Dimensions And Clearances; Product And Cutout Dimensions; Non Combustible Material - Fisher & Paykel GC36 Installation Information

PRODUCT AND CUTOUT DIMENSIONS

A
B
C
F
D
GC36
A
36" (914mm)
B
21" (533mm)
C 5 /
1 " (41.5mm)
8
D 1 3
/
19 " (494mm) /
[18 " - 19
2 8
E
1 / 3
/
34 " (870mm)
[33 " - 34
4 8
F 3 /
R " (10mm)
8
G
3 /
1 " (30mm)
16
H
1" (25mm)
CLAMPING DOWN THE COOKTOP
Place the cooktop into the cutout
and tighten it with the supplied
clamps. These will cope with the
3 /
countertop thicknesses "- 2"
4
when used in the two orientations
shown.
Do not over tighten.
G
H
E
GC901/GC901M
36" (914mm)
1 /
21 " (546mm)
2
9 /
2 " (65mm) GC901,
16
3" (76mm) GC901M
3 1 1
/
/ 19 " (494mm) /
"] [19 " - 20
4 2 8
3 1 / 7
/ /
34 " (870mm)
"] [33 " - 35
4 4 8
3 /
R " (10mm)
8
3 /
" (20mm)
4
1" (25mm)
3 /
" -
4

DIMENSIONS AND CLEARANCES

CLEARANCES
b
e
a
36" = Minimum horizontal distance between overhead
cabinets installed on either side of this appliance.
5
/
"]
b
30" = Minimum clearance from combustible surface centered
8
1
/
"] above the cooktop.
4
c
13" = Maximum overall depth of overhead cabinetry.
d
18" = Minimum clearance from countertop to overhead cabinetry.
e 1
/
4" (GC36) or 1
from cooktop to the left side wall.
f
1" = Minimum clearance from cooktop to the right side wall.
g
1 /
1 " (GC36) or 1
2
from cooktop to the rear wall.
h 1 /
2 " (GC36) or 1
2
from front edge of counter to front edge of appliance.
Where this reduces the distance between the back edge of the
appliance and the adjacent wall to less than the minimum of
1 /
1 " (GC36) or 1
2
non combustible material (see note below).
i 3 /
2 " (GC36) or 3
8
below countertop to any combustible surface.
2"
j
30" = Maximum distance to nearest grounded power outlet
from the center of the cooktop.
The power cord must not touch any hot metal sufaces.

NON COMBUSTIBLE MATERIAL

Recommended non combustible materials are:
retardant millboard covered with not less than No. 28 MSG sheet
steel, 0.015" (0.4mm) stainless steel, 0.024" (0.6mm) aluminium
or 0.020" (0.5mm) copper.
a
c
d
g
i
h
j
" (GC901 & GC901M) = Minimum clearance
2
1 /
" (GC901 & GC901M) = Minimum clearance
4
1 /
" (GC901 & GC901M) = Minimum distance
4
1 /
" (GC901 & GC901M), this wall must be of
4
5 /
" (GC901 & GC901M) = Minimum clearance
16
1
/
" (6mm) flame
4
US
f
3