Related Manuals for SpectraPure MaxPure MPRO-300 RO System
Summary of Contents for SpectraPure MaxPure MPRO-300 RO System
- Page 1 MaxPure MPRO-300 RO™ System Commercial Grade Reverse Osmosis System (Single Membrane Model Produces 300 Gallons Per Day) INSTALLATION AND OPERATING MANUAL REV 02-27-2009...
-
Page 2: Table Of Contents
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of SpectraPure Inc. SpectraPure®Inc. 480.894.5437 Call us toll-free 1.800.685.2783... -
Page 3: System Specifications
*Operating pressure less than 40 psi will require a high flow booster pump (BPHF-MO-115(230)). *Operating pressure greater than 80 psi will require a pressure reducing valve. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 4: System Description
® SpectraPure SYSTEM DESCRIPTION : The incoming feed water from a cold supply pipe valve is directed through 3/8” BLACK tubing and is first passed through a 1 micron Micro-Tec™ sediment pre-filter. This filter is used to remove excessive turbidity, sand, dust, silt etc.that may cause the carbon filter to plug up. -
Page 5: System Initialization
Rubber Maid™ trash can or set up automatically using a Liquid Level Controllers. (Liquid Level Controllers and Automatic shut off accessories sold separately.) SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 6: Measuring Concentrate To Purified Water Ratio
Failure to perform this procedure can permanently damage the membrane and will void the pro-rated Membrane Warranty. In order to maximize the life of your SpectraPure RO Membrane, you may need to adjust the ratio of the concentrate to purified water. If not enough concentrate is allowed to flow past the membrane during operation, the impurities will precipitate out on the membrane surface, clogging the RO Membrane. -
Page 7: Flow Restrictor Removal, Adjustment, And Replacement
O-ring. Turn off the system water supply and reseat the tubing as described above. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... -
Page 8: System Maintenance Pre-Filter Replacement Proceedure
® SpectraPure Fig. B: Flow Restrictor Assembly capillary tubing yellow tubing plastic insert FILTER REPLACEMENT SEDIMENT PRE-FILTER REPLACEMENT Maintenance Regime: For maximum contaminant removal and long membrane life, the sediment pre-filter must be changed when a 15-20% drop in pressure is observed OR at least 6-month intervals. If your water contains a great deal of sediment the pre-filter may require more frequent changes to maintain adequate production rate and extended membrane life. - Page 9 Screw the housing back onto the assembly, and hand tighten only . Turn on system water supply and check for leaks. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com...
-
Page 10: Ro Membrane Replacement Proceedure
® SpectraPure RO MEMBRANE REPLACEMENT Turn off the water supply to the RO system. Place the system where the membrane housing is easily accessible. Remove the black tubing from the membrane feed push-fitting by depressing the collar on the fitting with your thumb and pulling the tubing from the push-fitting (Page 7). -
Page 11: Testing Quality Of The Membrane
Note: The membrane is rated to produce the rated GPD at 60 psi. For any pres- sure other than 60 psi the output GPD is multipled by the PCF. SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com... - Page 12 ® SpectraPure PCF = Line Pressure (in psi) ÷ 60 Calculation of Temperature Correction Factor (TCF): The output (GPD) also decreases with decrease in temperature. This is because water viscosity increases with decrease in water temperature. Temperature Correction Factor Table (TCF) °F /°C...
- Page 13 Rejection = [ ( X - Y) ÷ X ] ×100 = 0.953 ×100 = 95.3 Membrane Hardness Rejection = 95.3 % : Membrane OK SpectraPure®Inc . Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com...
-
Page 14: Troubleshooting Guide
® SpectraPure TROUBLESHOOTING GUIDE Product Water - Low Production Rate Cause Corrective Action Plugged pre-filters Replace pre-filters Low water temperature Heat feed water or use higher GPD membrane Low feed pressure Use booster pump or use higher GPD membrane Fouled membrane... -
Page 15: Warranty
Effective on products purchased after March 10, 2005. SpectraPure, Inc.® warrants the product to the original owner only to be free of defects in material and workmanship for a period of one year from the date of receipt. SpectraPure’s liability under this warranty shall be limited to repairing or replacing at SpectraPure’s option, without charge, F.O.B. -
Page 16: Replacement Parts Numbers
® SpectraPure REPLACEMENT PARTS Model Replacement Part SF-MT-1-10 1 micron MicroTec™ Sediment Filter CF-5-10 5 micron Carbon Block Pre-Filter CF-1-10 1 micron Carbon Block Pre-Filter MEM-0300 300 gpd TFC Membrane FR-300 Flow Restrictor for 300 gpd System GHA-6-JG Gard Hose Adapter with 3/8in Tubing Push Fitting...
Need help?
Do you have a question about the MaxPure MPRO-300 RO System and is the answer not in the manual?
Questions and answers