Lutron Electronics Pico QSR4P-3R Installation Instructions

Pico wireless
English
®
control
Pico wireless control
®
QSR4P-3R, QSR8P-3R, QSRKP-3R,
QSRMP-3R, QSRKP-2R, QSRMP-2R,
Installation Instructions
QSRKP-2, QSRMP-2
Please Read Before Installing
3 V 10 mA
LUTRON
LUTRON
QSR4P-3R QSRKP-2R QSRKP-2
QSR8P-3R
QSRMP-2R QSRMP-2
QSRKP-3R
QSRMP-3R
Overview
Pico wireless controls are for use with Lutron RF systems. The controls are
®
programmed by the installer as shown in these instructions or the system
Setup Guide.
Important Notes
Codes: Install in accordance with all local and national electrical codes.
Environment: Ambient operating temperature: 32 °F to 140 °F
(0 °C to 60 °C), 0 to 90% humidity, non-condensing. Indoor use only.
Wallplates: Use only Lutron wallplates with this device. The mechanical
design of the Pico wireless control is NOT compatible with non-Lutron
wallplates. Claro and Satin Colors wallplates are strongly recommended
® ®
for best color match and clean aesthetic appearance. Do not paint
controls, buttons, or wallplates. Wallplates are sold separately.
Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any
chemical cleaning solutions.
Battery: The Pico wireless control uses one (1) CR 2032 battery (included).
Keep battery out of reach of children. DO NOT use rechargeable batteries.
Using improper batteries could damage the Pico wireless control. DO NOT
dispose of the battery in normal household waste. Please recycle battery,
take to a battery disposal facility, or contact your local waste disposal
provider regarding local restrictions on the disposal or recycling of batteries.
For California residents only: The batteries in these devices contain
perchlorate material - special handling may apply. For more information
visit: www.dtsc.ca.gov/hazardouswaste/perchlorate
RF Device Placement: RF dimmers, switches, keypads, controls and
shades/draperies must be located within 30 ft (9 m) of an RF signal
repeater. For systems without an RF signal repeater, all RF dimmers,
switches, keypads, controls and shades/draperies must be located within
30 ft (9 m) of each other. Remote dimmers and switches hardwired to RF
dimmers and switches are not required to be within a specific range.
Mounting: For optimal performance, DO NOT mount the Pico Wireless
control to a metal surface.
Contents:
(1) Pico wireless control
(1) Blank (1) Wall mount plate
backplate
LUTRON
(4) Mounting screws (4) Screw anchors (1) Wall mount template
Technical Assistance:
U.S.A. / Canada: 1.800.523.9466 Other Countries: +1.610.282.3800
Mexico: +1.888.235.2910 24 hours a day, 7 days a week.
Lutron Elec tron ics Co., Inc.
7200 Suter Road Coopersburg, PA 18036-1299
Made and print ed in the U.S.A. 06/10 P/N 045-304 Rev. B
1 Pico Wireless Control Operation
The Pico wireless control can be used as a handheld remote, wall mount
control or tabletop control. The Pico can simply be converted to a wall
mount control by removing the back plate and attaching the control to
the wall mount adapter plate that has been mounted to the wall. The Pico
wireless control can also be converted to a tabletop control by attaching it
to the optional tabletop pedestal.
Tap Top Button Press Raise Button:
(–3R & –2R only)
Shades Or Draperies:
Go to Open limit
Shades Or Draperies:
(–3R & –2R only)
Move towards open limit
Grafik Eye QS Wireless
® Grafik Eye QS Wireless
In Scene Control Mode:
In Scene Control Mode:
Activates Scene 1
Brightens all zones
(–3R & –2R & –2)
Grafik Eye QS Wireless
Grafik Eye QS Wireless
In Zone Control Mode:
In Zone Control Mode:
Brightens all assigned zones
All assigned Zones
brighten to 100%
All other dimming devices:
(–3R & –2R & –2)
Brighten light level
All other lighting devices:
Switching devices:
Brighten to 100%
Turn on
(–3R & –2R & –2)
Press Lower Button:
Tap Round Button:
(–3R & –2R only)
(–3R only)
Shades Or Draperies:
Shades Or Draperies:
Moves towards close limit
Go to favorite preset
Grafik Eye QS Wireless
Grafik Eye QS Wireless
In Scene Control Mode:
In Scene Control Mode:
Dims all zones
Activates Scene 16
Grafik Eye QS Wireless
Grafik Eye QS Wireless
In Zone Control Mode:
In Zone Control Mode:
Dims all assigned zones
All assigned Zones
go to the preset level
All other dimming devices:
Brighten light level
All other lighting devices:
Go to favorite preset
Switching devices:
No function available
Tap Bottom Button:
Shades Or Draperies:
Move to Close limit
(–3R & –2R only)
Grafik Eye QS Wireless
In Scene Control Mode:
Fade to off
(–3R & –2R & –2)
Grafik Eye QS Wireless
In Zone Control Mode:
Fade to off
(–3R & –2R & –2)
All other lighting devices:
Fade to off
(–3R & –2R & –2)
Lutron, Claro, Satin Colors, GRAFIK Eye, Pico and the sunburst logo are registered trademarks and FASS is a trademark of Lutron Electronics Co., Inc.
©2010 Lutron Electronics Co., Inc.
2 Installation
The Pico wireless control can be used as a handheld remote, table top
control or wall mount control. See the corresponding section below
based on the type of installation desired.
Handheld remote: Slide the Blank Backplate into the back of the Pico
wireless control.
Tabletop control: Slide the Pico wireless control onto the Tabletop
Pedestal (sold separately). Pedestal model numbers are:
QSA-PED1 (holds 1 Pico control) and QSA-PED2 (holds 2 Pico controls).
L-PED1
Wall mount control: See the Wall Mount Template sheet included with
the Pico wireless control for various wall mount applications.
Battery Replacement
3
WARNING: Burn hazard. To avoid the risk of fire, explosion
or burns, DO NOT recharge, disassemble, crush, puncture
or incinerate the battery. DO NOT heat the battery above
212 °F (100 °C).
1. Remove the battery holder screw and slide the battery holder out of
the back of the Pico wireless control.
Battery Holder
Screw
2. Remove existing battery and replace with a new CR 2032 battery,
positive (+) side down. Slide battery holder back into the Pico wireless
control until it snaps into place and insert the battery holder screw.
Do not overtighten screw.
Battery Holder
Screw
4 Simple Setup
To program a system which contains a Main Repeater refer to the system
Setup Guide. Follow the instructions below to program a system which does
NOT contain a Main Repeater.
After all devices have been installed, the Pico wireless control must be
programmed to control a set of dimmers, switches and shades/draperies.
Programming a system which does NOT contain a Main Repeater consists of
two steps:
1. Assigning dimmers, switches, keypads and shades/draperies to a Pico
wireless control
2. Saving the desired light levels and shade/drapery positions
Assigning devices to a Pico wireless control
1. Enter assign mode – press and hold the top and bottom buttons of
the Pico wireless control until the LED begins to flash (approximately 6
seconds).
Note: The Pico control will automatically exit assign mode after 10 minutes.
2. Assign devices to the Pico wireless control
a. Dimmers/switches – press and hold the tapswitch on the device until the
load flashes 3 times (approximately 6 seconds). The LEDs on assigned
dimmers and switches will continue to flash while the Pico control is in
assign mode.
b. Shades/draperies – press any button on the drive and the LED will flash.
3. Assign keypad columns – press and hold the bottom button of the
keypad column to be assigned until the LEDs begin to flash (approximately
6 seconds).
4. When all devices have been assigned, exit assign mode by holding the top
and bottom buttons of the Pico wireless control until the LED stops flashing
L-PED2
(approximately 3 seconds).
5. Confirm programming by individually pressing every button on the Pico
wireless control. Assigned devices respond to the button press by going to
the default level for that button. During normal operation, when a button is
pressed, the LED next to the top button will flash for 1-2 seconds and turn
off to conserve battery power.
Saving light levels and shade/drapery positions
You can customize the levels or positions of the devices assigned to a Pico
wireless control by using the steps below. The Pico control containing the
button to be customized must have already been programmed according to
Assigning devices to a Pico wireless control, above.
1. Press the button you wish to customize. The lights and shades/draperies
will move to the default level(s) and/or position(s) for this button. Wait until
the lights and shades/draperies stop dimming and moving.
2. Adjust each dimmer, switch and shade/drapery assigned to that column
as follows:
a. Dimmers - use the tapswitch to toggle the lights on or off. Use the raise
or lower button on the right side of the dimmer to make adjustments to
the desired light levels.
b. Switches - use the tapswitch to toggle the lights on or off.
c. Shades/draperies - use the clockwise or counter-clockwise buttons on
the shade/drapery to adjust the position.
3. Making dimmers, switches and shades/draperies 'unaffected'
(optional) – to make assigned devices not respond to a button press, you
may make the devices 'unaffected'. During normal operation when you
press a button on a control, a device that is 'unaffected' will ignore that
button press. The light level or shade/drapery position will not change. To
make devices 'unaffected', follow the corresponding step below based on
the type of device to be made 'unaffected'.
a. Dimmer – if the dimmer is on, turn it off using the tapswitch. After the
dimmer is completely off, hold the lower rocker until the three middle
LEDs turn on (approximately 6 seconds), signifying that the next save will
be ignored. **
b. Switch – if the switch is on, turn it off using the tapswitch. Pull the
FASS switch out. Press and hold the tapswitch. While still holding the
™
tapswitch, push the FASS switch in. Continue holding the tapswitch until
the LED flashes, signifying that the next save will be ignored. **
c. Shade/Drapery – if the shade/drapery is open, close it using either the
clockwise or counter-clockwise button. Release the button. After the
shade/drapery is closed, press and hold the same button used to close
the shade/drapery until the green LED blinks (approximately 10 seconds),
signifying that the next save will be ignored. **
4. Press and hold the selected Pico wireless control button until the
LED flashes (approximately 6 seconds) to save the current levels or the
'unaffected' status. The LED will blink rapidly for 1-2 seconds to confirm
that the save was successful.
** After a device becomes 'unaffected', you have 10 minutes to complete the
save for all dimmers, switches and shades/draperies.
Note: To change the 'unaffected' status of a dimmer, switch or shade/
drapery, follow the steps in Saving light levels and shade/drapery
positions above.