Subscribe to Our Youtube Channel
Related Manuals for Avalue Technology ECM-PNV
Summary of Contents for Avalue Technology ECM-PNV
-
Page 1: Quick Installation Guide
ECM-PNV (for Rev. C1 – Onboard 18bit LVDS) Intel® Atom™ D525 Dual-Core 3.5” Micro Module with Intel® ICH8-M Chipset Quick Installation Guide Ed – 22 April 2014 Part No. E2017383002R... - Page 2 Disclaimer Avalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Avalue Technology assumes no responsibility or liability for the...
-
Page 3: Technical Support
ECM-PNV Quick Installation Guide Life Support Policy Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL OF Avalue Technology Inc. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for... -
Page 4: Table Of Contents
SATA power connector (S_PWR1) ............22 Audio / USB Daughter Board User’s Guide ..........23 2.4.1 Jumper and Connector Layout .............. 23 2.4.2 Jumper and Connector List ..............23 2.4.3 Setting Jumper and Connector .............. 24 4 ECM-PNV Quick Installation Guide... -
Page 5: Getting Started
Before you begin installing your single board, please make sure that the following materials have been shipped: 1 x 3.5” ECM-PNV Micro Module 1 x Quick Installation Guide for ECM-PNV 1 x AUX-032 daughter board 1 x DVD-ROM contains the followings: ... -
Page 6: Hardware Configuration
ECM-PNV Quick Installation Guide 2. Hardware Configuration 6 ECM-PNV Quick Installation Guide... -
Page 7: Product Overview
ECM-PNV Quick Installation Guide 2.1 Product Overview ECM-PNV Quick Installation Guide 7... -
Page 8: Jumper And Connector List
Serial port 1 pin 9 signal select 3 x 2 header, pitch 2.0 mm JTOUCH_SEL Touch panel mode select 3 x 1 header, pitch 2.54 mm LCD backlight brightness adjustment 3 x 2 header, pitch 2.0mm 8 ECM-PNV Quick Installation Guide... - Page 9 3 x 1 wafer, pitch 2.54 mm S_PWR1 SATA power connector 2 x 1 wafer, pitch 2.0 mm SATA1 Serial ATA connector 1 SATA2 Serial ATA connector 2 RSTBTN Reset button USB1 USB connector Double Deck VGA connector D-sub 15-pin, female ECM-PNV Quick Installation Guide 9...
-
Page 10: Setting Jumpers & Connectors
ECM-PNV Quick Installation Guide 2.3 Setting Jumpers & Connectors 2.3.1 Clear CMOS (JBAT) Protect* Clear CMOS * Default 2.3.2 Serial port 1 pin 9 signal select (JRI1) Ring* +12V * Default 10 ECM-PNV Quick Installation Guide... -
Page 11: Touch Panel Mode Select (Jtouch_Sel)
ECM-PNV Quick Installation Guide 2.3.3 Touch panel mode select (JTOUCH_SEL) 4/ 8W * Default 2.3.4 Miscellaneous setting connector (JFP) Signal PIN PIN Signal PWRBTN# PWRBTN# AUTO_PWR_ON HD_ACT# VCC3 COPEN# * Default ECM-PNV Quick Installation Guide 11... -
Page 12: Lcd Backlight Brightness Adjustment (Jvr)
ECM-PNV Quick Installation Guide 2.3.5 LCD backlight brightness adjustment (JVR) Signal PIN PIN Signal BRIGHT BRIGHT PWM1 *Default 2.3.6 5VSB connector in ATX (PWR_SB) Signal ATX5VSB PSON 12 ECM-PNV Quick Installation Guide... -
Page 13: Signal Description -At/ Atx Mode & Input Power Type
AT Mode (PWR MSEL) Use ATX type power input, and set the board in AT mode. ATX Type (PWR_SB) ATX Mode (PWR MSEL) Use ATX type power input, and set the board in ATX mode. ECM-PNV Quick Installation Guide 13... -
Page 14: Battery Connector (Bat)
ECM-PNV Quick Installation Guide 2.3.7 Battery connector (BAT) Signal 2.3.8 CPU fan connector (CPU_FAN) Signal VCC12 FAN_TAC1 FAN_CTL1 14 ECM-PNV Quick Installation Guide... -
Page 15: Serial Port 2 In Rs-422/485 Mode (J422/485_1)
2.3.9 Serial port 2 in RS-422/485 mode (J422/485_1) J422/485_1 Signal PIN PIN Signal Note: J422/485 is available after modifying the mode of COM2 in BIOS setting. And the wiring must changed to E1701150300R and Connecting it to this J422/485_1 connector. ECM-PNV Quick Installation Guide 15... -
Page 16: Audio Connector (Jaudio)
ECM-PNV Quick Installation Guide 2.3.10 Audio connector (JAUDIO) Signal PIN PIN Signal LINEOUT_R LINEOUT_L LINEIN_R LINEIN_L MIC-R MIC-L FRONT-JD LINE1-JD MIC1-JD 2.3.11 Serial port 2 connector (JCOM2) Signal PIN PIN Signal DCD2 RxDD2 TxDD2 DTR2 DSR2 RTS2 CTS2 16 ECM-PNV Quick Installation Guide... -
Page 17: General Purpose I/O Connector (Jdio)
ECM-PNV Quick Installation Guide 2.3.12 General purpose I/O connector (JDIO) Signal Signal DIO0 DIO10 DIO1 DIO11 DIO2 DIO12 DIO3 DIO13 DIO4 DIO14 DIO5 DIO15 DIO6 DIO16 DIO7 DIO17 SMB_CLK SMB_DATA ECM-PNV Quick Installation Guide 17... -
Page 18: Touch Panel Connector (Jtouch)
5-WIRE 8-WIRE Right Sense Left Sense Bottom Sense Sense Top Sense Right Right Excite Left Left Excite Bottom Bottom Excite Top Excite 2.3.14 SPI connector (JSPI) Signal PIN PIN Signal VSPI SPICE# SPISCK SPISO SPISI 18 ECM-PNV Quick Installation Guide... -
Page 19: Usb Connector (Jusb2/ Jusb3)
ECM-PNV Quick Installation Guide 2.3.15 USB connector (JUSB2/ JUSB3) Signal PIN PIN Signal USBVCC N3/ N7 P3/ P7 P2/ P6 N2/ N6 USBVCC ECM-PNV Quick Installation Guide 19... -
Page 20: Lvds Connector (Jlvds)
ECM-PNV Quick Installation Guide 2.3.16 LVDS connector (JLVDS) Signal PIN PIN Signal VCC3_LVDS VCC_LVDS VCC3_LVDS VCC_LVDS I_SDA I_SCL LVDS_CLK+ LVDS_CLK- LVDS_2+ LVDS_2- LVDS_1+ LVDS_1- LVDS_0+ LVDS_0- 20 ECM-PNV Quick Installation Guide... -
Page 21: Lcd Inverter Connector (Jbkl)
VR signal controlled by JVR. Please see the JVR section for detailed circuitry information. 2.3.17.1 Signal Description – LCD Inverter Connector (JBKL) Signal Signal Description Vadj = 0.75V ~ 4.25V (Recommended: 4.7KΩ, >1/16W) BRIGHT BKL_ON LCD backlight ON/OFF control signal ECM-PNV Quick Installation Guide 21... -
Page 22: Power Connector (Pwr)
ECM-PNV Quick Installation Guide 2.3.18 Power connector (PWR) Signal PIN PIN Signal 2.3.19 SATA power connector (S_PWR1) Signal SATA_PWR Note: SATA_PWR is _+5V for SATA DOM uses 22 ECM-PNV Quick Installation Guide... -
Page 23: Audio / Usb Daughter Board User's Guide
2.54mm USB connector 5 x 2 header, pitch 2.54mm 2.0mm USB connector 5 x 2 header, pitch 2.0mm 2.0mm USB connector 5 x 2 header, pitch 2.0mm TV / Audio connector 8 x 2 header, pitch 2.54mm ECM-PNV Quick Installation Guide 23... -
Page 24: Setting Jumper And Connector
Line out L Line out R SPK L SPK R Line in L Line in R TVGND TVGND COMP 2.0mm USB Connector (JP4) 2.0mm USB Connector (JP5) Signal PIN PIN Signal Signal PIN PIN Signal 24 ECM-PNV Quick Installation Guide...
Need help?
Do you have a question about the ECM-PNV and is the answer not in the manual?
Questions and answers