Sartorius SIWABBP Operating Instructions Manual page 60

Averaging (Animal Weighing) Application V
Preparation
§ Switch on the scale: Press the e key
§ While all segments are lit, press the
) key
§ Select the Setup menu: Press the
k key repeatedly until appl is
displayed
§ Confirm appl: Press the ) key
§ Select the Animal Weighing application:
Press the k key repeatedly and
confirm with the ) key
Application Parameters: Animal Weighing
3. 6. Minimum load for start
3.6.1* 1 digit
3.6.2 2 digits
3.6.3 5 digits
3.6.4 10 digits
3.6.5 20 digits
3.6.6 50 digits
3.6.7 100 digits
3.6.8 200 digits
3.6.9 500 digits
3.6.10 1000 digits
3.18. Start of averaging
3.18.1* Manual
3.18.2 Automatic
3.19. Animal activity
3.19.1 0 .1% of the animal/
object
3.19.2* 0 .2% of the animal/
object
3.19.3 0 .5% of the animal/
object
3.19.4 1% of the animal/object
3.19.5 2% of the animal/object
3.19.6 5% of the animal/object
3.19.7 1 0% of the animal/
object
3.19.8 2 0% of the animal/
object
3.19.9 5 0% of the animal/
object
3.19.10 1 00% of the animal/
object
3.20. Auto Results printout
3.20.1* Off
3.20.2 On
3.21. S tatic display of result after load
removed
3.21.1* D isplay is fixed until
unload threshold
reached
3.21.2 F ixed display until c
is pressed
* = Factory setting
§ Save the settings with the ) key and
exit Setup: Press the ( key several
times.
60 Signum 1-2-3
Minimum load
The minimum load required for
initialization of the averaging routine
is configured in Setup under:
Appl: V: 3.6.
Signum ® 3:
:
appl1
:
anim.wg 3.6.
Setting a minimum load for averaging
can be especially useful if you configure
automatic start of measurement.
The minimum load required for
automatic taring of the container
weight on the platform (first weight),
or for automatic printout of results,
is configured in Setup under:
Appl: V: 3.5.
® 3:
Signum
a.tare
: :
appl 3.5.
You can choose from the following
10 levels for this setting:
1 digit
2 digits
5 digits
10 digits
20 digits
50 digits
100 digits
200 digits
500 digits
1000 digits
The "digits" here refer to the scale
intervals in the connected weighing
platform. If the interval of the
connected platform is 1 g, for example,
and 1000 digits are required, you must
place at least 1000 g (= 1000 intervals
=1000 digits) on the weighing platform
to start the averaging routine.
Starting the Measurements
The averaging routine does not begin
until the fluctuation in weight value
remains below a defined threshold
over three consecutive measurements.
The tolerance limit is defined as a
percentage of the animal or
object weight (for example, 0.1%, 0.2%,
..., 50%, 100%), configured in Setup
under:
Appl: V: 3.19.
® 3:
Signum
:
appl1
:
anim.wg 3.19.
If the "Averaging" parameter is set to
2%, for example, and the animal or
object weighs 10 kg, measurement
does not begin until the fluctuation
in weight value remains below 200 g
during three consecutive measurements.
Display
A calculated average value is shown
continuously on the main display.
The ! symbol (indicating a calculated
value) is also displayed.
You can toggle between this display to
a readout of the current weight on the
platform by pressing the w key.
In the Setup menu, under:
Appl: V: 3.21.
® 3:
Signum
:
appl1
:
anim.wg 3.21.
You can select "Display is static until
unload threshold reached" to have the
display switch automatically to the
weight readout when you unload the
weighing platform (i.e., when the load
is less than half the minimum load).
The result of the most recent averaging
operation is not saved.
If you select "Display is static until
the c key is pressed," the calculated
average remains displayed even after
the weighing platform is unloaded,
until you press the c key to begin
a new measurement.