Interleaved 2 Of; Enable/Disable Interleaved 2 Of 5; Set Lengths For Interleaved 2 Of 5 - Philips Pocket Memo DPM8500 Configuration Manual

Parameter # 06h

Interleaved 2 of 5

To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
8 Interleaved 2 of 5

Enable/Disable Interleaved 2 of 5

Parameter # 06h
Enable/Disable Interleaved 2 of 5
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
Parameter # 06h
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.

Set Lengths for Interleaved 2 of 5

Parameter # L1 = 16h L2 = 17h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
Set Lengths for Interleaved 2 of 5
contains. Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
Set Lengths for Interleaved 2 of 5
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page B-8.
Parameter # L1 = 16h L2 = 17h
Parameter # L1 = 16h L2 = 17h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for I 2 of
5 may be set for any length, one or two discrete lengths, or lengths within a specific range. When setting lengths, single digit numbers must always be preceded by a leading zero.
NOTE
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
NOTE: When setting lengths, single digit numbers must always be preceded by a leading zero.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select I 2
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page B-8.
of 5 One Discrete Length, then scan 1, 4, to decode only I 2 of 5 symbols containing 14 characters. Numeric bar codes
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select I 2 of 5 One Discrete Length,
begin on page 4-73. To change the selection or cancel an incorrect entry, scan
then scan 1, 4, to decode only I 2 of 5 symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel an
When setting lengths, single digit numbers must always be preceded by a leading zero.
NOTE
incorrect entry, scan Cancel on page 57.
4 - 48 SE655 Decoded Linear Imaging Engine
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select I 2
of 5 One Discrete Length, then scan 1, 4, to decode only I 2 of 5 symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan
Set Lengths for Interleaved 2 of 5 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select I 2 of 5 Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only I 2 of 5 symbols containing 6 or 14 characters.
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select I 2 of 5 Two Discrete
Numeric bar codes begin on
Lengths, then scan 0, 6, 1, 4, to decode only I 2 of 5 symbols containing 6 or 14 characters. Numeric bar codes begin on page 56. To change the
selection or cancel an incorrect entry, scan Cancel on page 57.
Length Within Range - Select this option to decode only codes within a specified range. For example, to decode I 2 of 5
symbols containing between 4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single
digit numbers must always be preceded by a leading zero). Numeric bar codes begin on
selection or cancel an incorrect entry, scan
Barcode scanner configuration guide
*Enable Interleaved 2 of 5
*Enable Interleaved 2 of 5
Disable Interleaved 2 of 5
Disable Interleaved 2 of 5
I 2 of 5 - One Discrete Length
page 4-73. To change the selection or cancel an incorrect entry, scan
I 2 of 5 - One Discrete Length
I 2 of 5 - Two Discrete Lengths
Cancel on page
I 2 of 5 - Length Within Range
(01h)
(01h)
(00h)
(00h)
Cancel on page
Cancel on page
4-74.
4-74.
4-74.
Cancel on page
page 4-73. To change the
4-74.
39