Makita 3620 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Power Tool
  5. 3620
  6. Instruction manual

Makita 3620 Instruction Manual

Router
Hide thumbs Also See for 3620:

Advertisement

Table of Contents

See also: Instruction Manual
Router
MODEL 3620
I N S T R U C T I O N
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
DOUBLE
INSULATION
M A N U A L
003251

Advertisement

Table of Contents
loading

Related Manuals for Makita 3620

Summary of Contents for Makita 3620

  • Page 1 Router MODEL 3620 003251 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    SPECIFICATIONS Model 3620 Collet capacity 1/4” Plunge capacity 35 mm (1 - 3/8”) No load speed (RPM) 29,000/min. Overall length 211 mm (8 - 5/16”) Net weight 2.4 kg (5.3 lbs) • Manufacturer reserves the right to change specifications without notice.
  • Page 3 5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded.

  • Page 4: Specific Safety Rules

    SERVICE 24. When servicing a tool, use only identical replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury.
  • Page 5 9. Before using the tool on an actual work- 14. Always lead the power supply cord away piece, let it run for a while. Watch for from the tool towards the rear. vibration or wobbling that could indicate 15. Do not smear the tool base carelessly with improperly installed bit.
  • Page 6 SYMBOLS USD201-2 The followings show the symbols used for tool. V ....... volts ....no load speed ˚ A ....... amperes ....Class II Construction Hz ..... hertz .../min....revolutions or reciprocation per minute ....alternating current...

  • Page 7: Functional Description

    FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting the depth of cut 003252 Place the tool on a flat surface. Loosen the screw securing the stopper pole.
  • Page 8 deep with an 8 mm (5/16”) diameter bit or more than 5 mm (3/16”) deep with a 20 mm (13/16”) diameter bit, make several passes with progressively deeper bit settings. Stopper block The stopper block has three adjusting hex bolts which raise or lower 0.8 mm (about 1/32”) per turn.

  • Page 9: Operation

    Switch action 003256 CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. 1.
  • Page 10 001984 1. Workpiece 2. Bit revolving direction 3. View from the top of the tool 4. Feed direction NOTE: • Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor. Moving the tool forward too slowly may burn and mar the cut.
  • Page 11 When cutting, move the tool with the straight guide flush with 003261 the side of the workpiece. If the distance (A) between the side of the workpiece and the cutting position is too wide for the straight guide, or if the side of the workpiece is not straight, the straight guide cannot be used.

  • Page 12: Maintenance

    CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 13 Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold...
  • Page 14 Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Magazine/Newspaper Catalog Tool Distributor Other ( From dealer Other ( Store display 2.
  • Page 15 When you need service... DATE • Explain the problem in a letter PURCHASED: • Enclose the letter with the tool DEALER’S NAME • Package carefully and send prepaid & ADDRESS: to the nearest Makita factory or authorized service centre MODEL NO.: SERIAL NO.:...

  • Page 16: Warranty Policy

    WARRANTY. “The Makita Warranty is the only and the entire written warranty given by Makita for the Makita tools. No dealer or his agent or employee is authorized to extend or enlarge upon this warranty by any verbal or written statement or advertisement.”...

Table of Contents