Download  Print this page

Makita 3620 Instruction Manual

Double insulation router.
Hide thumbs

Advertisement

INSTRUCTION MANUAL
Router
3620
003251
DOUBLE INSULATION
IMPORTANT: Read Before Using.
1

Advertisement

   Related Manuals for Makita 3620

   Summary of Contents for Makita 3620

  • Page 1

    INSTRUCTION MANUAL Router 3620 003251 DOUBLE INSULATION IMPORTANT: Read Before Using.

  • Page 2: Specifications

    EC Declaration of Conformity ENG905-1 Noise Makita Corporation responsible The typical A-weighted noise level determined according manufacturer declare that the following Makita to EN60745: machine(s): Designation of Machine: Sound pressure level (L ) : 89 dB(A) Router Sound power level (L ) : 100 dB(A) Model No./ Type: 3620...

  • Page 3

    Do not abuse the cord. Never use the cord for representative in Europe who is: carrying, pulling or unplugging the power tool. Makita International Europe Ltd. Keep cord away from heat, oil, sharp edges or Michigan Drive, Tongwell, moving parts. Damaged or entangled cords Milton Keynes, Bucks MK15 8JD, England increase the risk of electric shock.

  • Page 4: Save These Instructions

    Power tool use and care Holding the work by hand or against your body 18. Do not force the power tool. Use the correct leaves it unstable and may lead to loss of control. power tool for your application. The correct Wear hearing protection during extended power tool will do the job better and safer at the period of operation.

  • Page 5: Functional Description

    CAUTION: FUNCTIONAL DESCRIPTION Since excessive cutting may cause overload of the • motor or difficulty in controlling the tool, the depth of CAUTION: cut should not be more than 15 mm at a pass when Always be sure that the tool is switched off and •...

  • Page 6

    overtightened bit can be dangerous. Adjusting the lock lever Do not tighten the collet nut without inserting a bit. It • can lead to breakage of the collet cone. 1. Hex nut Insert the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches.

  • Page 7: Straight Guide

    Templet guide (Accessory) 1. Feed direction 2. Bit revolving direction 3. Workpiece 4. Straight guide 001985 Straight guide 003262 The templet guide provides a sleeve through which the bit passes, allowing use of the tool with templet patterns. To install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws.

  • Page 8

    Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding 005073 these accessories, ask your local Makita Service Center. 1. Dust nozzle Straight & groove forming bits • 2. Hose of vacuum Edge forming bits •...

  • Page 9

    "U"Grooving bit Drill point flush trimming bit 005120 005117 006453 "V"Grooving bit 006456 Drill point double flush trimming bit 005118 005121 1/4" 006454 Dovetail bit 006457 Slotting cutter 005119 005122 14.5 15SE 3/8" 14.5 14.5 15LE 3/8" 1/2" 3/8" 1/2" 006455 006458...

  • Page 10

    Board-jointing bit Chamfering bit 005123 005127 1/2" 006461 005124 006459 005126 Corner rounding bit 006462 Beading bit 005125 006460 005128 1/2" 006463...

  • Page 11

    Cove beading bit Ball bearing chamfering bit 005132 005129 1/4" 006464 006467 Ball bearing beading bit Ball bearing flush trimming bit 005133 005130 1/4" 006465 006468 Ball bearing corner rounding bit Ball bearing cove beading bit 005131 005134 1/4" 006466 006469...

  • Page 12

    Ball bearing roman ogee bit 005135 006470 Double ball bearing round corner bit 005136 1/2" 006471...

  • Page 16

    Makita Corporation Anjo, Aichi, Japan www.makita.com 883585F225...

Comments to this Manuals

Symbols: 0
Latest comments: