Respironics REMstar User Manual page 46

g M
UidanCE and anUfaCtURER
electromagnetic environment specified below. The user of this device should make sure it is used in such an environment.
i t
MMUnity Est
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures,
objects, and people.
a: Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM
and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to
fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the device is
used exceeds the applicable RF compliance level above, the device should be observed to verify normal operation. If abnormal performance is
observed, additional measures may be necessary, such as re-orienting or relocating the device.
b: Over the frequency range 150 kHz to 80 MHz, the field strengths should be less than 3 V/m.
R s
ECoMMEndEd EpaRation
The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer
or the user of this device can help prevent electromagnetic interference by maintaining a minimum distance between portable and
mobile RF communications equipment (transmitters) and this device as recommended below, according to the maximum output
power of the communications equipment.
R M p
atEd axiMUM oWER
o t
UtpUt of RansMittER
(W)
0.01
0.1
1
10
100
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be
estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from
structures, objects, and people.
A-2
' d - E
s EClaRation
iEC 60601 t l C
Est EvEl oMplianCE
3 Vrms 3 Vrms
150 kHz to 80 MHz
3 V/m 3 V/m
80 MHz to 2.5 GHz
d p
istanCEs bEtWEEn oRtablE and
s
EpaRation
150 h 80 Mh
K z to z
d = 1.2
P
0.12
0.38
1.2
3.8
12
i
lECtRoMagnEtiC MMUnity
l E
EvEl lECtRoMagnEtiC
Portable and mobile RF communications equipment should be
used no closer to any part of the device, including cables, than
the recommended separation distance calculated from the
equation applicable to the frequency of the transmitter.
Recommended separation distance:
d = 1.2
P
d = 1.2
P
d = 2.3
P
Where P is the maximum output power rating of the transmitter
in watts (W) according to the transmitter manufacturer and d is
the recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as determined
by an electromagnetic site survey a , should be less than the
compliance level in each frequency range b .
Interference may occur in the vicinity of equipment marked with
the following symbol:
M Rf C
obilE oMMUniCations
d a
istanCE CCoRding to
( )
M
80 Mh 800 Mh
z to
d = 1.2
0.12
0.38
1.2
3.8
12
:
This device is intended for use in the
E
nviRonMEnt
150 kHz to 80 MHz
80 MHz to 800 MHz
800 MHz to 2.5 GHz
E
QUipMEnt and
f t
REQUEnCy of RansMittER
800 Mh
z
d = 2.3
P
REM M s
staR ERiEs
- g
UidanCE
t d :
his EviCE
2.5 gh
z to z
P
0.23
0.73
2.3
7.3
23
U M
sER anUal