Regulatory Information; Environmental Considerations; Product Specification; Fcc Declaration Of Conformity - Bosch Power Xpress Installation And Operating Instructions Manual

Regulatory Information

Environmental Considerations

At the end of service life, the Charge Station
should be recycled according to local laws and
regulations.

Product Specification

All Charge Station specifications and descriptions are
accurate at the time of this document's printing. We
always strive to constantly improve and update our
products, Bosch reserves the right to make changes at
any time, without notice and without obligation.

FCC Declaration of Conformity

This device complies with Part 15 Class-B of the
FCC rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful inter-
ference, and 2) this device must accept any interference
received, including interference that may cause unde-
sired operation.
Note:
Non-authorized changes or modifications to this prod-
uct could void its FCC compliance.

Radio and Television Interference

The equipment described in this manual has been
designed to protect against Radio Frequency Inter-
ference (RFI). However, there are some instances where
high-powered radio signals or nearby RF-producing
equipment (such as digital phones, RF communications
equipment, etc.) could affect Charge Station opera-
tions. If interference to the Charge Station occurs dur-
ing charging, contact Bosch.

Agency Approvals

Standard Compliances through a National Registered
Testing Lab (NRTL)
North American Operation
FCC Part 15 Class-B
UL 2594
UL 2251
UL 62
UL 60950-1
UL 1998
UL 2231-1 & -2
CSA C22.2 #60950-1
CSA C22.2 #107.1
SAE J1772
NEC Article 625
European Union Operation
IEC 61851-1
IEC 61851-21 & -22
IEC 60950-1
IEC 61000-6-1 EMC Immunity
IEC 61000-6-3 EMC Emissions
IEC 62196 Coupler, Type 1, Type 2
IEC 60204-1, Safety for servicing electronic equipment
Bosch Automotive Service Solutions LLC
Installation and Operating Instructions | Power Xpress Charge Station | 3 | en

Features and Specifications

The Charge Station includes ground-fault protection,
automatic reset upon grid power loss, ground assurance
monitoring, and self-testing capabilities. Manual reset-
ting of the Charge Station is not necessary. Exception:
European models require manual resetting after ground
fault condition.

Ground-fault protection

Continually provides a safe power supply to the vehicle.
If a ground fault is present, the Charge Station detects it
and cuts power flow, protecting people and the vehicle
from an electric shock hazard.

Automatic reset

If main line side power supply is interrupted during
charging, the Charge Station will reset itself automati-
cally and re-attempt charging after main line side power
supply is restored.
If the problem is associated with a ground fault, the
Charge Station makes a total of 4 automatic reset at-
tempts in sequential 15-minute periods. If the charging
mode can not be restored, the appropriate failure indica-
tion will be shown on the unit's front panel. NOTE: Not
applicable on European models; European models re-
quire pressing of the master clear "Reset" button on the
front panel of the Charge Station to restore power.
See Table-A in Operating Instructions for LED status indi-
cations (page 11).
The automatic reset feature assures that your vehicle will
be charged and ready to use by automatically restoring
power after temporary interruptions (grid-power out-
ages, temporary ground faults [US models only] and
power surges).

Ground Assurance Monitoring

A proper electrical ground is critical to reliable ground-
fault protection, the Charge Station includes a ground
monitoring circuit to assure presence of a safe electrical
ground.

Self-testing

To assure proper functionality and safety, the Charge
Station includes self-testing and diagnostics circuitry,
which is automatically performed prior to each charging
cycle.
EL -50600-7-2 | REV. B | 20.10.2013