Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
HB0119
IK700 SERIES
INTENDED FOR DOMESTIC COOKING ONLY
!
!
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION
ON PAGES 15
17.
TO
Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville QC J2C 7W9
1-800-567-3855
REGISTER YOUR PRODUCT ONLINE AT: www.bnv.ca
For additional information, visit
www.venmar.ca
21227 rev. 02
Advertisement
Table of Contents
Related Manuals for Venmar Ispira IK700 Series
Summary of Contents for Venmar Ispira IK700 Series
-
Page 1: Installation Instructions
READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 15 Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville QC J2C 7W9 1-800-567-3855 REGISTER YOUR PRODUCT ONLINE AT: www.bnv.ca For additional information, visit www.venmar.ca... - Page 2 9. To reduce the risk of fire and electrical shock, b) Always turn hood ON when cooking at high the Venmar Ispira IK700 series models heat or when flambeing food (i.e.: Crêpes should only be installed with their own built-in Suzette, Cherries Jubilee, Peppercorn Beef blower.
-
Page 3: Table Of Contents
WARNING This hood is equipped with an RF receiver (optional remote control sold separately). Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this product. The remote control has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and the Canadian ICES-003. -
Page 4: Install Ductwork
19325 (sold separately). Installation over a gas range: 1" M Refer to gas range manufacturer’s guidelines for the recommended CFM. If two IK700 Series range hoods are required, the space between both hoods should not be less than 1” . HH0154A... -
Page 5: Prepare The Installation
2. PREPARE THE INSTALLATION WARNING When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: - Hood - Accessories... -
Page 6: Prepare Hood
3. PREPARE HOOD 1. Rest the range hood on a table. Use a piece of cardboard to avoid damaging the table or the hood. Remove tape on filters. Remove filters by pushing them towards the back of the hood (opposite to control side) and flipping them up, then set filters aside. -
Page 7: Measure Installation
4. MEASURE INSTALLATION EILING LOWER BOTTOM Determine angle brackets length needed ⁄ " based upon ceiling height (B) and desired ANGE HOOD height of hood above cooktop (A). BOTTOM The table below indicates which flue(s) to use and the number of brackets required according to height (C). -
Page 8: Install Mounting Bracket
5. INSTALL MOUNTING BRACKET WARNING When building framework, always follow all applicable construction codes and standards. 10¼" 1. Modify ceiling stucture over hood RAMING INNER EDGE location. Install 2" x 4" cross framing ⁄ " 10 ⁄ " 10¼" between ceiling joists using ceiling mounting bracket dimensions shown at . -
Page 9: I Nstall Mounting Bracket
5. INSTALL MOUNTING BRACKET (CONT'D) 8” ROUND DUCTWORK 3. Remove both screws retaining the ceiling mounting bracket to the top of the hood. RONT OF HOOD Discard screws. Position the mounting plate in such a way that one of the sides without a “T” will be facing the front of the hood. -
Page 10: Assemble Angle Brackets
6. ASSEMBLE ANGLE BRACKETS 1. Assemble 4 angle brackets to the ceiling mounting bracket using at least two no. 10-32 x 1/2" quadrex screws per angle bracket. NOTES: 1. Do tighten screws yet. 2. Depending on the height needed (previously determined in section 4), the angle brackets might not touch the ceiling as... -
Page 11: Connect Wiring
6. ASSEMBLE ANGLE BRACKETS (CONT'D) IDE VIEWS OF THE BLOWER BOX RONT ORRECT OF THE HOOD 4. Make sure all brackets are straight and blower box is level and square (as shown at right), then tighten all screws. RONT OF THE NCORRECT HOOD HD0420... - Page 12 CONNECT WIRING (CONT'D) 3. Run house wiring through wire clamp and into blower box electrical box. Tighten wire clamp to secure house wiring cable to blower box. 4. Measure the required length of 8" round metal duct OUSE from the adapter/damper to the ductwork rough-in in the ceiling.
-
Page 13: Install Glass Panels
8. INSTALL GLASS PANELS (WG MODEL ONLY) The WG hood model glass panels are sold separately and have to be installed before completing the hood installation. For each glass panel: 1. Carefully remove glass panel from its packaging. Remove glass panel nuts (factory installed) from both studs and set aside. 2. -
Page 14: Install Hood
9. INSTALL HOOD (CONT'D) 2. Slide hood over blower box and attach to blower box using the 4 screws previously removed in step 3.3 (some parts not illustrated to ease understanding). NOTE: For more convenience, a total of 16 holes (4 holes per section) are available to secure the hood, but only 1 screw per section is necessary. -
Page 15: Reinstall Hybrid Filters
10. REINSTALL HYBRID FILTERS CAUTION Remove protective plastic film covering filters before reinstalling them. Rest rear filters edge on filter springs in the range hood. Tilt up the filters into position. Make sure filter tabs are securely engaged in range hood front edge slots after installation. -
Page 16: Care
12. CARE (CONT'D) TAINLESS STEEL Don’t: • Regularly wash with clean cloth or rag • Use any steel or stainless steel wool or any soaked with warm water and mild soap or other scrapers to remove stubborn dirt. liquid dish detergent. •... - Page 17 13. OPERATION (CONT'D) A. D ELAY UTTON ONTROL OUBLE UNCTION UTTON CONT ii. When the blower is off, it is possible to lock the control interface in order to clean the glass panel. To lock the control interface: Press and hold this button for 2 seconds. The button will light to its high intensity and flash three times, it will then stay on its mid intensity to indicate that the control interface is locked.
-
Page 18: Wiring Diagram
ARTS AND EPAIRS In order to ensure your unit remains in good working condition, you must use Venmar Ventilation ULC genuine replacement parts only. Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of safety. -
Page 19: Service Parts
15. SERVICE PARTS ART NO ESCRIPTION SV09958XX* RONT LASS ANEL 21221 OWER SV20816 FOR REMOTE CONTROL 09550 LECTRONIC ONTROL 09022 RANSFORMER 62248 DRIVER AND CONNECTION HARNESS 62612 MODULE 62240 13.38” 5.15” x 0.5” (1) YBRID FILTER SV09959XX* LASS ANEL SV08582 NTERNAL BLOWER 08543 8”... -
Page 20: Warranty
To contact Venmar Ventilation ULC warranty service, call 1-800-567-3855 in Canada. In order to qualify for a warranty claim, the owner of a Venmar Ispira IK700 Series range hood must have the model and serial number along with a proof of the original purchase date. At the time of requesting service, describe the nature of any defect in the product or part.
Need help?
Do you have a question about the Ispira IK700 Series and is the answer not in the manual?
Questions and answers