Amantii INSERT-26-3825 Safety Information And Installation Manual
  1. Manuals
  2. Brands
  3. Amantii Manuals
  4. Indoor Fireplace
  5. INSERT-26-3825
  6. Safety information and installation manual

Amantii INSERT-26-3825 Safety Information And Installation Manual

Hide thumbs Also See for INSERT-26-3825:
Table of Contents

Advertisement

Quick Links

Download this manual
ELECTRIC FIREPLACES
SAFETY INFORMATION AND INSTALLATION MANUAL
INSERT-26-3825, INSERT-30-4026, INSERT-33-4230
Read these instructions completely before beginning installation. Failure to follow them could cause a heater
malfunction and result in serious injury and/or property damage.
WARNING: All electric heaters have hot and arcing or sparking parts inside. Do not use it in areas where
gasoline, paint or flammable liquids are stored.
WARNING: This heater is tested and listed for use only with the optional accessories listed in these
instructions. Use of optional accessories not specifically tested for this heater could void the heater warranty
and/or result in a safety hazard.
Keep this manual for future reference.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the INSERT-26-3825 and is the answer not in the manual?

Questions and answers

Related Manuals for Amantii INSERT-26-3825

Summary of Contents for Amantii INSERT-26-3825

  • Page 1 ELECTRIC FIREPLACES SAFETY INFORMATION AND INSTALLATION MANUAL INSERT-26-3825, INSERT-30-4026, INSERT-33-4230 Read these instructions completely before beginning installation. Failure to follow them could cause a heater malfunction and result in serious injury and/or property damage. WARNING: All electric heaters have hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are stored.

  • Page 2: Safety Information

    SAFETY INFORMATION Due to high temperatures, the fireplace should be located out of traffic and away from furniture and draperies. Do not place clothing or other flammable material on or near the fireplace. Never place any objects on the fireplace. The fireplace can become very hot when running.

  • Page 3: Listing Approvals

    manufacturer may cause fire, electric shock or injury to persons. 13. Avoid the use of an extension cord because the extension cord may overheat and cause a fire. If you have to use an extension cord, the cord should be No. 14 AWG minimum size and rated not less than 1875 WATTS.

  • Page 4: Product Dimension

    PRODUCT DIMENSION Figure 1 INSERT-26-3825 dimensions Figure 2 INSERT-30-4026 dimensions...

  • Page 5: Locating Fireplace

    Figure 3 INSERT-33-4230 dimensions Locating FIREPLACE WARNING: Never locate this heater where it may fall into a bathtub or any water container. NOTICE: Minimum and maximum clearances must be maintained at all times. Illustrations throughout these instructions reflect typical installations and are for design purposes only. Actual installations may vary slightly due to individual preferences.
  • Page 6 Figure 4 Heater Locations Figure 8 illustrates a variety of ways the heater may be located in a room. The heater may be installed directly on the floor, carpet or raised on a hearth. WARNING: RISK OF FIRE. MAINTAIN ALL SPECIFIED AIR SPACE CLEARANCES TO COMBUSTIBLES.

  • Page 7: Unpacking And Testing Fireplace

    Figure 5 The minimum distance from the top of the appliance that the mantel can be installed is 5cm,at any depth. The sides and back are 1cm. UNPACKING AND TESTING FIREPLACE Carefully remove the unit from the box. Prior to permanently installing the unit, test it to make sure it operates properly.

  • Page 8: Installation

    INSTALLATION CAUTION: The unit's power supply cord must be connected to a properly grounded and protected 120-volt outlet. Always use ground fault protection where required by the electrical code. WARNING - RISK OF FIRE! To prevent a possible fire, do not block the air intake or exhaust in any manner.

  • Page 9: Operating Instructions

    OPERATING INSTRUCTIONS A: REMOTE CONTROL OPERATION The power switch and control panel are located behind the front glass . Power switch located behind glass panel Figure 7 The location of power switch 1. For remote to function make sure the heater is plugged-in and mains power switch located on the up left hand side behind the front glass is at position I.
  • Page 10 Note The heating and flame function can only be operated by the remote control. The remote control needs 2 pcs AA batteries (not included). Note: When the heater is turned on for the first time, it may release a slight, harmless odor. This odor is a normal occurrence caused by the initial heating of the internal heating elements and should not occur after the initial burn off.
  • Page 11 6. To turn off the heater unit completely press the button once. Notice: To work the remote control must be within about 6 metres of the fireplace and not too far off to either side. Important! If the flame does not activate after the POWER ON/OFF button is pressed, press the DISPLAY ON/OFF button to activate the flame.

  • Page 12: Hard-Wire Installation

    HEATER INDICATOR LED RED –1500W HEAT OUTPUT HEATER INDICATOR LED BLUE—750W HEAT OUTPUT HEATER INDICATIOR LED PURPLE—AUTO MODE AUTO MODE Under this mode the heater will automatically turn ON at high heat setting 1500W heat output when the room temperature drops below 22 ℃. When the room temperature is between 22-25℃...

  • Page 13: Cleaning And Maintenance

    A. Unscrew two screw show in the below left figure. Remove the cover and the power cord fix piece, remove power cord. B. Insert external hard wire through the power cord hole and link to the junction box. C. Put the plate back and screw back. CLEANING AND MAINTENANCE WARNING: Always disconnect the power and allow the heater to cool before performing any cleaning, maintenance or relocation.

  • Page 14: Replacement Parts

    REPLACEMENT PARTS REF NO PART NO. DESCRIPTION REMARK FRT60420 HEATER ASSEMBLY REMARK LRC8 CIRCULT BOARD 301506 REMOTE RECEIVER 385506 3W LED ASSEMBLY LED-M1-10 LED STRIP FOR FLAME LED-M-2 LED STRIP FOR FLME LED-M2-10 LED STRIP FOR LOG LED-M3-2 LED STRIP FOR LOG LED-M1-12 LED STRIP FOR EMBER LED-M-12...

  • Page 15: Troubleshooting

    TROUBLE SHOOTING WARNING: Turn off the appliance and let it cool before servicing it. Only a qualified service person should service and repair the heater. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Fireplace turns off and will not Fireplace has overheated and Reset switch by turning main turn on safety device has caused...

This manual is also suitable for:

Insert-30-4026Insert-33-4230

Table of Contents