Download  Print this page

Programming The Water Softener (model Whes20) Customizing Features / Options - Whirlpool WHES33 Installation And Operation Manual

Demand controlled water softener.
Hide thumbs

Advertisement

Table of Contents
Programming the Water Softener
RECHARGE button
When the transformer is plugged into the electrical
outlet, a model code and a test number (example:
J2.0), begin to flash in the faceplate display. Then,
"12:00 PM" and the words "PRESENT TIME" begin to
flash.
NOTE: If "- - - -" shows in the display, press the
s
UP or
DOWN button until the model code
("LE20" for Model WHES20) shows in the dis-
play. Then, press the PROGRAM button to
set, and change to the flashing "PRESENT
TIME" display.
SET TIME OF DAY
If the words "PRESENT TIME" do not show in the dis-
play, press the PROGRAM button until they do.
s
1. Press the
UP or
present time. Up moves the display ahead; down
sets the time back. Be sure AM or PM is correct.
NOTE: Press buttons and quickly release to slowly
advance the display. Hold the buttons down
for fast advance.
Questions? Call Toll Free 1-866-986-3223
When you call, please be prepared to provide the model and serial number,
found on the rating decal, typically located on the rim below the salt lid hinges.
(Model WHES20)
Display
PRESS TO SCHEDULE
HOLD TO START
RECHARGE
DOWN button
DOWN buttons to set the
FIG. 16
or visit www.ecodynewatertreatment.com
UP button
PROGRAM
PROGRAM button
SET WATER HARDNESS NUMBER
1. Press the PROGRAM button once again to display
a flashing "25" and the word "HARDNESS".
2. Press the
UP or
water's hardness number.
NOTE: If your water supply contains iron, compen-
sate for it by adding to the water hardness
number. For example, assume your water is
20 gpg hard and contains 2 ppm iron. Add 5
to the hardness number for each 1 ppm of
iron. In this example, you would use 30 for
your hardness number.
2 ppm iron x 5 = 10 +10
(times)
NOTE: If you use potassium chloride (KCl) salt
instead of sodium chloride (NaCl) salt in this
softener, increase the hardness setting by
25%. For example, if you will be using KCl
and your water supply's hardness is 20 gpg,
set the softener to 25 gpg.
Monday- Friday, 8 AM - 7 PM EST
12
FIG. 15
FIG. 17
s
DOWN buttons to set your
20 gpg hardness
30 HARDNESS NUMBER

Advertisement

Table of Contents

   Also See for Whirlpool WHES33

   Related Manuals for Whirlpool WHES33

This manual is also suitable for:

Whes30Whes20

Comments to this Manuals

Symbols: 0
Latest comments:
  • Caroline Mar 12, 2020 03:21:
    Can I schedule a weekly recharge on the WHES33 or only daily?
  • William greene Apr 09, 2019 03:56:
    How much water should be in bottom of tank man is about 1/4 1/3 full from bottom over slat level that is just at bottom of the nunmber 2
  • Kathleen Jun 13, 2018 10:13:
    Tank fills with water and does not go down. I have cleaned venturi, which really was not dirty but cleaned anyway as instructed by phone troublesho​oter.Recha​rged but water still in tank.
  • Troy Jan 23, 2018 10:11:
    What does it mean when it says service fill on model #whes33 le33 and how do you correct it ,water level does not go down in tank
  • Troy Jan 23, 2018 10:11:
    What does it mean when it says service fill on model #whes33 le33 and how do you correct it ,water level does not go down in tank