Rotary Switch Setting: Info; Exit Button: Sonderfunktion - Daikin EHSX04P30A Operating Instructions Manual

6 x Parameter settings

6.10 Rotary switch setting: Info

Parameter
Overview Display of different current operating data (see section 3.4.1).
Water Pressure The current water pressure is displayed in bar.
T-HS The current temperature (TVBH) of the heat generator is displayed in °C.
T-HS Setpoint The current Inflow target temperature of the heat generator is displayed in °C (see
section 3.6.4).
T-Outside The current external temperature is displayed °C.
T-DHW The current temperature of the hot water storage tank is displayed in °C. If there is no hot water
function activated, "- - -" is displayed.
T-DHW Setpoint The current target hot water temperature is displayed °C. If there is no hot water function acti-
vated, "- - -" is displayed. The current set value is here always the maximum value of all rele-
vant demands for this hot water circuit.
T-Return The current return flow temperature of the heat generator is displayed in °C. If there is no rel-
evant sensor connected to the heat generator, "- - -" is displayed.
Flow Rate The filtered value of the current volume flow in litres per hour is displayed.
T-HC The inflow temperature in the direct heating circuit is displayed in °C.
T-HC Setpoint The set temperature of the flow in the direct heating circuit is displayed in °C.
Status HS pump The current status of the internal heat circulation pump in the Daikin Altherma EHS(X/H) is dis-
played.
Runtime Compres- The running time of the refrigerant compressor is displayed in h.
sor
Runtime Pump The running time of the internal heating circulation pump is displayed in h.
Mixer Position The current position of the 3UV DHW 3-way switch valve is displayed.
0%: Position A (room heating)
100%: Position B (domestic hot water generation)
Qboh The amount of heat in the additional heat generator for hot water generation is displayed in
kWh.
Qchhp The amount of heat in the additional heat generator for heating mode is displayed in kWh.
Qsc The quantity of heat in the heat pump for cooling is displayed in kWh.
Qch The quantity of heat in the heat pump for heating is displayed in kWh.
QWP The total amount of heat in the heat pump is displayed in kWh.
Qdhw The quantity of heat for hot water generation is displayed in kWh.
HS type The heat generator type Daikin Altherma EHS(X/H) detected is displayed.
Sw Nr B1/U1 The software and version of the RoCon B1 operating unit is displayed.
Sw Nr Controller The software number and the version of the RoCon BM1 circuit board are displayed.
Sw Nr RTX RT The software number and the version of the RTX-AL4 circuit board are displayed.
Tab. 6-12 Parameter in rotary switch setting "Info"

6.11 Exit button: Sonderfunktion

Parameter
Manual Operation The direct heating circuit and the target hot water temperature are controlled according to the
temperature set in this parameter (see section 3.5.1).
Display of a current heat pump malfunction in the Daikin Altherma EHS(X/H). 
FA failure
If "----" is displayed there is no fault (see chapter 8).
Protocol Display of protocol (error and information messages). Here we display the saved messages of
the Daikin Altherma EHS(X/H) and the connected data bus units with date a code, in each case
as a menu item. By selecting an entry with the rotary switch, all other corresponding information
is displayed concerning the selected fault message:
- Date and time of the message
- Code number (Information for the heating technician)
- Location (device) where the message originated
- Bus identification (device) where the message originated
Delete message By setting this parameter to "On" and briefly pressing the rotary switch all the entries of the pro-
tocol, including the faults from connected data bus devices, are deleted.
Timeprog Reset Resets all permanent time programmes to factory setting (see tab. 3-8).
Return This parameter is used only to exit the special level.
Tab. 6-13 Parameter in the level "Sonderfunktion"
Operating instructions
38
Description
Description
Access Setting range Factory
Min / Max setting
BE HF
S S - -
S S 0 - 4 bar -
S S 0 - 100 °C -
S S 0 - 90 °C -
S S -39 to +50°C
S S 0 - 100 °C -
S S 10 - 70°C -
S S 0 - 100 °C -
S S 0 - 5100 l/h -
S S 0 - 100 °C -
S S 0 - 90 °C -
S S Off -
On
S S - -
S S - -
S S 0 - 100 % -
S S - -
S S - -
S S - -
S S - -
S S - -
S S - -
S S - -
S S - -
S S - -
S S - -
Access Setting range Factory
Min / Max setting
BE HF
E E 20 - 80 °C 50 °C
E E - -
E E - -
E E Off Off
On
E E Off Off
On
E E
Daikin Altherma EHS(X/H)
Daikin Altherma integrated solar unit
008.1420944 – 05/2014
Incre-
ment
-
0.1 bar
1 °C
0.1 °C
0.1 °C
0.1 °C
0.1 °C
0.1 °C
l/h
0.1 °C
0.1 °C
-
h
h
1 %
kWh
kWh
kWh
kWh
kWh
kWh
-
-
-
-
Incre-
ment
1 °C
-
-
-
-