Bookland Isbn Format; Decode Upc/Ean Supplementals - Philips Pocket Memo DPM8500 Configuration Manual

Parameter # F1h 40h
If Bookland EAN is enabled, select one of the following formats for Bookland data:

Bookland ISBN Format

•
Parameter # F1h 40h
Bookland ISBN-10 - The digital scanner reports Bookland data starting with 978 in traditional 10-digit format with the
If Bookland EAN is enabled, select one of the following formats for Bookland data: special Bookland check digit for backward-compatibility. Data starting with 979 is not considered Bookland in this
mode.
• Bookland ISBN-10 - The digital scanner reports Bookland data starting with 978 in traditional 10-digit format with the special Bookland check digit
for backward-compatibility. Data starting with 979 is not considered Bookland in this mode.
•
Bookland ISBN-13 - The digital scanner reports Bookland data (starting with either 978 or 979) as EAN-13 in 13-digit
• Bookland ISBN-13 - The digital scanner reports Bookland data (starting with either 978 or 979) as EAN-13 in 13-digit format to meet the 2007
format to meet the 2007 ISBN-13 protocol.
ISBN-13 protocol.
•
NOTE: For Bookland EAN to function properly, ensure Bookland EAN is enabled (see Enable/Disable Bookland EAN), then select either Decode
For Bookland EAN to function properly, ensure Bookland EAN is enabled (see
NOTE
UPC/EAN Supplementals, Autodiscriminate UPC/EAN Supplementals, or Enable 978/979 Supplemental Mode in Decode UPC/EAN Supplementals.
EAN on page
Supplementals, or Enable 978/979 Supplemental Mode in

Decode UPC/EAN Supplementals

4-17.
Parameter # 10h
Supplementals are bar codes appended according to specific format conventions (e.g., UPC A+2, UPC E+2, EAN 13+2).
The following options are available:
• If you select Ignore UPC/EAN with Supplementals, and the scanner is presented with a UPC/EAN plus supplemental symbol, the scanner decodes
UPC/EAN and ignores the supplemental characters.
• If you select Decode UPC/EAN with Supplementals, the scanner only decodes UPC/EAN symbols with supplemental characters, and ignores
symbols without supplementals.
• If you select Autodiscriminate UPC/EAN Supplementals, the scanner decodes UPC/EAN symbols with supplemental characters immediately. If
the symbol does not have a supplemental, the scanner must decode the bar code the number of times set via Decode UPC/EAN Supplemental
Redundancy before transmitting its data to confirm that there is no supplemental.
• If you select one of the following Supplemental Mode options, the scanner immediately transmits EAN-13 bar codes starting with that prefix that
have supplemental characters. If the symbol does not have a supplemental, the scanner must decode the bar code the number of times set via
Decode UPC/EAN Supplemental Redundancy before transmitting its data to confirm that there is no supplemental. The scanner transmits UPC/
EAN bar codes that do not have that prefix immediately.
• Enable 378/379 Supplemental Mode.
• Enable 978/979 Supplemental Mode.
» NOTE: If you select 978/979 Supplemental Mode and are scanning Bookland EAN bar codes, see Enable/Disable Bookland EAN to enable
Bookland EAN, and select a format using Bookland ISBN Format.
• Enable 977 Supplemental Mode.
• Enable 414/419/434/439 Supplemental Mode.
• Enable 491 Supplemental Mode.
• Enable Smart Supplemental Mode - applies to EAN-13 bar codes starting with any prefix listed previously.
» NOTE: To minimize the risk of invalid data transmission, select either to decode or ignore supplemental characters.
Barcode scanner configuration guide
*Bookland ISBN-10
Bookland ISBN-13
4-15), then select either Decode UPC/EAN Supplementals, Autodiscriminate UPC/EAN
(00h)
(01h)
Decode UPC/EAN Supplementals on page
Enable/Disable Bookland
11