Omron E5AN Communications Manual page 105

Address
Four- Two- Parameter name
byte byte
mode mode
010E 2107 Alarm Value 2
0110 2108 Alarm Value Upper Limit 2
0112 2109 Alarm Value Lower Limit 2
0404 2402 PV
0406 2403 Internal Set Point (See note 1.)
0408 2404 Multi-SP Monitor
040C 2406 Status (See notes 1 and 2.)
040E 2407 Status (See note 3.)
0410 2408 Status 2 (See notes 1 and 2.)
0412 2409 Status 2 (See notes 1 and 3.)
0420 2410 Decimal Point Monitor
0422 2411 Control Output 1 ON/OFF
Count Monitor
0424 2412 Control Output 2 ON/OFF
Count Monitor
0500 2500 Operation/Adjustment Protect
0502 2501 Initial Setting/Communications
Protect
0504 2502 Setting Change Protect
0506 2503 PF Key Protect
0508 2504 Move to Protect Level
050A 2505 Password to Move to Protect
Level
050C 2506 Parameter Mask Enable
Note 1: Not displayed on the Controller display.
Note 2: In 2-byte mode, the rightmost 16 bits are read.
Note 3: In 2-byte mode, the leftmost 16 bits are read.
6.1 Variable Area (Setting Range) List
Setting (monitor) value
H'FFFFF831 to H'0000270F (−1999 to 9999)
H'FFFFF831 to H'0000270F (−1999 to 9999)
H'FFFFF831 to H'0000270F (−1999 to 9999)
Temperature: Use the specified range for each sensor.
Analog: Scaling lower limit − 5% FS to Scaling upper limit +
5% FS
SP lower limit to SP upper limit
H'00000000 to H'00000003 (0 to 3)
See the 6.2 Status and status 2 for details.
See the 6.2 Status and status 2 for details.
See the 6.2 Status and status 2 for details.
See the 6.2 Status and status 2 for details.
H'00000000 to H'00000003 (0 to 3)
H'00000000 to H'0000270F (0 to 9999)
H'00000000 to H'0000270F (0 to 9999)
H'00000000 (0): No restrictions in operation and adjust-
ment levels
H'00000001 (1): Move to adjustment level is prohibited.
H'00000002 (2): Display and change of only "PV" and
"PV/SP" parameters is allowed.
H'00000003 (3): Display of only "PV" and "PV/SP"
parameters is allowed.
H'00000000 (0): Move to initial setting/communications
setting level is allowed. (Move to
advanced function setting level is dis-
played.)
H'00000001 (1): Move to initial setting/communications
setting level is allowed. (Move to
advanced function setting level is not
displayed.)
H'00000002 (2): Move to initial setting/communications
setting level is prohibited.
H'00000000 (0): OFF (Changing of setup on controller
display is allowed.)
H'00000001 (1): ON (Changing of setup on controller
display is prohibited.)
H'00000000 (0): OFF
H'00000001 (1): ON
H'FFFFF831 to H'0000270F (−1999 to 9999)
H'FFFFF831 to H'0000270F (−1999 to 9999)
(Can only be set. The monitor value is always H'00000000.)
H'00000000 (0): OFF
H'00000001 (1): ON
Level
Operation
Advanced
function
setting
Protect
6-3