Table of Contents
Advertisement
Quick Links
The MarinePRO
DI System
™
Reverse Osmosis Water Purification System
(Single and Dual Membrane Models)
INSTALLATION AND OPERATING
MANUAL
WARNING
Please read carefully before proceeding with installation. Failure to
follow any attached instructions or operating parameter may lead to
the product's failure and possible damage to property.
REV 05-05-2009
Advertisement
Table of Contents
Troubleshooting
Related Manuals for SpectraPure MarinePRO DI System
Summary of Contents for SpectraPure MarinePRO DI System
- Page 1 The MarinePRO DI System ™ Reverse Osmosis Water Purification System (Single and Dual Membrane Models) INSTALLATION AND OPERATING MANUAL WARNING Please read carefully before proceeding with installation. Failure to follow any attached instructions or operating parameter may lead to the product’s failure and possible damage to property. REV 05-05-2009...
-
Page 2: Table Of Contents
® SpectraPure TABLE OF CONTENTS Thank You for your purchase of a SpectraPure® System. With proper installation and maintenance, this system will provide you with high quality water for years to come. All SpectraPure® products are rigorously tested by us for safety and reliability. If you have any questions or concerns, please contact our customer service department at 1.800.685.2783 or refer to our... -
Page 3: System Specifications
49 GPD use BPLF-MO-115(-230), more than 49 GPD use BPHF-MO-115(-230). *Operating pressure greater than 80 psi will require a pressure reducing valve. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 4: System Description
® SpectraPure SYSTEM DESCRIPTION: First, the incoming feed water is passed through a 1 micron Micro-Tec™ sediment pre-filter. This filter is required to remove excess turbidity (particulate matter) that may cause the membrane to plug. The second stage of filtration is a1 micron carbon block pre-filter. This filter removes organics and chlorine from the feed water that can damage the membrane. -
Page 5: System Initialization
Liquid Level Controller (LLC-S-115 ), (LLC-M-115) or the Auto Shut-Off Kit (ASOFK). SpectraPure®Inc. assumes no responsibility for water damage due to leaks. It is the user’s responsibility to determine that the system is leak-free. SpectraPure®Inc . -
Page 6: Measuring Waste To Product Water Ratio
System. Failure to perform this procedure can permanently damage the membrane and will void Warranty. In order to maximize the life of your SpectraPure RO Membrane, you may need to adjust the ratio of the concentrate to purified water. If not enough concentrate is allowed to flow past the membrane during operation, the impurities will precipitate out on the membrane surface, clogging the RO Membrane. - Page 7 35.6 38.1 40.6 FR-200 (GREEN) PRODUCT RATE CUT TO LENGTH ml./min. 10.2 12.7 15.2 17.8 20.3 22.9 25.4 27.9 30.5 33.0 35.6 38.1 40.6 SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com...
- Page 8 ® SpectraPure SINGLE MEMBRANE SYSTEM (FIG B) 1/4” BLACK LINE: Tap Water 1/4” BLUE LINE: Product Water 1/4” YELLOW LINE: Waste Water (Flow Restrictor is inside the Waste line) DUAL MEMBRANE SYSTEM (FIG C) SpectraPure®Inc. 480.894.5437 Call us toll-free 1.800.685.2783...
-
Page 9: Flow Restrictor Removal, Adjustment And Replacement
Care should be taken not to crush or otherwise damage the end of the capillary tubing protruding from the end of the insert. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... - Page 10 ® SpectraPure 6. Re-insert the yellow tubing into its push-fitting in the RO membrane as follows: a.) Moisten the O-ring seal inside the concentrate outlet fitting by dripping a few drops of clean water into the fitting. b.) Grasp the yellow tubing near the flow restrictor end, and insert the tubing into the push-fitting.
-
Page 11: Metering & Diagnostics
Test the brine water (yellow line) for chlorine using our chlorine test kit. - Change the DI Cartridge when 70% of the cartridge has changed in color. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 12: Sediment Filter Diagnostic
® SpectraPure SEDIMENT PRE-FILTER REPLACEMENT: A Sediment Filter will usually last approx. 4-6 months, depending on micron rating and quality of water. (The life span of the filter is determined by the turbidity, iron content, organics, and total particulate volume in your water source). -
Page 13: Carbon Filter Diagnostic
NOTE: Do not use filter wrench to tighten housings. Over-tightening will damage housings and void your warranty. Turn on system water supply and check for leaks. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 14: Deionization Cartridge Diagnostic
® SpectraPure DEIONIZATION CARTRIDGE REPLACEMENT: ( right-most housing) The DI stage is the SilicaBuster™ Mixed-Bed Multi-Layer Deionization Cartridge, DI-SB-CI-10. The condition of this cartridge should be judged by observing a change in color. When 70% of the cartridge has changed in color, replace cartridge. -
Page 15: Ro Membrane Diagnostic
For this reason we recommend the use of a conductivity tester in order to receive the most accurate measurement for determining the condition of the RO membrane. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 16: Ro Membrane Replacement
® SpectraPure RO MEMBRANE REPLACEMENT: 1. Turn off the water supply to the RO system. Place the system where the membrane housing is easily accessible. 2. Remove the black tubing from the membrane feed push-fitting by depressing the collar on the fitting with your thumb and pulling the tubing from the push-fitting (Page 9-10). - Page 17 Fig. G: Inserting the New Membrane Element double O- ring end of membrane product water stem tube SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com...
-
Page 18: Troubleshooting Guide
® SpectraPure TROUBLESHOOTING GUIDE FOR RO/DI SYSTEMS: 1. Low production rate: a. Plugged pre-filters. i. Replace pre-filters. b. low water temperature. ii. Heat feed water OR use higher GPD membrane. c. low line pressure. iii. Use booster pump OR use higher GPD membrane. - Page 19 0.661 71.6 /22 0.912 89.6 /32 1.232 55.4 /13 0.684 73.4 /23 0.941 91.4 /33 1.267 57.2/14 0.707 75.2 /24 0.970 93.2 /34 1.304 SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com...
- Page 20 Rejection = [ ( X - Y) ÷ X ] ×100 = 0.953 ×100 = 95.3 Membrane TDS Rejection = 95.3 % : Rejection rates less than 95% may indicate that the membrane should be replaced. * IF YOU NEED HELP WITH THIS PROCEEDURE, PLEASE CONTACT SPECTRAPURE* SpectraPure®Inc. 480.894.5437 Call us toll-free 1.800.685.2783...
-
Page 21: Troubleshooting Guide
SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 22: Tips & Storage
3. Your RO System must be protected from freezing or temperatures above 100° F (38°C). 4. MEMBRANE WARNING: All SpectraPure RO membranes, except for encapsulated membranes, must remain moist at all times. It is the customer’s responsibility to inspect the membrane upon receipt and maintain adequate moisture. -
Page 23: Replacement & Optional Parts
BPHF-MO-115 Hi-Flow Booster Pump, 115V BPHF-MO-230 Hi-Flow Booster Pump, 230V See our Catalog or our Web Site for Liquid Level Controls and other Optional Accessories SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 24: Warranty
SpectraPure (pumps and monitors) carry the original manufacturer’s warranty. SpectraPure, Inc.® warrants the product to the original owner only to be free of defects in material and workmanship for a period of three years from the date of receipt. SpectraPure’s liability under this warranty shall be limited to repairing or replacing at SpectraPure’s option, without charge, F.O.B.
Need help?
Do you have a question about the MarinePRO DI System and is the answer not in the manual?
Questions and answers