Msi; Enable/Disable Msi; Set Lengths For Msi - Philips Pocket Memo DPM8500 Configuration Manual

MSI

14 MSI

Enable/Disable MSI

Parameter # 0Bh
Enable/Disable MSI
To enable or disable MSI, scan the appropriate bar code below.
Parameter # 0Bh
To enable or disable MSI, scan the appropriate bar code below.
4 - 62 SE655 Decoded Linear Imaging Engine
4 - 62 SE655 Decoded Linear Imaging Engine

Set Lengths for MSI

Set Lengths for MSI
Parameter # L1 = 1Eh L2 = 1Fh
Parameter # L1 = 1Eh L2 = 1Fh
Set Lengths for MSI
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes Parameter # L1 = 1Eh L2 = 1Fh
check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specific range. See
4 - 62 SE655 Decoded Linear Imaging Engine check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specific range. See
Table B-5 on page B-9 for ASCII equivalents. To set lengths via serial commands, see
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes check digits. Lengths for MSI
Table B-5 on page B-9 for ASCII equivalents. To set lengths via serial commands, see
Commands on page A-7.
can be set for any length, one or two discrete lengths, or lengths within a specific range.
Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select MSI - One Discrete Length, then
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
MSI - One Discrete Length, then scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes
Set Lengths for MSI
scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel an incorrect
MSI - One Discrete Length, then scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan
entry, scan Cancel on page 57.
begin on page 4-73. To change the selection or cancel an incorrect entry, scan
Parameter # L1 = 1Eh L2 = 1Fh
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes
check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specific range. See
Table B-5 on page B-9 for ASCII equivalents. To set lengths via serial commands, see
Commands on page A-7.
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select MSI - Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters.
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select MSI - Two Discrete
MSI - One Discrete Length, then scan 1, 4, to decode only MSI symbols containing 14 characters. Numeric bar codes
select MSI - Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters.
Numeric bar codes begin on
Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters. Numeric bar codes begin on page 56. To change the
begin on 4-73. To change the selection or cancel an incorrect entry, scan
page
Numeric bar codes begin on
selection or cancel an incorrect entry, scan Cancel on page 57.
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols
select MSI - Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only MSI symbols containing 6 or 14 characters.
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols containing between 4 and 12
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols
containing between 4 and 12 characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit
Numeric bar codes begin on
characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar
containing between 4 and 12 characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit
numbers must always be preceded by a leading zero). Numeric bar codes begin on
codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
numbers must always be preceded by a leading zero). Numeric bar codes begin on
cancel an incorrect entry, scan
cancel an incorrect entry, scan
Length Within Range - Select this option to decode codes within a specified range. For example, to decode MSI symbols
Any Length - Scan this option to decode MSI Plessey symbols containing any number of characters.
containing between 4 and 12 characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit
numbers must always be preceded by a leading zero). Numeric bar codes begin on Any Length - Scan this option to decode MSI Plessey symbols containing any number of characters.
Barcode scanner configuration guide
Any Length - Scan this option to decode MSI Plessey symbols containing any number of characters.
cancel an incorrect entry, scan
MSI - One Discrete Length
MSI - One Discrete Length
page 4-73. To change the selection or cancel an incorrect entry, scan
page 4-73. To change the selection or cancel an incorrect entry, scan
MSI - One Discrete Length
MSI - Two Discrete Lengths
MSI - Two Discrete Lengths
page 4-73. To change the selection or cancel an incorrect entry, scan
Cancel on page 4-74.
Cancel on page 4-74.
MSI - Two Discrete Lengths
MSI - Length Within Range
MSI - Length Within Range
Cancel on page 4-74.
Enable MSI
(01h)
*Disable MSI
(00h)
Setting Code Lengths Via Serial
Setting Code Lengths Via Serial
Cancel on page 4-74.
Cancel on page 4-74.
Setting Code Lengths Via Serial
Cancel on page
Cancel on page 4-74.
Cancel on page
Cancel on page
4-73. To change the selection or
page
page 4-73. To change the selection or
page 4-73. To change the selection or
4-74.
4-74.
4-74.
51