Set Lengths For Code - Philips Pocket Memo DPM8500 Configuration Manual

Set Lengths for Code 93

Parameter # L1 = 1Ah L2 = 1Bh
Set Lengths for Code 93
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
Parameter # L1 = 1Ah L2 = 1Bh
contains. Lengths for Code 93 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for Code
set lengths via serial commands, see
93 may be set for any length, one or two discrete lengths, or lengths within a specific range.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select Code 93 One Discrete Length,
Code 93 One Discrete Length, then scan 1, 4, to limit the decoding to only Code 93 symbols containing 14 characters.
4 - 42 SE655 Decoded Linear Imaging Engine
then scan 1, 4, to limit the decoding to only Code 93 symbols containing 14 characters. Numeric bar codes begin on page 56. To change the
Numeric bar codes begin on
4 - 42 SE655 Decoded Linear Imaging Engine
selection or cancel an incorrect entry, scan Cancel on page 57.
4 - 42 SE655 Decoded Linear Imaging Engine
Set Lengths for Code 93 (continued)
Set Lengths for Code 93 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
Set Lengths for Code 93 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select Code 93 Two Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing
select Code 93 Two Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing
2 or 14 characters. Numeric bar codes begin on
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
2 or 14 characters. Numeric bar codes begin on
Cancel on page 4-74.
select Code 93 Two Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing
Cancel on page 4-74.
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select Code 93 Two Discrete
2 or 14 characters. Numeric bar codes begin on
Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing 2 or 14 characters. Numeric bar codes begin on page 56. To
Cancel on page 4-74.
change the selection or cancel an incorrect entry, scan Cancel on page 57.
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to
decode Code 93 symbols containing between 4 and 12 characters, first scan Code 93 Length Within Range, then scan
decode Code 93 symbols containing between 4 and 12 characters, first scan Code 93 Length Within Range, then scan
0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to decode Code 93 symbols containing
0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on
change the selection or cancel an incorrect entry, scan
decode Code 93 symbols containing between 4 and 12 characters, first scan Code 93 Length Within Range, then scan
change the selection or cancel an incorrect entry, scan between 4 and 12 characters, first scan Code 93 Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a
0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on
leading zero). Numeric bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57:
change the selection or cancel an incorrect entry, scan
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Barcode scanner configuration guide
Setting Code Lengths Via Serial Commands on page
4-73. To change the selection or cancel an incorrect entry, scan
page
page
Code 93 - One Discrete Length
page
page
Code 93 - Two Discrete Lengths
Code 93 - Two Discrete Lengths
Code 93 - Two Discrete Lengths
Code 93 - Length Within Range
Code 93 - Length Within Range
Code 93 - Length Within Range
Code 93 - Any Length
Code 93 - Any Length
Code 93 - Any Length
4-73. To change the selection or cancel an incorrect entry, scan
4-73. To change the selection or cancel an incorrect entry, scan
4-73. To change the selection or cancel an incorrect entry, scan
Cancel on page 4-74.
Cancel on page 4-74.
Cancel on page 4-74.
A-7.
Cancel on page 4-74.
page 4-73. To
page 4-73. To
page 4-73. To
35