this has been set at the iactory
but cau be checked
after the correct
pressure
has been reached.
[ o adjust
Jor
IT_il_ilTltllT_ setting,
if ne(2tJed. YoLl wilt need a 7/64" diameter
x t 3/4" [2.5 x 45mini
screwdriver.
1.
Remove
the knobs.
2.
tguite the burner
and set the
kuob
to its i_]iniimm] position.
3.
Rotate theturu
down screw (dowu the hole iu the shafl].
Rotate slowly
LmtiJa millimLli'q
regular
lJal'qe is achieved.
(the lJal'qe wilt diminish
when the
screw
is tLlrlletJ
ctocl<wise
anti
increase
wheu
tLlrlletJ
co=inter
clockwise).
4.
When
the settiug
is right check
regulation
by quickly
rotatiug
the knob item the maxhTltllT_ to
the mh_hT_tlm delivery
position.
[he flame mtist not go oLlt. Replace the knob.
Buruers
can be used with all types of gas, provided
that the orifice appropriate
for the gas
delivered
are installed.
(Use a _/s2" [7mm]
socket.)
1o change
the oriike:
1.
turn oflthe
I'liahls su[)l)ty.
2.
Ensure all gas valves are turued
off.
3.
Remove all buruer
heads.
4.. Unscrew
the oriiices
and replace them with the correct
ones. (Size numbers
stamped
on side
e.g. 70 = 0.70mm.)
5.
Reset miuimum
settiug (see above).
6.
Save the oriii(es
rel'liove(J l]om the product
lot luture
use.
the label SUpl_lied
with the orifice
can be placed
over
the existing
gas type label to indicate
the
change.
t tigh Altitude
orifices
are available
from tisher
& Payke[ USA (see address on front cover).
NG Kit Part No. 5_ 1566
[ P Kit Part No. Sgt 567
|
,I
,
i
I IMPORTANT!
Pteas_ make tills imormation
aw_itabk
to th_ I_ rson re,; _onsibte
ior installing
[this
cooktop
as it cotlJ(J r( (JLIC( yotll
installation
costs.
1
To the Installer:
Please leave these instrLlctions
with the apl_iiance,
tniorm the customer
to
retah_
1or Jut[ire
ie_(?l-el_ce.
j CAUTION"
IN ORDER
TO AVOID
A HAZARD
THESE APPLIANCES
MUST
BE
m
i
INSTALLED
ACCORDING
TO THESE
INSTRUCTIONS
FOR INSTALLATION.
"
Please follow
installation
information
carefully,
tf in doubt
(onsult your
local building
regulations,
local gas authority
codes and electrical
regulations.
°
the appliance
is to be installed
only by an authorized
person.
DO
Ensure the couutertop
is square an(J level an(J ensure no structural
members
il_terl(_re with
sl)ace
req
tlh-el'ftel_tS.
DO
EItSLII'e that there is a Dower supply
receptacle
withiu
reach of the cooktop
power cord
(30" item
the middle
of the [)ro(Juct).
the main cable should
not touch
any hot metal
[)arts.
DO
Make sure the cooktop
is conl_ected
to a power SUpl_Jy socket that is electrically
groLill(Je(J
iu accordauce
with
local codes or in the absence
of local codes, with the National
Electric
Code ANSI/FPA
70 or CSA 22.2 ((anada).
DO
Make the countertol)
of a heat resistant
material.
°
[his appliance
shall be installed
in accordance
with
the iustaliation
requirel'nel_ts
of the
local gas authority
or the appropriate
iustaJJation code or ill the absence
of Jot:a[ codes with
the latest National
Fuel Gas Code ANSI Z22g. t or CAN Bt4!).t,2
(Canada).
"
Disconuect
power before serviciug
Lmit.
"
Be aware of sharp edges when
handling
stainless steel products.
"
When
this appliance
is installed
it shall not be used as a space heater.
"
No combustible
material
or productsshoukJ
be placed
on this apptiauce
at any time.
"
Do not spray aerosols
in the vicinity
of this apidiance
while
it is in operation.
I or replacement
parts
or if further
hel I) is needed
concerning
this
appliance
(:all:
TOIl
IREE I 88891NPUSA
(I 888
9¢6 7872)
or write
to:
I isher
& Paykel
Ai)l)liances
Inc.,
27 I hlbble,
Ivine
CA 92618
or contact
us through
our web
site,
www.iisherpaykel.com
Part No. 599078
issue A
Jalltlar
3
2001
Need help?
Do you have a question about the GC901 Series and is the answer not in the manual?
Questions and answers