READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 15 TO 18. Venmar Ventilation Inc., 550 Lemire Blvd., Drummondville QC J2C 7W9 1-800-567-3855 REGISTER YOUR PRODUCT ON LINE AT: www.bnv.ca For additional information, visit www.venmar.ca or www.ispira.ca...
Page 2
Always turn hood ON when cooking at high heat To reduce the risk of fire and electrical shock, the or when flambeing food (i.e.: Crêpes Suzette, Venmar Connaisseur CIC700 Series models Cherries Jubilee, Peppercorn Beef Flambé). should only be installed with their own built-in Clean ventilating fans frequently.
1. INSTALL DUCTWORK ( ’ CONT Installation over a gas range: 1" M Refer to gas range manufacturer’s guidelines for the recommended CFM. If two CIC700 Series range hoods are required, the minimum space between the hoods should not be less than 1”. HH0154A 2.
3. PREPARE HOOD 1. Rest the range hood on a table. Use a piece of cardboard to avoid damaging the table or the hood. Remove tape on filters. Lift filters by pushing them towards the back (opposite control side) and rotate, then set filters aside. HO0194 2.
4. MEASURE INSTALLATION EILING LOWER BOTTOM Determine angle brackets length needed ⁄ " based upon ceiling height (B) and desired ANGE HOOD height of hood above cooktop (A). BOTTOM The table below indicates which flue(s) to use and the number of brackets required according to height (C).
5. INSTALL MOUNTING BRACKET WARNING When building framework, always follow all applicable construction codes and standards. 10¼" 1. Modify ceiling stucture at hood location. Install 2" x 4" cross framing between ceiling joists ⁄ " 10 ⁄ " 10¼" using ceiling mounting bracket dimensions shown at right.
5. INSTALL MOUNTING BRACKET ( ’ CONT 8" R OUND DUCTWORK 3. Position the mounting bracket in such a way that one of the sides without a “T” will be facing the RONT front of the hood. Secure mounting OF THE HOOD bracket to the ceiling using 8 no.
6. ASSEMBLE ANGLE BRACKETS 1. Assemble 4 angle brackets to the ceiling mounting bracket using at least two no.10-32 x 1/2" quadrex screws per angle bracket. NOTES: 1. Do not tighten the screws yet. 2. Depending on the height needed (C) (previously determined in section 4), the angle...
6. ASSEMBLE ANGLE BRACKETS ( ’ CONT IDE VIEWS OF THE BLOWER BOX RONT OF THE CORRECT HOOD 4. Make sure all brackets are straight and blower box is level and square (as shown at right), then tighten all screws. RONT OF THE INCORRECT...
Page 11
7. CONNECT WIRING ( ’ CONT 3. Run house wiring through wire clamp and into blower box electrical box. Tighten wire clamp to secure house wiring cable to blower box. 4. Measure the required length of 8" round metal duct from the adapter/damper to the ductwork rough-in in the ceiling.
8. INSTALL GLASS PANELS ( WG MODEL ONLY The WG hood model glass panels are sold separately and have to be installed before completing the hood installation. For each glass panel: 1. Remove glass panel from its packaging. Remove glass panel nuts (factory installed) from both studs and set aside. 2.
9. INSTALL HOOD ( ’ CONT CREW LOCATIONS 2. Slide hood over blower box and attach to blower box using the 4 screws previously removed from step 3.3 (some parts not illustrated to ease understanding). NOTE: For more convenience, a total of 16 holes (4 holes per section) are available to secure the hood, but only 1 screw per...
10.REINSTALL BAFFLE FILTERS CAUTION Remove protective plastic film covering filters before reinstalling them. 1. Using a Phillips no. 2 screwdriver, assemble two knobs to each filter. The screws MUST BE on filter tabs side. See illustration at right. HO0193 2. Rest rear filters edge on filter springs in the range hood.
12. CARE WARNING Before servicing or cleaning the unit, switch power off at service panel and lock service panel to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. AFFLE ILTERS Baffle filters should be cleaned monthly.
Page 16
13. OPERATION ( ’ CONT HC0052 Blower Delay/Control Lock button D) Blower medium-high speed button Blower low speed button — LinkLogic Auto Link Mode button ® — LinkLogic Erase Link button Blower high speed button ® C) Blower medium-low speed button —...
Page 17
13. OPERATION ( ’ CONT G. L IGHT UTTON ACKLIGHTING OLOR OUBLE UNCTION UTTON i. This button allows four different lighting levels according to your needs. Press once for full intensity, twice for intensity level 3, three times for intensity level 2 and once more for nightlight.
To contact Venmar Ventilation Inc. warranty service call 1-800-567-3855 in Canada. In order to qualify for a warranty claim, the owner of a Venmar Connaisseur CIC700 Series range hood must have the model and serial number along with a proof of the original purchase date. At the time of requesting service, describe the nature of any defect in the product or part.
ARTS AND EPAIRS In order to ensure your unit remains in good working condition, you must use Venmar Ventilation Inc. genuine replacement parts only. Venmar Ventilation Inc. genuine replacement parts are specially designed for each unit and are manufactured to...
Need help?
Do you have a question about the Connaisseur CIC700 Series and is the answer not in the manual?
Questions and answers