Table of Contents
Advertisement
UX-A1000U
SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (High)
The transmission level of DTMF signal is adjusted. (higher frequency)
00000: 0dBm
↓
11111: -15.5 dBm (-0.5dBm x 31)
SW-B6 No. 6 ~ No. 8 Reserved
Set to "0".
SW-C1 No. 1, No. 2 Reading slice (Binary)
Used to determine the set value of reading density in standard/fine mode.
The standard setting is "00" (Factory setting is "00")
SW-C1 No. 3, No. 4 Reading slice (Half tone)
Used to determine the set value of reading density in half tone mode.
The standard setting is "00" (Factory setting is "00")
SW-C1 No. 5 Line density selection
Used to set the transmission mode which is automatically selected when
the Resolution key is not pressed. In the copy mode, however, the fine
mode is automatically selected unless the Resolution key is manually
set to another mode.
SW-C1 No. 6 Reserved
Set to "0".
SW-C1 No. 7 MTF correction in half tone mode
This allows selection of MTF correction (dimness correction) in the half
tone mode.
When "NO" (=1) is selected, the whole image becomes soft and mild.
Clearness of characters will be reduced. Normally set to "YES" (=0).
SW-C1 No. 8 Reserved
Set to "0".
SW-D1 No. 1 ~ No. 4 Number of rings for auto receive
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to four rings
using a binary number. Since the facsimile telephone could be used as
an ordinary telephone if the handset is taken off the hook, it should be
programmed to the user's choice. If the soft switch was set to 1, direct
connection is made to the facsimile. If a facsimile calling beep was heard
when the handset is taken off the hook, press the START key and put
the handset on the hook to have the facsimile start receiving. If it was
set to 0 accidentally, receive ring is set to 1.
NOTE: If the machine is set to answer after a large number of rings, it
may not be able to receive faxes successfully. If you have diffi-
culty receiving faxes, reduce the number of rings to a maximum
of 6.
SW-D1 No. 5 Automatic switching manual to auto receive mode
This soft switch is used to select whether the machine should switch to
the auto receive mode after 5 rings in the manual receive mode or re-
main in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4 "0"1"0"0"(5
rings).
SW-D1 No. 6 Reserved
Set to "0".
SW-D1 No. 7, No. 8 CI detect frequency
Detection frequency of ring signal for auto reception is set.
When set to No. 7=0, No. 8=0, frequency is set to PTT recommenda-
tion.
When set to No. 7=0, No. 8=1, frequency is set to 11.5Hz or more.
When set to No. 7=1, No. 8=0, frequency is set to 13.0Hz or more.
When set to No. 7=1, No. 8=1, frequency is set to 20.0Hz or more.
SW-D2 No. 1 ~ No. 3 Distinctive ringing setting (PATTERN 4 and 5
are for CANADA only)
This function allows reception of services offered by USA and Canada
telephone companies in which the customer contracts with the telephone
company to have up to 4 telephone numbers (USA) or 6 telephone num-
bers (Canada) established for one line.
Each telephone number is signalled by a different ringing pattern, and
the customer can allocate each number to a specific use.
<Example of use>
Phone Number
Ring Pattern
555-1234
555-1235
555-1236
555-1237
<Distinctive Ringing Timing Specifications>
1) USA
DISTINCTIVE RING → 1:RING PATTERN 1 → 2:RING PATTERN 2
↑
← 4:STANDARD RING ← 3:RING PATTERN 3
5:OFF SETTING
2) Canada
DISTINCTIVE RING → 1:RING PATTERN 1 → 2:RING PATTERN 2
↑
7:OFF SETTING
↑
6:STANDARD RING ← 5:RING PATTERN 5 ← 4:RING PATTERN 4
•
Ring Pattern
STANDARD has 5 ring patterns, and DISTINCTIVE has 9 patterns.
Ring patterns
~
1
4
However, to make the setting procedure as easy as possible for the
user to understand these patterns are grouped as follows:
<
Optional Setting>
1) RING PATTERN 1
2) RING PATTERN 2
3) RING PATTERN 3
4) RING PATTERN 4
5) RING PATTERN 5
6) STANDARD RING
7) OFF SETTING
STANDARD
1.5S ring
1S ring
1.5S ring
0.8S
RING
PATTERN 1
for USA
0.3S
RING
PATTERN 2
for USA
0.2S
0.4S
RING
PATTERN 3
for USA
0.2S 0.2S
RING
PATTERN 4
for USA
RING
PATTERN 5
for CANADA
RING
PATTERN 6
for CANADA
RING
PATTERN 7
for CANADA
0.25S 0.25S 0.25S
RING
PATTERN 8
for CANADA
0.25S 0.25S
RING
PATTERN 9
for CANADA
2 – 20
2 – 20
Intended
Ring Pattern
Purpose
Voice Calls
Facsimile Calls
Answering
Machine
PC Modem
3:RING PATTERN 3
for USA, and
~
for Canada.
5
9
RING PATTERN
1
RING PATTERN
4
RING PATTERN
5
RING PATTERN
2
RING PATTERN
6
RING PATTERN
3
RING PATTERN
7
RING PATTERN
8
RING PATTERN
9
2S ring
4S ring
2S ring
2S ring
3S ring
4S ring
0.5S
0.5S
4S ring
0.8S
0.4S
4S ring
1S
0.3S
0.2S
4S ring
0.4S 0.8S
4S ring
1S
1S
4S ring
1S
1S
1S
0.5S
0.5S
1S
0.5S
0.5S
0.5S
1S
0.5S
0.5S
0.5S
0.5S
0.2S
0.2S
0.2S
6S
Standard
Pattern 1
Pattern 2
Pattern 3
↓
↓
↓
for USA
for USA
for Canada
for USA
for Canada
for USA
for Canada
for Canada
for Canada
Advertisement
Table of Contents
