Canceling A Cycle; Changing A Cycle Or Setting; Adding Items During A Cycle; Option Selections - Kenmore 665.15732 Use And Care Manual

Use this rinse cycle for Do not use
rinsing dishes, glasses, detergent
and silverware that will with this
not be washed right away. cycle,
Soil Wash Rinse Main Rinse Final Dry Time Water
Level Wash Heated (rain) Usage
Sensed Rinse (gal/L)
• • 14 4.3/16,4
Heavy
• 10 2.2/8.2
Ught
NOTE: The sensor in your dishwasher monitors the soil level.
Cycle time and/or water usage can vary from the numbers above
as the sensor adjusts the cycle for the best wash performance.
Canceling a Cycle
Anytime during a cycle, press
Adding Items During a Cycle
You can add an item anytime before the main wash starts. Open
the door end check the detergent dispenser. If the main wash
section is still closed, you can add items.
To add items
1. Lift up the door latch to stop the cycle. Wait for the spraying
action to stop before opening the door.
2, Open the door. If the main wash detergent dispenser is still
closed, add the item.
3, Close the door, but do not latch it. Wait 30 eeconds for the air
in the dishwasher to warm up. This reduces the amount of
moisture escaping from the vent when restarting a cycle.
4. Close the door firmly until it latches. The dishwasher resumes
the cycle after about a 5 second pause.
Option Selections
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
O any time before drying begins.
Press START to use the same cycle and option(s) as the previous
wash cycle,
NOTE; If the last cycle you completed was a rinse cycle, when
CANCEL/DRAIN glows. The dishwasher pauses for about 5 you press Start, the dishwasher runs the last full wash cycle and m
seconds and starts a 2 minute drain (if needed). Let the options. |
dishwasher drain completely. The light goes off when the
dishwasher finishes the drain.
To stop the drain
You can press CANCEL/DRAIN again to stop the drain
immediately. Remember to drain the dishwasher before starting a
new cycle.
NOTE: A small amount of water remains in the dishwasher. This
is normal.
To clear the indicators
Press CANCEL!DRAIN before starting the dishwasher to clear all
options and cycles.
Hi Temp Scrub
Select this option to heat the water during parts of the cycle. Hi
Temp Scrub heats the water to 145°F (63°C) in the main wash.
Heating the water helps improve washing results.
This option adds heat, water and wash time to the cycle.
NOTE: Hi Temp Scrub is an option with Pots Pans and Normal
Wash.
Changing a Cycle or Setting
During the first minute of a cycle
Press a new cycle and/or options.
After the first minute of a cycle
1. Press
CANCEL/DRAIN glows. The dishwasher pauses for 5
seconds and starts a 2 minute drain (if needed). Let the
dishwasher drain completely.
2. Check the detergent dispensers. If the main wash cup has
opened and the detergent washed away, refill the cups as
needed.
3. Close the door.
4. Press a new cycle and/or options.
5. Press START
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C) for 10 minutes. Sani Rinse adds
heat and time to the cycle. In the Normal cycle this high-
temperature rinse sanitizes your dishes and g[aasware in
accordance with the NSF Protocol P153 Sanitization and
CJeaning Performance of Household Spray-Type Dishwashers,
NOTE; Sani Rinse is an option with Pats Pans, Normal Wash and
Water Miser.
13