Fisher & Paykel GC36 Installation Instructions Manual
Hide thumbs
Also See for GC36:
- User manual (52 pages) ,
- Installation instructions manual (33 pages) ,
- Installation information (21 pages)
Related Manuals for Fisher & Paykel GC36
Summary of Contents for Fisher & Paykel GC36
- Page 1 Installation Instructions Installation Irlformation Informaci6n sobre la instalaci6n Informations sur ]'installation GC36 GC912 GC912M 599203B 11,2004 US...
- Page 2 Safety & warnings Flexible appliance connectors shall meet the requirements of ANSI Z21.24 and State Boards. They shall not Electrical Shock Hazard exceed 36 inches in length. Disconnect power before servicing the CAUTION! product. In order to avoid hazard these products Failure to do so could must be installed according to these result in death or...
- Page 3 Before you start Parts checklist Cabinet Preparation Ensure the countertop is square and level Gas Cooktop base unit and ensure no structural members interfere Literature pack (includes LPG kit) with space requirements. Elbow & blue washer (taped to power cord) Make sure the countertop is made of a heat resistant material.
- Page 4 Product GC36 GC912/GC912M A Width 36"(914 ram) 36"(914 ram) 13 Depth 21"(533 turn) 211/2"(546 ram) C Height ] S/s"(41.5 rnrn) 2g/16"(65 ram) GC912 3"(76 ram) GC9]2M Cutout GC36 GC912/GC912M D Width 34_A"(870 ram) [3P/s" 34sA'1 34_A"(870 ram) [33// 3_i/,,/] I;: Depth...
- Page 5 13"= Maximum overall depth of overhead cabinetry. 18"= Minimum clearance from countertop to overhead cabinetry. 4"(GC36) or 11/2"(GC912 & GC912M) = Minimum clearance from cooktop to the left side wall. 1"= Minimum clearance from cooktop to the right side wall.
-
Page 6: Installation
Installation Instructions Gas supply connection Gas corsrsectiorsto the product must use This appliance is factory set for use with the elbow supplied with a 72" NPT external Natural Gas at 4"of water column pressure. thread. It carl also be used ors LP Gas at 11"of water column pressure after conversion (see pages Ensure the blue washer (supplied) is 7&8). - Page 7 Instamlation Instructions Converting the regulator between NG & LP Unscrew the cap from the regulator. Replace regulator cap. Check the orientation of the plastic Test gas pressure (test point provision on conversion plug, and if necessary, unscrew, side of regulator). When converting the turn over and screw back in (wide section regulator for different settings, the function away from cap for LPand against cap for...
-
Page 8: Conversion To Different Gas Type
Installation Instructions Conversion to different gas type 12 The label supplied with the orifices should be placed over the existing gas type label Burners can be used with NG or LPG, to indicate the change. provided that the injector orifices appropriate for the gas delivered are installed. - Page 9 Installation Instructions Leak testing Minimum setting or turndown Leaktesting of the appliance shall be This has beer] preset at the factory for NG but carl be checked after the correct conducted according to the manufacturer's instructions. pressure has beer] reached. To adjust for rninirT]urT]setting (if applicable), you The appliance and it's individual shutoff will need a O 7/64"x lSA"(Q2.5 x 45mm)
- Page 10 Installation Instructions Checking the gas type GC36 Bu_ae_s NG OHfke LP Odfke (ram) BTU(MJ/h) @ (ram) BTU (MJ/h) @ 0.15psi (4"H20) 0.41psi (1 l"H20) RH Rear 1.3 mm 8,000 (8.4 MJ/h) 0.8 mm 8,000 (8.4 MJ/h) LH Rear 1.3 mm 8,000 (8.4 MJ/h)
-
Page 11: Troubleshooting
Trouble shooting Slow to Ignite Doesn't Doesn't Doesn't or Yellow Ignite? Stop stay lit? flames? Sparking? Trouble shooting Burners correctly assembled? Dirty Electrodes? Gas pressure correct? Low Setting correct? Jets incorrect or blocked? Power supply polarity / earth ok? Supply voltage Draft / extraction? (Cust. - Page 12 Advertencias e infor aci6n sobre seguridad Los conectores flexibles del aparato deben cumplir con los requisitos del ANSI Z21.24 y de los Consejos Estatales. No pueden exceder las 36 Peligro de Electrocuci6n pulgadas de largo. Desconecte la corriente el_ctrica antes de reparar el iCUIDADO! producto.
- Page 13 Antes de empezar Preparaci6n de la mesa donde Lista de verificaci6n de piezas Unidad de base de la parrilla a gas ir_ colocada la parrilla ° Aseg0rese de que la superfide est6 en Paquete con information (incluye juego gas a'ngulo recto y nivelada y aseg0rese de que ninguna parte estructural interfiera con los Codo y arandela azul (asegurados al cable requerimientos de espacio.
- Page 14 Dimensiones y distandas de separad6n Producto GC36 GC9121GC912M A Ancho 36"(914 ram) 36"(914 ram) B Profundidad 21" (533 m m) 21 _/2"(546 ram) C Altura I s/s"(41.5 ram) 29/]6" (65 ram) GC912 3"(76 ram) GC912M Corte GC36 GC912/GC912M D Ancho 34Y4"(870 ram) [_33/s "...
- Page 15 11/2"(GC36) o 11/4" (GC912 y GC912M), esta pared debe ser de material no combustible (vea la nota al pie). (GC36)o 3s/16 " (GCgl 2 y GCgl 2M) = SeparaciOn m[r]ima desde la parte inferior de la 23/8"...
- Page 16 Instrucciones de Instalaci6n Conexi6n a la alimentaci6n La conexiOn de gas al producto debe utilizar el codo surninistrado con una rosca NPT Este aparato viene configurado de fa" b rica externa de 1/2" (12turn). para su empleo con Gas natural a 4"de presi0n de agua de columna.
- Page 17 Instrucdones de Instalad6n C6mo convertir el regulador entre GN ygas Desenrosque la tapa del regulador. Vuelva a colocar la tapa del regulador. Verifique la orientaci6n del tap6n pl_stico de conversi6n, y de ser necesario punto de prueba al costado del regulador). desenr6squelo, d61evuelta y vuelva a Cuando altere el regulador para diferentes enroscarlo (con la parte ancha lejos de la...
- Page 18 Instrucciones de instalaci6n la resistencia de aislamiento y la tierra Conversi6n a un tipo diferente de gas continua del circuito elF_ctrico. Los quemadores se pueden utilizar con GN o gas LP,siempre y cuando se instalen los 12 La etiqueta suministrada con los orificios orificios inyectores apropiados para el gas debe colocarse sobre la etiqueta de tipo de surninistrado.
- Page 19 Ajuste de calibraci6n minima ubicados correctamente y de acuerdo con (Nora: este diagrama representa al moddo G(912, el orificio de inyecciOn. pero es similar para el modelo GC36). Vea la Lista de Verificaci©n de Instalaci©n del Producto que se adjunta al producto.
- Page 20 [nstrucciones de instamaci6n Verificar el tipo de gas GC36 Quemado_es Orificio GN Orificio Gas Gas LP (ram) BTU(MJ/h) @ BTU (MJ/h) @ 0,15psi (4"H20) (ram) 0,41psi (11"H20) Der. trasero 1,3 mm 8,000 (8,4 MJ/h) 0,8 mm 8,000 (8,4 MJ/h) Izq. trasero...
- Page 21 So[ud6n de D_ob[emas [_1o enciende? [__ento para [_1o deja encender o de chispor, permanece Tabla de Soluci_n flama amarilla? rotear? prendido? de problemas 0oo 0o I_d_l_ _;01 ,00,,0 0 [_st&n los quemadores correctamente ensamblados? [_lectrodos sucios? [_s correcta la presi6n de gas? [_s correcto el ajuste bajo? E_alidas mal colocadas u obstruidas?
- Page 22 Avert[ssements de s cur[t Les connecteurs flexibles de I'appareil devront satisfaire aux exigences du code ANSI Z21.24 et des State Boards (aux I_.-U.). IIs ne devront pas d_passer Risque d'_lectrocution 91 cm de Iongueur. D_brancher I'alimentation _lectrique avant de proc_der _ I'entretien du produit, ATTENTION!
- Page 23 Avant de Commencer Preparation de la carrosserie Liste de v_rification des pi_ces V6rifier que le rev__ternentdu comptoir est Unit6_de base de la table de cuisson au gaz au car@ et b niveau et qu'aucun 616rnent Documentation (Kit GPL inclus) structurel n'interf__re avec I'espace requis. Rondelle bleue et coude (enrubann__sau V6rifier que le rev__tementde cornptoir cordon d'alimer]tation)
- Page 24 Rampe gaz centra/e Or f ce d'admission a_ Produit GC36 GC912/GC912M A Largeur S6 po (914 ram) 36 po (914 ram} B Profondeur 21 po (533 ram) 211/2 po (546 ram) C Hauteur lS/s po (41,5 rnrn) 2g/16po (65 ram) GC912...
- Page 25 2 1/2 po (63 ram) (GC36)ou 1/4 po (31 mm) (GCCpl 2 & GCCpl 2M) = Distance mirlimum entre le bord avant du cornptoir et le bord avant de I'appareil. Dans le cas oQ cela r6_duitla distance entre le bord arri__re de I'appareil et le tour adjacent b une valeur inf6_rieureau mirlimurn de 38 mm (GC36)ou de 31 mm (GCCpl 2 &...
- Page 26 Instructions d'installation Le coude fourni avec un filetage ext6rieur Raccord d'alimentation au gaz NPTde 12 mm dolt __treint6gr6_au raccord Cet appareil est r6g16en usine pour __tre de gaz du produit. utilis6 avec du gaz naturel sous une pression V_rifier que la rondelle bleue fournie de 10,15cm (4 po) de colonne d'eau.
- Page 27 Instructions d'installation Conversion du r_gulateur entre GN et GPL D6visser le capuchon du r6gulateur. Remettre en place le capuchon du r6gulateur. V6rifier Ibrier]tation de lafiche de conversion en plastique et, si n6cessaire, la Tester la pression du gaz (point de test d6visser, la retourner et la revisser en place fourni sur le cot6 du r6gulateur).
- Page 28 Instructions d'installation Conversion _ des types de gaz 12 II faudrait placer I'@iquette Iivr__e avec diff_rents lesorifices sur I'__tiquettedu type de gaz les br(]leurspeuvent_tre utilis6savecdu gaz existant pour refl__terle changernent. naturelou des GPL a condition que lesorificesde I'irjecteur appropri_sau gaz fournissoientinstall6s. Pourchanger lesorificesde I'injecteur,vous aurez besoind'une cl6 b pipe de 7 turn (9/32e po).
- Page 29 Ajustement du r_glage minimum anomalie, v__rifierqu'ils sont bien en place (Remarque : Ce sch6ma correspond au mod61e G(912, et align__savec Ibrifice de I'injecteur. mais il est similaire au module GC36). Voir la liste de v6rification de I'installation du produit ci-jointe.
- Page 30 Instructions d'installation V_rification du type de gaz GC36 BrQ_eurs Orifice GN Orifice GPL (ram) BTU(MJ/h) @0,1S (ram) BTU (MJ/h) @ 0,41 psi (102 mm d'eau) psi (280 mm d'eau) Arri_re droit 1,3 mm 8 000 (8,4 MJ/h) 0,8 mm 8 000 (8,4 MJ/h)
- Page 31 O_pannage Allumagelent Allumage letincelles Dispari- ou flammes d_ficient? conti- tion jaunes? nues? de la D_pannage flamme? iiiiiiiiii@!i!!#!}iiii!#iiiiiiiii#iiiiiiiiiii#iiiiii_ ii//@_S_iiiiii!iiiiiiiii//i}ii{iiii iiiiil;@@!i!!!!!!!!!#!!!!!!!!S!!!!!!!!!!!!ii#!i#i# iii/iiiiii#i;i iiiiiiii!#iiiiiiiiiil To i Les brE_leurs sont-ils assembles correctement? ii !i!i!i}}ili Les _%lectrodes sont-ils sales? La pression du gaz est-elle adequate? Le r_%glage de faible intensity% est-il correct? Lejet de la flamme...
Need help?
Do you have a question about the GC36 and is the answer not in the manual?
Questions and answers