Download  Print this page

Whes20 Customizing Features/options - Whirlpool WHES33 Installation And Operation Manual

Demand controlled water softener.
Hide thumbs

Advertisement

Table of Contents
Programming the
Water Softener
(Model WHES20)
SET RECHARGE (REGENERATION) TIME
1. Press the PROGRAM button once again to display
a flashing "2:00AM" and the words "RECHARGE
TIME". This is a good time for the recharge to start
in most households, because water is not in use.
2. If you want to change the recharge start time,
s
press the
UP or
desired time shows. Be sure AM or PM is correct.
3. Press the PROGRAM button once again, to return
to the normal time of day display.
START A RECHARGE
1. Press the RECHARGE button and hold for three
seconds, until "RECHARGE" begins to flash in the
display, starting a recharge. This recharge draws
the sanitizing bleach into and through the water
softener. Any air remaining in the water softener is
purged to the drain. During this time, periodically
check for leaks.
NOTE: As with all other water system applications,
leaks may occur. Leaks may not be immedi-
ately apparent. Recheck for leaks 24 hours
after first recharge cycle is complete.
POWER OUTAGE MEMORY
If electrical power to the water softener is lost, "mem-
ory'' built into the timer circuitry will keep all settings
for several hours. While the power is out, the display
is blank and the water softener will not regenerate.
When electrical power is restored, the following will
occur:
Reset the present time only if the display is flashing.
The HARDNESS and RECHARGE TIME never
require resetting unless a change is desired. Even if
the clock is incorrect after a long power outage, the
softener operates as it should to keep your water soft.
However, regenerations may occur at the wrong time
of day until you reset the clock to the correct time of
day.
NOTE: If the water softener was regenerating when
power was lost, it will now finish the cycle.
FIG. 18
DOWN buttons until the
Customizing
Features / Options
(Model WHES20)
RECHARGE NOW
The RECHARGE button is used to initiate an immedi-
ate recharge.
1. Press and hold the RECHARGE button until the
words "RECHARGE NOW" flash in the display.
RECHARGE NOW initiated
The softener enters the fill cycle of regeneration right
away. "RECHARGE NOW" will flash during the
regeneration. When completed, full water condition-
ing capacity is restored. While water softener is run-
ning a recharge, the time remaining until the recharge
is completed will show in the display during all cycles
except for the Fill cycle.
NOTE: Avoid using hot water while the softener is
regenerating, because the water heater will
refill with bypass hard water.
RECHARGE TONIGHT
If you do not want to start an immediate recharge, but
would like to schedule an extra recharge at the next
preset recharge time, do the following:
1. Press and release (do not hold) the RECHARGE
button.
RECHARGE TONIGHT initiated
The words "RECHARGE TONIGHT" flash in the dis-
play, and the softener will recharge at the next
recharge time. The words "RECHARGE NOW" will
flash during the regeneration. When completed, full
water conditioning capacity is restored.
13
FIG. 19
FIG. 20

Advertisement

Table of Contents

   Also See for Whirlpool WHES33

   Related Manuals for Whirlpool WHES33

This manual is also suitable for:

Whes30Whes20

Comments to this Manuals

Symbols: 0
Latest comments:
  • Caroline Mar 12, 2020 03:21:
    Can I schedule a weekly recharge on the WHES33 or only daily?
  • William greene Apr 09, 2019 03:56:
    How much water should be in bottom of tank man is about 1/4 1/3 full from bottom over slat level that is just at bottom of the nunmber 2
  • Kathleen Jun 13, 2018 10:13:
    Tank fills with water and does not go down. I have cleaned venturi, which really was not dirty but cleaned anyway as instructed by phone troublesho​oter.Recha​rged but water still in tank.
  • Troy Jan 23, 2018 10:11:
    What does it mean when it says service fill on model #whes33 le33 and how do you correct it ,water level does not go down in tank
  • Troy Jan 23, 2018 10:11:
    What does it mean when it says service fill on model #whes33 le33 and how do you correct it ,water level does not go down in tank