Download  Print this page

Programming The Water Softener (models Whes30 & Whes33) Customizing Features / Options; Programming Whes30 & Whes33 Water Softener - Whirlpool WHES33 Installation And Operation Manual

Demand controlled water softener.
Hide thumbs

Advertisement

Table of Contents
Programming the Water Softener
SET SALT LEVEL
button
STATUS LIGHT
(see below)
RECHARGE button
STATUS LIGHT (Model WHES33 Only)
When the WHES33 water softener is connected to
electrical power, the status light on the control panel
will be on or flashing, as follows:
Light flashing rapidly, with "CURRENT TIME"
=
shown in the display and the clock flashing
slowly - The present time needs to be set, either
during initial start up or after a long power outage.
See "Set Time of Day", at right.
Light flashing slowly, along with the salt level
=
indicators in the display - The salt monitor sys-
tem indicates a low salt level and needs to be set.
See "Set Salt Level" on Page 17.
Light flashing rapidly, with "Err" shown in the
=
display - The electronic self-diagnostics have
detected a problem. See "Troubleshooting" on
Page 22.
Light on steady (not flashing) - The system has
=
power applied and does not require any attention.
PROGRAM THE SOFTENER
When the transformer is plugged into the electrical
outlet, the model code ("LE31" fro Model WHES30 or
"LE33" for Model WHES33) and a test number (exam-
ple: J3.0), are briefly shown in the display. Then the
words "CURRENT TIME" appear and 12:00 PM
begins to flash.
Questions? Call Toll Free 1-866-986-3223
When you call, please be prepared to provide the model and serial number,
found on the rating decal, typically located on the rim below the salt lid hinges.
(Models WHES30 & WHES33)
Display
SET
SALT
LEVEL
PRESS TO SCHEDULE
OPERATING (Steady)
LOW SALT (Flashing)
HOLD TO START
RECHARGE
DOWN button
or visit www.ecodynewatertreatment.com
UP button
PROGRAM
PROGRAM button
SET TIME OF DAY
If the words "CURRENT TIME" do not show in the
display, press the PROGRAM button until they do.
1. Press the
UP or
present time. Up moves the display ahead; down
sets the time back. Be sure AM or PM is correct.
NOTE: Press buttons and quickly release to slowly
advance the display. Hold the buttons down
for fast advance.
SET WATER HARDNESS NUMBER
1. Press the PROGRAM button once again to display
a flashing "25" and the word "HARDNESS".
Monday- Friday, 8 AM - 7 PM EST
15
FIG. 26
s
DOWN buttons to set the
FIG. 27
FIG. 28
continued on next page

Advertisement

Table of Contents

   Also See for Whirlpool WHES33

   Related Manuals for Whirlpool WHES33

This manual is also suitable for:

Whes30Whes20

Comments to this Manuals

Symbols: 0
Latest comments:
  • Caroline Mar 12, 2020 03:21:
    Can I schedule a weekly recharge on the WHES33 or only daily?
  • William greene Apr 09, 2019 03:56:
    How much water should be in bottom of tank man is about 1/4 1/3 full from bottom over slat level that is just at bottom of the nunmber 2
  • Kathleen Jun 13, 2018 10:13:
    Tank fills with water and does not go down. I have cleaned venturi, which really was not dirty but cleaned anyway as instructed by phone troublesho​oter.Recha​rged but water still in tank.
  • Troy Jan 23, 2018 10:11:
    What does it mean when it says service fill on model #whes33 le33 and how do you correct it ,water level does not go down in tank
  • Troy Jan 23, 2018 10:11:
    What does it mean when it says service fill on model #whes33 le33 and how do you correct it ,water level does not go down in tank