält keine benutzerwartbaren Teile. Diese Einheit führt gefährliche Spannungen und sollte nur durch einen ausgebildeten und qualifizierten Techniker geöffnet werden.
  • Page 83 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Achtung: Nicht mehr als die empfohlene Kabellänge abisolieren. Durch das Abisolieren von mehr als der empfohlenen Länge können gefährliche blanke Drähte aus dem Anschlussblock hervorragen. Achtung: Beim Installieren dieser Ausrüstung ist stets darauf zu achten, dass die Rahmenerdung zuerst angeschlossen und zuletzt abgetrennt wird.
  • Page 84 Appendix B: Translated Safety Statements Bei der Versorgung der Einheit durch zentralisierten Gleichstrom ist ein Tray-Kabel zum Anschluss der Stromquelle erforderlich. Das Tray-Kabel muss ein UL-gelistetes Typ-TC-Tray-Kabel mit einer Nennspannung von 600 V und einer Nenntemperatur von 90 Grad Celsius, mit drei Leitern und mindestens 14 AWG sein. Achtung: Bei der Rackmontage der Ausrüstung ist darauf zu achten, dass keine Gefahrenbedingung durch ungleichmäßige mechanische Belastung geschaffen wird.
  • Page 85 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Telekommunikationskonformitätshinweise Achtung: Bei der Verwendung Ihrer Telefonausrüstung sollten zur Reduzierung der Brand-, Stromschlag und Verletzungsgefahr stets grundsätzliche Sicherheitsrichtlinien, einschließlich der folgenden, befolgt werden: Verwenden Sie dieses Produkt nicht in der Nähe von Wasser, zum Beispiel in der Nähe einer Badewanne, einer Waschschüssel, eines Spülbeckens, eines Waschbottichs, in einem nassen Kellerraum oder in der Nähe eines Schwimmbads.
  • Page 86 Appendix B: Translated Safety Statements Avisos de seguridad láser Atención: Producto láser de clase 1. Atención: No mire el rayo láser. Avisos de seguridad eléctricas Atención: Para evitar la electrocución, no quite la tapa. La unidad no contiene piezas que pueda reparar el usuario. Esta unidad contiene tensiones peligrosas y sólo la debe abrir un técnico convenientemente formado y cualificado.
  • Page 87 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Atención: Cuando instale el equipo, asegúrese de instalar primero la conexión a tierra del bastidor y de desconectarla en último lugar. Atención: Compruebe si hay algún hilo de cobre al descubierto que proceda del cable instalado.
  • Page 88 Appendix B: Translated Safety Statements Atención: Si el equipo se monta en un rack, se deberá evitar todo peligro de irregularidad en la carga mecánica. Atención: Quítese todas las joyas metálicas, como anillos y relojes, antes de instalar o quitar una tarjeta de red de un chasis con alimentación eléctrica. Utilice circuitos de alimentación dedicados o acondicionadores de alimentación para suministrar energía eléctrica fiable al dispositivo.
  • Page 89 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Avisos de conformidad de telecomunicaciones Atención: Cuando utilice su equipo telefónico, deberá adoptar las siguientes precauciones de seguridad básicas para reducir el riesgo de incendio, descarga electrónica y lesiones: No utilice este producto en zonas húmedas; por ejemplo, cerca de una bañera, un lavabo o un fregadero, en un sótano húmedo o cerca de una piscina.
  • Page 90 Appendix B: Translated Safety Statements Avis de sécurité laser Avertissement: Produit laser de classe 1. Avertissement: Ne pas observer directement le rayon laser. Avis de sécurité électrique Avertissement: Pour éviter tout risque d’électrocution, ne pas déposer le capot. L’appareil ne contient aucun composant réparable par l’utilisateur. Il est exposé à des tensions dangereuses et ne doit être ouvert que par un technicien compétent et qualifié.
  • Page 91 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Avertissement: Respecter les recommandations pour dénuder les fils. Un dénudage excessif risque de présenter des risques pour la sécurité en laissant le fil exposé sur le bornier après l’installation. Avertissement: Lors de l’installation de cet équipement, toujours s’assurer que la connexion de terre de la structure est installée en premier et déconnectée en dernier.
  • Page 92 Appendix B: Translated Safety Statements Un chemin de câble doit être utilisé pour la connexion à la source d’alimentation si l’unité est alimentée par alimentation c.c. centralisée. Le chemin de câble doit être de type TC agréé UL, intensité nominale de 600 V, 90 °C, trois conducteurs, 14 AWG minimum.
  • Page 93 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Télécommunications – Avis de conformité Avertissement: Les précautions élémentaires de sécurité doivent être systématiquement respectées en utilisant l’équipement téléphonique pour réduire les risques d’incendie, d’électrocution et d’accident corporel, notamment: Ne pas utiliser ce produit près d’une source d’eau, telle qu’une baignoire, un lavabo, un évier ou un baquet dans un sous-sol humide ou près d’une piscine.
  • Page 94 Appendix B: Translated Safety Statements Indicazioni sulla sicurezza laser Avvertenza: Prodotto laser Classe 1. Avvertenza: Non fissare il raggio laser. Indicazioni sulla sicurezza elettrica Avvertenza: Per evitare scosse elettriche, non rimuovere la copertura. All'interno non sono presenti componenti utilizzabili dall'utente. Questa unità presenta voltaggi rischiosi e deve essere aperta solo da un tecnico qualificato ed esperto.
  • Page 95 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Avvertenza: Quando si installa l'apparecchiatura, verificare che il collegamento di messa a terra FG (frame ground) sia installato per primo e disinstallato per ultimo. Avvertenza: Verificare che non sporgano fili di rame dai cavi installati. Se l'installazione viene effettuata correttamente, non vi sono fili di rame scoperti, sporgenti dal blocco terminale.
  • Page 96 Appendix B: Translated Safety Statements Avvertenza: Rimuovere tutti gli oggetti di metallo, ad esempio anelli e orologi, prima di installare o estrarre una scheda di linea da un chassis acceso. Utilizzare circuiti di alimentazione o alimentatori dedicati per fornire energia elettrica al dispositivo in modo affidabile.
  • Page 97 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Indicazioni per la conformità con le norme sulle telecomunicazioni Avvertenza: Quando si utilizza l'apparecchiatura telefonica, per ridurre il rischio di incendio, scosse elettriche e danni alle persone, è necessario seguire alcune precauzioni di base per la sicurezza, ad esempio: Non utilizzare il prodotto in prossimità...
  • Page 98 Appendix B: Translated Safety Statements Лазерная безопасность Внимание: лазерный продукт, класс 1. Внимание: Не смотрите прямо в лазерный луч. Электрическая безопасность Внимание: Для предотвращения электрического шока, не снимайте кожух. Внутри нет частей, подлежащих обслуживанию пользователем. Этот устройство – под опасным напряжением и должно открываться только обученным и квалифицированным...
  • Page 99 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Внимание: При инсталляции оборудования, убедитесь, что заземление подключается в первую, а отключается в последнюю очередь. Внимание: Проверьте, нет ли на инсталлированных проводков на кабеле. При правильной инсталляции на терминале свободных проводков быть не должно. Открытые...
  • Page 100 Appendix B: Translated Safety Statements Для подсоединения источника питания, если установка питается централизованным постоянным током, требуется желобной кабель. Кабель должен быть признанным UL типа и предназначен для 600 В и + 90°C, с тремя кондукторами, минимум 14 AWG (американский калибр). Внимание: Установка...
  • Page 101 AT-9400 Series Layer 2+ Gigabit Ethernet Switches Installation Guide Телекоммуникационное соответствие Внимание: При использовании телефонного оборудования, всегда следует обращать внимания на требования безопасности для снижения риска пожара, поражения током и ранения, в том числе: Не используйте оборудование рядом с водой – например ванной, раковиной или стиральным...
  • Page 102 Appendix B: Translated Safety Statements...

This manual is also suitable for:

At-9424t/spAt-9424t/gbAt-9448tsAt-9448t/spAt-9448ts/xpAt-9424ts ... Show all

Table of Contents