Advertisement
Assigning a GRAFIK Eye
Wireless Unit to the
5
®
Pico Wireless Control
5.1
Scene Control
Set the wireless mode on the GRAFIK Eye unit
5.1.1
to "Setup Mode". Refer to the instructions that
came with the GRAFIK Eye unit.
Place the Pico
wireless control into
5.1.2
®
Programming Mode by pressing and holding the
Top button and Bottom button for 3 seconds.
The GRAFIK Eye unit should display a screen
5.1.3
saying: "Pico: change type?"
Press OK on the GRAFIK Eye unit, select the
5.1.4
"Scene" type, then press OK.
5.1.5
Now hold the Top Scene button on the GRAFIK
Eye unit for 3 seconds. The scene LEDs should
start flashing and all zones should go to
maximum intensity.
Exit Programming Mode on the Pico wireless
5.1.6
control by pressing and Top button and Bottom
button for 3 seconds.
5.2
Zone Control
Set the wireless mode on the GRAFIK Eye unit
5.2.1
to "Setup Mode". Refer to the instructions that
came with the GRAFIK Eye unit.
5.2.2
Place the Pico wireless control into Programming
Mode by pressing and holding the Top button
and Bottom button for 3 seconds.
The GRAFIK Eye unit should display a screen
5.2.3
saying: "Pico: change type?"
5.2.4
Press OK on the GRAFIK Eye unit, select the
"Zone" type, then press OK
Set a zone to a desired preset level, using the
5.2.5
Raise and Lower buttons on the GRAFIK Eye
unit. Then press and hold both the Raise and
Lower button until the Zone LEDs begin to flash.
Repeat step 5.2.5 for each zone that will be
5.2.6
controlled by the Pico wireless control.
Exit Programming Mode on the Pico wireless
5.2.7
control by pressing and holding the Top button
and Bottom button for 3 seconds.
Lutron Elec tron ics Co., Inc.
7200 Suter Road Coopersburg, PA 18036-1299
Made and print ed in the U.S.A. 06/10 P/N 045-304 Rev. B
Storing a Favorite Preset (not applicable to
6
GRAFIK Eye QS)
The round button on the Pico wireless control allows the user to
recall a favorite preset of all the devices assigned to that control.
6.1
Position the shade(s), drapery(ies) or light level
to the desired setting using the Raise or
Lower button on the Pico wireless control.
6.2
Press and hold the round button on the
Pico wireless control for 5 seconds. The
green LED on the control will flash rapidly
for 5 seconds, turn off for 5 seconds, flash
rapidly and turn off indicating the preset has
been stored.
Troubleshooting Guide (for simple setup)
Symptom
Probable Cause and Action
LED on a Pico wireless
Pico
Dead, low, or no battery in
wireless control.
• Install new battery.
control doesn't light up
when buttons on it are
Battery is installed incorrectly (reversed polarity).
pressed.
• Install battery as indicated in the Battery
Replacement section.
A specific dimmer, switch
The dimmer, switch or shade/drapery is not assigned to
or shade/drapery not
the Pico control.
controlled when a button
• Follow the steps in Assigning devices to a
is pressed on a Pico
wireless control.
wireless control.
The device is 'unaffected' for that button.
• Follow the steps in Saving light levels and shade/
drapery positions to change the 'unaffected' status
of the device.
The lamp(s) controlled by the dimmer/switch is (are)
burned out.
• Replace the lamp(s).
Either there is no power to the device or the FASS
switch is pulled out on a dimmer/switch.
• Ensure that the device is powered and push the
FASS switch in.
Devices are out of range.
• Check to make sure all Pico controls, keypads,
dimmers, switches and shades/draperies are within
30 ft (9 m) of each other.
Dimmer, switch or shade/
The button was not programmed correctly.
drapery does not go
• Follow the steps in Saving light levels and
to the desired level or
shade/drapery positions to program the button.
position when a button
The device is 'unaffected' for that button.
on the Pico wireless
• Follow the steps in Saving light levels and
control is pressed.
shade/drapery positions to change the 'unaffected'
status of the device.
The button pressed is the bottom button.
• The bottom button cannot be saved or modified.
Devices are out of range.
• Check to make sure all Pico controls, keypads,
dimmers, switches and shades/draperies are within
30 ft (9 m) of each other.
Note: Refer to the system Setup Guide for additional troubleshooting suggestions.
Lutron, Claro, Satin Colors, GRAFIK Eye, Pico, the sunburst logo are registered trademarks and FASS is a trademarks of Lutron Electronics Co., Inc.
©2010 Lutron Electronics Co., Inc.
Returning Pico wireless controls to Factory Settings
Note: Returning a Pico wireless control to its Factory Settings will remove
it from the system and erase all programming.
Step 1: Triple tap and hold either the Top or Bottom button on a Pico wireless control.
DO NOT release the button after the third tap.
Step 2: Keep the button pressed on the third tap until the LED next to the top button
turns on solid (approximately 3 seconds).
Step 3: Immediately release the button and triple tap it again. The LED next to the top
button will flash quickly. When the LED stops flashing, the control has been
returned to Factory Settings.
FCC Information
(For model number QSR4P-3R)
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio and television reception, which can
be determined by turning the equipment off and on. The user is encouraged to try to correct
the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Note:
Changes or modifications not expressly approved by Lutron
Electronics Co. could void the user's authority to operate this equipment.
* This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
Pico
(2) This device must accept any interference received, including interference
that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
CE Information
(For model numbers QSR8P-3R, QSRKP-3R,
QSRMP-3R, QSRKP-2R, QSRMP-2R, QSRKP-2 and QSRMP-2)
Lutron Electronics hereby declares that the model numbers listed above are in
compliance with the essential requirements and other relevant provisions of
™
Directive 1999/5/EC. A copy of the DoC can be obtained by writing to:
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036 U.S.A.
IDA Compliance Information
(For model numbers QSRMP-3R,
QSRMP-2R and QSRMP-2)
Complies with
IDA standards
DA 103083
TRA Compliance Information
(For model numbers QSR8P-3R,
QSRKP-3R, QSRKP-2R and QSRKP-2)
TRA
REGISTERED
NO:
ER0037292/10
DEALER NO:
0016561/08
Warranty
Lutron Electronics Co., Inc.
TO MAKE A WARRANTY CLAIM
One Year Limited Warranty
To make a warranty claim, promptly notify Lutron within the
For a period of one year from the date of purchase, and sub-
warranty period described above by calling the Lutron Techni-
ject to the exclusions and restrictions described below, Lutron
cal Support Center at (800) 523-9466. Lutron, in its sole dis-
warrants each new unit to be free from manufacturing defects.
cretion, will determine what action, if any, is required under this
Lutron will, at its option, either repair the defective unit or issue
warranty. To better enable Lutron to address a warranty claim,
a credit equal to the purchase price of the defective unit to the
have the unit's serial and model numbers available when mak-
Customer against the purchase price of comparable replace-
ing the call. If Lutron, in its sole discretion, determines that an
ment part purchased from Lutron. Replacements for the unit
on-site visit or other remedial action is necessary, Lutron may
provided by Lutron or, at its sole discretion, an approved
send a Lutron Services Co. representative or coordinate the
vendor may be new, used, repaired, reconditioned, and/or
dispatch of a representative from a Lutron approved vendor to
made by a different manufacturer.
Customer's site, and/or coordinate a warranty service call
If the unit is commissioned by Lutron or a Lutron approved
between Customer and a Lutron approved vendor.
third party as part of a Lutron commissioned lighting control
This warranty gives you specific legal rights, and you may
system, the term of this warranty will be extended, and any
also have other rights which vary from state to state. Some
credits against the cost of replacement parts will be prorated,
states do not allow limitations on how long an implied warranty
in accordance with the warranty issued with the commissioned
lasts, so the above limitation may not apply to you. Some
system, except that the term of the unit's warranty term will be
states do not allow the exclusion or limitation of incidental or
measured from the date of its commissioning.
consequential damages, so the above limitation or exclusion
may not apply to you.
EXCLUSIONS AND RESTRICTIONS
This Warranty does not cover, and Lutron and its suppliers are
© 2010 Lutron Electronics Co., Inc.
not responsible for:
1. Damage, malfunction or inoperability diagnosed by Lutron or
Contact Information
a Lutron approved third party as caused by normal wear and
Internet: www.lutron.com
tear, abuse, misuse, incorrect installation, neglect, accident,
E-mail: product@lutron.com
interference or environmental factors, such as (a) use of
incorrect line voltages, fuses or circuit breakers; (b) failure to
WORLD HEADQUARTERS
install, maintain and operate the unit pursuant to the operating
USA
instructions provided by Lutron and the applicable provisions
Lutron Electronics Co., Inc.
of the National Electrical Code and of the Safety Standards of
7200 Suter Road, Coopersburg, PA
Underwriter's Laboratories; (c) use of incompatible devices or
18036-1299
accessories; (d) improper or insufficient ventilation; (e)
TEL +1.610.282.3800
unauthorized repairs or adjustments; (f) vandalism; or (g) an act
FAX +1.610.282.1243
of God, such as fire, lightning, flooding, tornado, earthquake,
Toll-Free 1.888.LUTRON1
hurricane or other problems beyond Lutron's control.
Technical Support 1.800.523.9466
2. On-site labor costs to diagnose issues with, and to remove,
North and South America
repair, replace, adjust, reinstall and/or reprogram the unit or
Technical Hotlines
any of its components.
USA, Canada, Caribbean: 1.800.523.9466
3.Equipment and parts external to the unit, including those
Mexico: +1.888.235.2910
sold or supplied by Lutron (which may be covered by a
Central/South America: +1.610.282.6701
separate warranty).
4. The cost of repairing or replacing other property that is dam-
EUROPEAN HEADQUARTERS
aged when the unit does not work properly, even if the damage
United Kingdom
was caused by the unit.
Lutron EA Ltd.
6 Sovereign Close, London,
EXCEPT AS EXPRESSLY PROVIDED IN THIS WAR-
E1W 3JF United Kingdom
RANTY, THERE ARE NO EXPRESS OR IMPLIED
TEL +44.(0)20.7702.0657
WARRANTIES OF ANY TYPE, INCLUDING ANY IMPLIED
FAX +44.(0)20.7480.6899
WARRANTIES OF FITNESS FOR A PARTICULAR
FREEPHONE (UK) 0800.282.107
PURPOSE OR MERCHANTABILITY. LUTRON DOES NOT
Technical support +44.(0)20.7680.4481
WARRANT THAT THE UNIT WILL OPERATE WITHOUT
INTERRUPTION OR BE ERROR FREE.
ASIAN HEADQUARTERS
NO LUTRON AGENT, EMPLOYEE OR REPRESENTA-
Singapore
TIVE HAS ANY AUTHORITY TO BIND LUTRON TO ANY
Lutron GL Ltd.
AFFIRMATION, REPRESENTATION OR WARRANTY
15 Hoe Chiang Road,
CONCERNING THE UNIT. UNLESS AN AFFIRMA-
#07-03 Euro Asia Centre, Singapore 089316
TION, REPRESENTATION OR WARRANTY MADE BY
TEL +65.6220.4666
AN AGENT, EMPLOYEE OR REPRESENTATIVE IS
FAX +65.6220.4333
SPECIFICALLY INCLUDED HEREIN, OR IN STANDARD
Asia Technical Hotlines
PRINTED MATERIALS PROVIDED BY LUTRON, IT DOES
Northern China: 10.800.712.1536
NOT FORM A PART OF THE BASIS OF ANY BARGAIN
Southern China: 10.800.120.1536
BETWEEN LUTRON AND CUSTOMER AND WILL
Hong Kong: 800.901.849
NOT IN ANY WAY BE ENFORCEABLE BY CUSTOMER.
Indonesia: 001.803.011.3994
IN NO EVENT WILL LUTRON OR ANY OTHER PARTY
Japan: +81.3.5575.8411
BE LIABLE FOR EXEMPLARY, CONSEQUENTIAL,
Macau: 0800.401
INCIDENTAL OR SPECIAL DAMAGES (INCLUDING, BUT
Singapore: 800.120.4491
NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS,
Taiwan: 00.801.137.737
CONFIDENTIAL OR OTHER INFORMATION, OR PRI-
Thailand: 001.800.120.665853
VACY; BUSINESS INTERRUPTION; PERSONAL INJURY;
Other countries: +65.6220.4666
FAILURE TO MEET ANY DUTY, INCLUDING OF GOOD
FAITH OR OF REASONABLE CARE; NEGLIGENCE, OR
ANY OTHER PECUNIARY OR OTHER LOSS WHATSO-
EVER), NOR FOR ANY REPAIR WORK UNDERTAKEN
WITHOUT LUTRON'S WRITTEN CONSENT ARISING OUT
OF OR IN ANY WAY RELATED TO THE INSTALLATION,
DEINSTALLATION, USE OF OR INABILITY TO USE THE
UNIT OR OTHERWISE UNDER OR IN CONNECTION
WITH ANY PROVISION OF THIS WARRANTY, OR ANY
AGREEMENT INCORPORATING THIS WARRANTY, EVEN
IN THE EVENT OF THE FAULT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY, BREACH OF CON-
TRACT OR BREACH OF WARRANTY OF LUTRON OR
ANY SUPPLIER, AND EVEN IF LUTRON OR ANY OTHER
PARTY WAS ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
NOTWITHSTANDING ANY DAMAGES THAT CUSTOMER
MIGHT INCUR FOR ANY REASON WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, ALL DIRECT
DAMAGES AND ALL DAMAGES LISTED ABOVE), THE
ENTIRE LIABILITY OF LUTRON AND OF ALL OTHER
PARTIES UNDER THIS WARRANTY ON ANY CLAIM FOR
DAMAGES ARISING OUT OF OR IN CONNECTION WITH
THE MANUFACTURE, SALE, INSTALLATION, DELIVERY,
USE, REPAIR, OR REPLACEMENT OF THE UNIT, OR
ANY AGREEMENT INCORPORATING THIS WAR-
RANTY, AND CUSTOMER'S SOLE REMEDY FOR THE
FOREGOING,WILL BE LIMITED TO THE AMOUNT PAID
TO LUTRON BY CUSTOMER FOR THE UNIT. THE FORE-
GOING LIMITATIONS, EXCLUSIONS AND DISCLAIMERS
WILL APPLY TO THE MAXIMUM EXTENT ALLOWED BY
APPLICABLE LAW, EVEN IF ANY REMEDY FAILS ITS
ESSENTIAL PURPOSE.
Advertisement
