Related Manuals for Supero SC733i-665B
Summary of Contents for Supero SC733i-665B
- Page 1 UPER ® SC733 CHASSIS SERIES Reset Reset SC733i-665B SC733TQ-665B SC733TQ-500B SC733T-500B SC733i-500B SC733E-500B SC733TQ-465B SC733T-465B SC733i-465(B) SC733E-465B USER’S MANUAL...
- Page 2 This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.
-
Page 3: About This Manual
SC733 chassis. Installation and maintenance should be performed by experienced technicians only. Supermicro’s SC733 chassis features a unique and highly-optimized design for Intel and AMD platforms. The chassis is equipped with a 465W, 500W, or 665W high-efficiency power supply for superb power savings. -
Page 4: Manual Organization
SC733 Chassis Manual Manual Organization Chapter 1: Introduction The first chapter provides a checklist of the main components included with this chassis and describes the main features of the SC733 chassis. This chapter also includes contact information. Chapter 2: Standardized Warning Statements for AC/DC Systems This chapter lists warnings, precautions, and system safety. -
Page 5: Table Of Contents
Chapter 1 Introduction Overview ......................1-1 Shipping List ....................1-1 Where to get Replacement Components ............1-2 Contacting Supermicro ..................1-3 Returning Merchandise for Service..............1-4 Chapter 2 Standardized Warning Statements for DC Systems About Standardized Warning Statements ............2-1 Warning Definition ................... - Page 6 SC733 Chassis Manual Installing the Motherboard, I/O Shield and Standoffs ........4-9 I/O Shield ......................4-9 Permanent and Optional Standoffs ............... 4-10 Motherboard Installation .................4-11 Installing Expansion Cards ................4-12 PCI Slot Setup ....................4-12 Removing the Fan Duct and System Fan ............ 4-13 Checking the Server's Airflow ...............
-
Page 7: Chapter 1 Introduction
The ultra-quiet thermal fans ensure a noise-free operating environment. Shipping List Please visit the Supermicro web site for the latest shiping lists and part numbers for your particular chassis model at www.supermicro.com. SC733 Chassis... -
Page 8: Where To Get Replacement Components
Supermicro Authorized Distributors/ System Integrators/Resellers. A list of Supermicro Authorized Distributors/System Integrators/Reseller can be found at: http://www.supermicro.com. Click the Where to Buy link. -
Page 9: Contacting Supermicro
Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML... -
Page 10: Returning Merchandise For Service
For faster service, RMA authorizations may be requested online (http://www. supermicro.com/support/rma/). Whenever possible, repack the chassis in the original Supermicro carton, using the original packaging material. If these are no longer available, be sure to pack the chassis securely, using packaging material to surround the chassis so that it does not shift within the carton and become damaged during shipping. -
Page 11: Chapter 2 Standardized Warning Statements For Dc Systems
Only certified technicians should attempt to install or configure components. Read this appendix in its entirety before installing or configuring components in the Supermicro chassis. These warnings may also be found on our web site at http://www.supermicro.com/ about/policies/safety_information.cfm. Warning Definition Warning! This warning symbol means danger. - Page 12 SC733 Chassis Manual Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut.
- Page 13 Chapter 2: Warning Statements for AC/DC Systems جسذٌة اصابة ًتتسبب ف حالة ٌوكي أى ًاًك ف خطز ًٌٌع هذا الزهز !تحذٌز الذوائز بالوخاطز الٌاجوة عي ي على علن ، ك هعذات تعول على أي قبل أى الكهزبائٍة حىادث أي وقىع وٌع...
-
Page 14: Installation Instructions
SC733 Chassis Manual Installation Instructions Warning! Read the installation instructions before connecting the system to the power source. 設置手順書 システムを電源に接続する前に、 設置手順書をお読み下さい。 警告 将此系统连接电源前,请先阅读安装说明。 警告 將系統與電源連接前，請先閱讀安裝說明。 Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación. -
Page 15: Circuit Breaker
Chapter 2: Warning Statements for AC/DC Systems Circuit Breaker Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 20 A. サーキッ ト ・ ブレーカー この製品は、 短絡 （過電流） 保護装置がある建物での設置を前提としています。 保護装置の定格が60V、... -
Page 16: Power Disconnection Warning
SC733 Chassis Manual 경고! 이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 60V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다. Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 60V, 20A. - Page 17 Chapter 2: Warning Statements for AC/DC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché...
-
Page 18: Equipment Installation
SC733 Chassis Manual Equipment Installation Warning! Only trained and qualified personnel should be allowed to install, replace, or service this equipment. 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、 交換、 またはサービスを許可 されています。 警告 只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。 警告 只有經過受訓且具資格人員才可安裝、更換與維修此設備。 Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden. -
Page 19: Restricted Area
Chapter 2: Warning Statements for AC/DC Systems Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door geschoold en gekwalificeerd personeel. Restricted Area Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. -
Page 20: Battery Handling
SC733 Chassis Manual אזור עם גישה מוגבלת !אזהרה יש להתקין את היחידה באזורים שיש בהם הגבלת גישה. הגישה ניתנת בעזרת .)'כלי אבטחה בלבד (מפתח, מנעול וכד محظورة مناطق ٍنتركُبها ف هذه انىحذة تخصيص تم ،أداة خاصت من خالل استخذاو فقط محظورة... - Page 21 Chapter 2: Warning Statements for AC/DC Systems Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant.
-
Page 22: Redundant Power Supplies
SC733 Chassis Manual Redundant Power Supplies Warning! This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. 冗長電源装置 このユニッ トは複数の電源装置が接続されている場合があります。 ユニッ トの電源を切るためには、 すべての接続を取り外さなければなりません。 警告 此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。 警告 此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。 Warnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden. -
Page 23: Backplane Voltage
Chapter 2: Warning Statements for AC/DC Systems امداد الطاقة بوحدات عدة اتصاالت جهاز ال يكون لهذا قد الكهرباء عن وحدة ال لعسل كافة االتصاالت يجب إزالة 경고! 이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을... -
Page 24: Comply With Local And National Electrical Codes
SC733 Chassis Manual מתח בפנל האחורי !הרה אז קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת. יש להיזהר במהלך .העבודה اللىحة أوالطاقة المىجىدة على التيار الكهزبائي مه خطز هناك هذا الجهاس خدمة كه حذرا عند يعمل النظام عندما يكىن 경고! 시스템이... -
Page 25: Product Disposal
Chapter 2: Warning Statements for AC/DC Systems Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. תיאום חוקי החשמל הארצי !אזהרה הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים התקנת المتعلقة المحلية والىطىية قىاويه يجب أن يمتثل لل الكهربائية... -
Page 26: Hot Swap Fan Warning
SC733 Chassis Manual ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent. - Page 27 Chapter 2: Warning Statements for AC/DC Systems 警告 當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Warnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador del chasis.
-
Page 28: Dc Power Supply
SC733 Chassis Manual DC Power Supply Warning! When stranded wiring is required, use approved wiring terminations, such as closedloop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor. 警告... - Page 29 Chapter 2: Warning Statements for AC/DC Systems Attention Quand des fils torsadés sont nécessaires, utiliser des douilles terminales homologuées telles que celles à circuit fermé ou du type à plage ouverte avec cosses rebroussées. Ces douilles terminales doivent être de la taille qui convient aux fils et doivent être refermées sur la gaine isolante et sur le conducteur.
-
Page 30: Dc Power Disconnection
SC733 Chassis Manual DC Power Disconnection Warning! Before performing any of the following procedures, ensure that power is removed from the DC circuit. 警告 次の手順を開始する前に、 DC回路から電源が切断されているこ とを確認してく ださい。 警告 進行以下任一操作程序前，請確保直流電路已斷電。 警告 请在进行以下任一操作程序前，确保直流电路的电源已经断开。 Warnung Vor Ausführung der folgenden Vorgänge ist sicherzustellen, daß die Gleichstromschaltung keinen Strom erhält. -
Page 31: Hazardous Voltage Or Energy Present On Dc Power Terminals
Chapter 2: Warning Statements for AC/DC Systems 주의! 다음 절차들을 수행하기 전에, 전원이 DC회로로부터 제거되었는지를 확인해 주십시오. Waarshuwing Wanneer geslagen bedrading vereist is, dient u bedrading te gebruiken die voorzien is van goedgekeurde aansluitingspunten, zoals het gesloten-lus type of het grijperschop type waarbij de aansluitpunten omhoog wijzen. - Page 32 SC733 Chassis Manual ¡Advertencia! Puede haber energía o voltaje peligrosos en los terminales eléctricos de CC. Reemplace siempre la cubierta cuando no estén utilizándose los terminales. Asegúrese de que no haya acceso a conductores descubiertos cuando la cubierta esté colocada. Attention Le voltage ou l'énergie électrique des terminaux à...
-
Page 33: Chapter 3 System Interface
Chapter 3: System Interface Chapter 3 System Interface Overview There are several LEDs on the control panel as well as others on the drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of specific components. -
Page 34: Control Panel Buttons
SC733 Chassis Manual Control Panel Buttons There are two push-buttons located on the front of the chassis. These are a reset button and a power on/off button. Reset: The reset button is used to reboot the system. Power: The main power switch is used to apply or remove power from the power supply to the server system. - Page 35 Chapter 3: System Interface HDD: Indicates IDE channel activity. SAS/SATA drive and/or DVD-ROM drive activ- ity when flashing. NIC1: Indicates network activity on GLAN1 when flashing. Informational LED Informational LED Status Description An overheat condition has occured. Solid red (This may be caused by cable congestion). Fan failure, check for an inoperative fan.
- Page 36 SC733 Chassis Manual Notes...
-
Page 37: Chapter 4 Chassis Setup And Maintenance
Chapter 4: Chassis Setup and Maintenance Chapter 4 Chassis Setup and Maintenance Overview This chapter covers the steps required to install components and perform mainte- nance on the chassis. The only tool you will need to install components and perform maintenance is a Phillips screwdriver. -
Page 38: Removing The Chassis Cover
SC733 Chassis Manual Removing the Chassis Cover Remove Screws Figure 4-1: Removing the Chassis Cover Removing the Chassis Cover: 1. Power down the system and remove the power cord from the rear of the power supply. 2. On the rear of the chassis, remove the two screws holding the cover in place. 3. -
Page 39: Installing Hard Drives In The Sc733I Model Chassis
Chapter 4: Chassis Setup and Maintenance Installing Hard Drives in the SC733i Model Chassis Remove Screws Figure 4-2: Removing the Hard Drive Module The SC733i chassis must be powered-down before hard drives can be removed from the hard drive carriers. Replacing Hard Drives in the SC733i Chassis 1. - Page 40 SC733 Chassis Manual Remove Screws Remove Screws Figure 4-3: Removing Drives from the SC733i Hard Drive Module 4. Remove the four screws securing each of the hard drives. 5. Slide the drive (or dummy drive) out of the hard drive module. 6.
-
Page 41: Installing Hard Drives In The Sc733T And Sc733Tq
3. Using the drive carrier handle, gently pull the drive carrier out of the chassis. Warning! Enterprise level hard disk drives are recommended for use in Supermicro chassis and servers. For information on recommended HDDs, visit the Supermicro... - Page 42 SC733 Chassis Manual Drive Carrier Dummy Drive Figure 4-5: Chassis Drive Carrier The drives are mounted in drive trays to simplify their installation and removal from the chassis. These trays also help promote proper airflow for the drive bays. Warning: Except for short periods of time (swapping hard drives), do not operate the server with the chassis drive bays empty.
- Page 43 Chapter 4: Chassis Setup and Maintenance SAS/SATA Hard Drive Drive Carrier Figure 4-7: Removing Hard Drive 2. Slide the hard drive into the carrier with the printed circuit board side facing down. 3. Carefully align the mounting holes in both the drive carrier and the hard drive. 4.
-
Page 44: Installing A Peripheral Drive
SC733 Chassis Manual Installing a Peripheral Drive SC733 chassis models have peripheral drive bays, in which an optional drive may be installed. This may be a DVD-ROM, DVD-RW or other device. In the unlikely event that it becomes necessary to replace a peripheral drive, use the following procedure. Adding or Replacing a Peripheral Drive 1. -
Page 45: Installing The Motherboard, I/O Shield And Standoffs
Chapter 4: Chassis Setup and Maintenance Installing the Motherboard, I/O Shield and Standoffs I/O Shield Figure 4-10: I/O Shield Placement I/O Shield An I/O shield holds the motherboard ports in place. Install the I/O shield before you install the motherboard. Motherboards are sold separately from SC733 chassis. I/O shields are specific to the motherboard and are included with the motherboard. -
Page 46: Permanent And Optional Standoffs
SC733 Chassis Manual Permanent and Optional Standoffs Standoffs prevent short circuits by securing space between the motherboard and the chassis surface. The SC733 chassis includes permanent standoffs in locations used by most motherboards. These standoffs accept the rounded Phillips head screws included in the SC733 accessories packaging. -
Page 47: Motherboard Installation
Chapter 4: Chassis Setup and Maintenance Motherboard Installation Installing the Motherboard: 1. Review the documentation that came with your motherboard. Become familiar with component placement, requirements, precautions, and cable connec- tions. 2. Power down the system, remove the power cord from the rear of the power supply and open the chassis cover as described in section 4-2. -
Page 48: Installing Expansion Cards
SC733 Chassis Manual Installing Expansion Cards PCI Slots Remove Screws Figure 4-12: Installing Expansion Cards PCI Slot Setup SC733 chassis includes seven PCI slots for expansion cards. Installing Expansion Cards 1. Disconnect the power supply, set the chassis on a flat surface, and open the chassis cover. -
Page 49: Removing The Fan Duct And System Fan
Chapter 4: Chassis Setup and Maintenance Removing the Fan Duct and System Fan Release Tabs Release Tabs Release Tabs Screw Figure 4-13: Replacing the Fan shroud The fan duct concentrates airflow to maximize fan efficiency. Removing the Fan Duct and System Fan 1. -
Page 50: Checking The Server's Airflow
SC733 Chassis Manual Checking the Server's Airflow Checking the Server's Air flow 1. Make sure there are no objects to obstruct airflow in and out of the server. 2. Do not operate the server without drives or drive trays in the drive bays. Use only recommended server parts. -
Page 51: 4-10 Power Supply
Chapter 4: Chassis Setup and Maintenance 4-10 Power Supply Depending on your chassis model the SC733 Chassis has a 465, 500 or 665 Watt power supply. This power supply is auto-switching capable. This enables it to au- tomatically sense and operate at a 100v to 240v input voltage. An amber light will be illuminated on the power supply when the power is off. - Page 52 SC733 Chassis Manual Power Supply Figure 4-14: Removing the Power Supply Changing the Power Supply 1. Disconnect the chassis from any power source. 2. Remove the screws securing the power supply to the chassis, which are located on the rear of the chassis. 3.
-
Page 53: Appendix A Cables, Screws, And Other Accessories
This appendix lists supported cables for your chassis system. It only includes the most commonly used components and configurations. For more compatible cables, refer to the manufacturer of the motherboard you are using and our Web site at: www.supermicro.com. A-2 Cables Included with SC733 Chassis SC733TQ-665(B) - Page 54 SC733 Chassis Manual A-3 Compatible Cables These cables are compatible with the SC733 Chassis. Alternate SAS/SATA Cables Some compatible motherboards have different connectors. If your motherboard has only one SAS connector that the SAS/SATA cables must share, use one of the following cables.
- Page 55 Appendix A: Chassis Cables Extending Power Cables Although Supermicro chassis are designed with to be efficient and cost-effective, some compatible motherboards have power connectors located in different areas. To use these motherboards you may have to extend the power cables to the mother boards.
- Page 56 SC733 Chassis Manual A-4 Chassis Screws The accessory box includes all the screws needed to set up your chassis. This section lists and describes the most common screws used. Your chassis may not require all the parts listed. HARD DRIVE Flat head Pan head 6-32 x 5 mm...
-
Page 57: Appendix B Sc733 Power Supply Specifications
Appendix B: Power Supply Specifications Appendix B SC733 Power Supply Specifications This appendix lists power supply specifications for your chassis system. SC733 665W 500W 465W PWS-665- PWS-502- PWS-465- Part # 100 - 100 - 100 - 240V Rated AC 240V, 50 - 240V, 50 - 60Hz Voltage... - Page 58 SC733 Chassis Manual Notes...
-
Page 59: Appendix C Sas-733Tq Backplane Specifications
SAS-733TQ Backplane Specifications Appendix C SAS-733TQ Backplane Specifications Safety Information and Technical Specifications C-1 Safety Guidelines To avoid personal injury and property damage, please carefully follow all the safety steps listed below when accessing your system or handling the components: ESD Safety Guidelines Electrostatic Discharge (ESD) can damage electronic com ponents. - Page 60 This manual reflects SAS-733TQ Revision 3.00, the most current release available at the time of publication. Always refer to the Supermicro Web site at www.supermi- cro.com for the latest updates, compatible parts and supported configurations.
- Page 61 SAS-733TQ Backplane Specifications 5. Supporting SES-2 (SCSI Enclosure Services-2) protocol, providing the following features: • Drive activity and drive failure indication for each drive slot • Overheat/drive failure alarm via a buzzer* installed on the backplane • An overheat/drive failure LED Indicator built in •...
-
Page 62: Front Connectors
SC733 Chassis Manual C-4 Jumper Settings and Pin Definitions COM PONENT SI DE LAYER 1 Front Jumper/Connector Locations TOP SI LK SCREEN JP13 JP10 OH/DRI VE FAI L JP33: CTRL_I D R221 FAN FAI L R269 1- 2: SGPI O R210 2- 3: I 2C R149... - Page 63 SAS-733TQ Backplane Specifications C-5 Front Connector Pin Definitions Backplane Main Power Connectors (JP10, JP13) Pin Definitions Backplane Main Power 1. Sideband Header - JP51 4-Pin Connectors (JP10, JP13) You must use the 4-pin power con- Pin # Definition nectors JP10 and JP13 to provide adequate power to the backplane.
- Page 64 SC733 Chassis Manual 5. Front Panel Jumper Settings and Pin Definitions Front LED State Specification Overheat, drive failure or fan failure Fan failure only 6. Fan Enable/Disable Jumper Description Definition JP18 Open (Default) Normal Closed Buzzer reset JP26 Open (Default) Act #0 - 3 In JP29 Open (Default)
-
Page 65: Rear Connectors
SAS-733TQ Backplane Specifications C-6 Rear Connectors and LED Indicators Rear connector and LED locations SAS#3 SAS#2 SAS#1 SAS#0 Figure C-2 - Rear View Rear Connectors Rear Connector Specification J1 (Rear) SAS#0 HDD (Connected to HDD) J2 (Rear) SAS#1 HDD (Connected to HDD) J3 (Rear) SAS#2 HDD (Connected to HDD) J4 (Rear) - Page 66 SC733 Chassis Manual Rear Connectors and LED Indicators Rear LED Indicators Specification D12 (Rear) SAS#0 Activity LED D13 (Rear) SAS#1 Activity LED D14 (Rear) SAS#2 Activity LED D15 (Rear) SAS#3 Activity LED D5 (Rear) SAS#0 Fail LED D6 (Rear) SAS#1 Fail LED D7 (Rear) SAS#2 Fail LED D8 (Rear)
-
Page 67: Appendix D Sata-733 Backplane Specifications
This manual reflects SATA-733 Revision 3.00, the most current release available at the time of publication. Always refer to the Supermicro Web site at www.supermicro. com for the latest updates, compatible parts and supported configurations. - Page 68 SC733 Chassis Manual Figure D-1: SATA-733 Backplane Jumper Description Setting JP18 Buzzer Reset* Alarm Reset Header JP25 Overheat Temperature Open: 45ºC Pins 1-2: 50º C (Default) Pins 2-3: 55º C JP26 SATA Drive Activity Drive Activity JP28 Fan Sense Pins 1-2: Enable Pins 2-3: Diable (Default) *The buzzer sound indicates that a condition requiring immediate attention has occurred.
- Page 69 Appendix D: SATA-733 Backplane Specifications Notes...
- Page 70 SC733 Chassis Manual Disclaimer (cont.) The products sold by Supermicro are not intended for and will not be used in life sup- port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to per- form be reasonably expected to result in significant injury or loss of life or catastrophic property damage.