SPECIFICATIONS Product Dimensions GC600 Series GC900 Series GC9002/GC36 Series Model Explanation Bench Cut-Out Dimensions GC600 Series GC900 Series GC9002/GC36 Series Clearances (USA Only) § § § § § §...
Page 5
Burners GC600 Series & GC900 / GC9002 / GC36 t f e & t f e Note:...
WIRING DIAGRAM Schematic Wiring Diagram for GC600, GC900 & GC9002 Series Gas Cooktops Ignition Circuit GC900 SERIES ONLY (5 BURNERS) IGNITION SWITCHES IGNITION DANGER - 240V ELECTRODES DISCONNECT 220/240V 0.6VA POWER BEFORE 0.5VA SERVICING UNIT Schematic Wiring Diagram for GC36 Gas Cooktops Ignition Circuit (USA & Canada Only)
REPLACEMENT OF BURNER ORIFICE & LOW SETTING Minimum Setting or Turn Down Note: This is not possible in the UK and Ireland as the gascocks have been sealed. 3.1.1 3.1.2 3.1.3 3.1.4 This picture may not exactly represent all cooktops.
Page 9
Conversion to Different Gas Type Note: For the UK/Ireland, the products must not be converted between gases. The gas taps have been sealed. 3.2.1 3.2.2 3.2.3 3.2.4 3.2.5 Note: 3.2.6 To Change the Gas Pressure (4"NG, 11"LP): (USA/Canada Only)
Page 10
REMOVAL OF HOB TOP How to Remove Hob Top 4.1.1 4.1.2 4.1.3 4.1.4 4.1.5 4.1.6 4.1.7...
REPLACEMENT & SERVICING OF ELECTRONIC IGNITION To Replace an Electrode 6.1.1 6.1.2 6.1.3 6.1.4 To Replace Ignition Box 6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 6.2.6 To Replace the Microswitch Loom (GC600, GC600W and GC36 Only) 6.3.1 6.3.2 6.3.3 6.3.4...
Page 13
REPLACEMENT & SERVICING OF FLAME FAILURE (Refer also Section 9 - Problem Solving) To Test Flame Failure 7.1.1 7.1.2 7.1.3 7.1.4 To Replace a Thermocouple 7.2.1 7.2.2 7.2.3...
GAS VALVES To Change a Gas Valve 8.1.1 8.1.2 8.1.3 8.1.4 8.1.5 8.1.6 8.1.7 8.1.8 8.1.9 Note: 8.1.10 8.1.11 To Re-Grease Gas Valves 8.2.1 8.2.2 8.2.3 8.2.4 8.2.5 8.2.6 8.2.7 8.2.8...
Page 15
PROBLEM SOLVING (excluding Auto Reignition) Gas Doesn't Light - No Spark (See also Section 6) 9.1.1 9.1.2 9.1.3 9.1.4 9.1.5 Gas Doesn't Light - Spark but no Ignition 9.2.1 9.2.2 9.2.3 9.2.4 9.2.5 Flame Doesn't Stay When Gas Valve is Released (See also Section 7) 9.3.1 9.3.2...
Page 17
10.0 PROBLEM SOLVING AUTO REIGNITION 10.1 Gas Doesn't Light - No Spark 10.2 Gas Doesn't Light - Spark but no Ignition 10.3 Sparking Continuously after Ignition 10.3.1 Determine the Problem Burners...
Page 18
10.4 Flame Goes Out on Low Setting 10.5 Flame is Distorted or Large and Yellow...