Motorola RS507 Quick Reference Manual
  1. Manuals
  2. Brands
  3. Motorola Manuals
  4. Barcode Reader
  5. RS507 Series
  6. Quick reference manual

Motorola RS507 Quick Reference Manual

Hands-free imager
Hide thumbs Also See for RS507:
Table of Contents

Advertisement

Quick Links

RS507 Hands-Free Imager
Quick Reference Guide

Advertisement

Table of Contents
loading

Related Manuals for Motorola RS507

Summary of Contents for Motorola RS507

  • Page 1 RS507 Hands-Free Imager Quick Reference Guide...

  • Page 2: Warranty

    RS507 Hands-Free Imager © 2009 MOTOROLA, INC. All rights reserved. Motorola reserves the right to make changes to any product to improve reliability, function, or design. Motorola does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.

  • Page 3: About This Guide

    Quick Reference Guide Introduction The RS507 Hands-Free Imager (also referred to as the Imager) is a wearable bar code scan solution for both 1D and 2D bar code symbologies. The Imager is also compatible with a wide range of mobile computers communicating over Bluetooth.

  • Page 4: Unpacking The Imager

    (10 mil and above). DL is recommended in electronics, pharmacy or when handling small items. Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact Motorola Enterprise Mobility Support immediately. See Service Information on backcover...

  • Page 5: Cordless Configuration Features

    Quick Reference Guide Cordless Configuration Features Trigger Configuration Battery Release Latch Imager Window Battery Comfort Pad Trigger Swivel Assembly Finger Strap Scan Trigger Restore Key Asset Control Label Left Scan LED Strap Buckle Beeper Right Scan LED Triggerless Configuration Triggerless Strap Holder...

  • Page 6: Corded Configuration Features

    RS507 Hands-Free Imager Corded Configuration Features Interface Cable Connector to WT4090 Release Latch Imager Window Corded Adapter Comfort Pad Trigger Swivel Assembly Finger Strap Scan Trigger Asset Control Label Restore Key Strap Buckle Left Scan LED Beeper Right Scan LED...

  • Page 7: Change Trigger Position

    Quick Reference Guide Change Trigger Position The Trigger Swivel Assembly of the Imager rotates to provide left-hand or right-hand use. From the bottom of the Imager, hold and pull the Comfort Pad out of the Imager. Finger Strap Note: It is not necessary Comfort Pad to remove the Finger Strap from the Trigger...

  • Page 8: Install The Battery

    RS507 Hands-Free Imager Getting Started - Cordless Configuration Charge the Battery Before using the Imager, charge the battery. The 8-Bay Battery Charger supports both standard and extended capacity batteries. To charge the Imager battery, refer to the SAC5070 8-Bay Battery Charger Quick Reference Guide, p/n 72-11589-01 available at: www.motorola.com/enterprisemobility/manuals.

  • Page 9: Getting Started - Corded Configuration

    Quick Reference Guide Tighten the Finger Strap. Finger Strap NOTE When using the Imager for the first time, after power up, press and release the Scan Trigger to enable the manual triggering mode (this operation disables the default auto triggering mode). Getting Started - Corded Configuration In order to start using the Imager you must install the Corded Adapter.

  • Page 10: Connect To A Wearable Terminal

    RS507 Hands-Free Imager Connect to a Wearable Terminal The Imager connects to a terminal and mounts on the fingers. To connect the Imager to the Terminal Interface Connector terminal: Interface Cable Connector On the terminal, remove the cover from the Terminal Interface Connector.

  • Page 11: Status Indications

    Quick Reference Guide Status Indications The Imager has two Scan LEDs that provide identical indications. The Imager is also equipped with a beeper that generates sound indications in variable tones. NOTE In the corded configuration, beep indications are emitted only from the connected terminal.

  • Page 12: Remove Bluetooth Connection

    RS507 Hands-Free Imager Bluetooth Connection Establish Bluetooth Connection To establish Bluetooth connection with a mobile computer: Ensure that the Imager is within a range of 10 meters (30 feet) from the mobile computer. Install the battery in the Imager. Launch the Bluetooth Device (BD) Address application on the mobile computer.
  • Page 13 Quick Reference Guide Ensure that the mobile computer is “on and awake” (not in Suspend mode). The Imager automatically attempts reconnecting to the mobile computer for 30 seconds (Scan LED flashes green). If automatic re-connection fails, verify that the Imager is within Bluetooth range and briefly press the Restore Key on the Imager to reconnect.

  • Page 14: Scan Triggering Modes

    The Imager can also be configured to a single or continued scan operation. The motion and proximity features are enabled by default and can be re-configured by the user (see RS507 Hands-Free Imager Product Reference Guide, p/n 72E-120802-01).

  • Page 15: Aiming The Imager

    Quick Reference Guide One green flash of the Scan LED and a high beep indicates that a bar code was properly decoded. NOTE In some applications, proper decoding of a bar code is indicated by a software application running on the mobile computer. Aiming the Imager The aiming pattern of the Imager is a cross hair laser beam with bright center dot (shown below).

  • Page 16: Changing Triggerless To Trigger Configuration

    RS507 Hands-Free Imager NOTE When using the application on your mobile computer in “Pick List” mode, the Bright Center Dot can be positioned anywhere on the symbol. @1234@ @1234@ Right Wrong The aiming pattern is smaller when the Imager is closer to the symbol and larger when it is farther from the symbol.

  • Page 17: Changing The Imager Behavior

    Changing the Imager Behavior The Imager operation can be configured by scanning custom bar code tables. The following table provides examples of configurable Imager features. For more information, refer to the RS507 Hands-Free Imager Product Reference Guide, p/n 72E-120802-01. Feature...

  • Page 18: Resetting The Imager

    RS507 Hands-Free Imager Feature Description Default Setting Bluetooth The Imager automatically tries to reconnect Back in Bluetooth auto connect. to a remote device when a disconnection range. occurs that is due to the radio losing communication. This can happen if the Imager goes out of the mobile computer range.

  • Page 19: Troubleshooting

    Quick Reference Guide Troubleshooting Problem Cause Solution Laser aiming Corded: Interface Verify that the interface cable is properly connected. pattern does not cable is not secure. display when Cordless: Battery is Replace or charge the battery. pressing the Scan not charged. Trigger.

  • Page 20: Field Replaceable Parts

    RS507 Hands-Free Imager Field Replaceable Parts Part Description Trigger Swivel Assembly. KT-CLMPT-RS507-01R Set of 10 Strap Buckles. KT-BKL-RS507-10R Triggerless Strap Holder. KT-CLMPN-RS507-01R Set of 10 Comfort Pads. KT-PAD-RS507-10R Set of 10 Triggerless Finger Strap with KT-STRPN-RS507-10R Finger Support. Set of 10 Trigger Finger Strap with Finger KT-STRPT-RS507-10R Support.

  • Page 21: Comfort Pad Replacement

    Quick Reference Guide Comfort Pad Replacement Removal Flip the Imager over, such that the bottom of the Imager and the Comfort Pad are facing upwards. Insert the tip of your finger under the edge of the Comfort Pad at the back of the Imager. Lift the Comfort Pad upwards and remove it from the Imager.

  • Page 22: Triggerless Strap Holder Replacement

    RS507 Hands-Free Imager Installation Turn the Imager upside-down. Position the Trigger Swivel Assembly to align with the back of the Imager. Lower the Trigger Swivel Assembly to the Imager. Rotate Trigger Swivel Assembly 1/4 turn counterclockwise. Press the Comfort Pad onto the Imager. When properly installed, the Comfort Pad “locks”...

  • Page 23: Finger Strap Replacement (Trigger Swivel Assembly)

    Quick Reference Guide Installation Turn the Imager upside-down. Position the Triggerless Strap Holder to align with the back of the Imager. Lower the Triggerless Strap Holder to the Imager. Rotate Triggerless Strap Holder 1/4 turn counterclockwise. Finger Strap Replacement (Trigger Swivel Assembly) Removal Remove the Finger Strap from the...

  • Page 24: Finger Strap Replacement (Triggerless Strap Holder)

    RS507 Hands-Free Imager Finger Strap Replacement (Triggerless Strap Holder) Removal Remove the Finger Strap from the Strap Buckles. Installation Slip the Finger Strap through the Strap Buckles. Triggerless Strap Holder Strap Buckle Replacement Strap Buckles Removal Strap Remove the Trigger Swivel...

  • Page 25: Regulatory Information

    ("Motorola"). This guide applies to Model Number RS507. All Motorola devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following website: www.motorola.com/enterprisemobility/support.

  • Page 26: Warnings For Use Of Wireless Devices

    RS507 Hands-Free Imager Health and Safety Recommendations Ergonomic Recommendations CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.

  • Page 27: Other Medical Devices

    "International" human exposure to electromagnetic fields refer to the Motorola Declaration of Conformity (DoC) at: www.motorola.com/enterprisemobility/doc Handheld Devices This device was tested for typical body-worn operation. Use only Motorola tested and approved belt-clips, holsters, and similar accessories to ensure EU Compliance.

  • Page 28: Laser Devices

    RS507 Hands-Free Imager US and Canada Handheld Devices This device was tested for typical body-worn operation. Use only Motorola tested and approved belt-clips, holsters, and similar accessories to ensure FCC Compliance. The use of third-party belt-clips, holsters, and similar accessories may not comply with FCC RF exposure compliance requirements, and should be avoided.

  • Page 29: Imager Labeling

    Contact a qualified Taiwanese recycler for proper battery disposal. Battery Information Motorola rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations to how long a battery can operate or be stored before needing replacement.
  • Page 30 RS507 Hands-Free Imager Standard warranty period for all Motorola batteries is 3 months, regardless if the battery was purchased separately or included as part of the mobile computer or bar code scanner. For more information on Motorola batteries, please visit: http://mysymbolcare.symbol.com/battery/batbasics1.html...

  • Page 31: Radio Frequency Interference Requirements-Fcc

    Quick Reference Guide In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user: Radio Frequency Interference Requirements-FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

  • Page 32: Marking And European Economic Area (Eea)

    Korea Warning Statement for Class B ITE Other Countries Declarações Regulamentares para RS507 - Brazil Note: The certification mark applied to the RS507 is for Restrict Radiation Equipment. This equipment operates on a secondary basis and does not have the...
  • Page 33 For more information consult the website www.anatel.gov.br. Nota: "A marca de certificação se aplica ao Transceptor, modelo RS507. Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário."...
  • Page 34 Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorola al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: www.motorola.com/recycling/weee.
  • Page 35 Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Motorola-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa www.motorola.com/recycling/weee. Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Motorola för återvinning. Information om hur du returnerar produkten finns på www.motorola.com/recycling/weee.

  • Page 36: Service Information

    1-800-927-9626 http://www.motorola.com MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners. © Motorola, Inc. 2010...

Table of Contents