Adjusting The Zone 1 Volume; Activating The Zone 1 Front Speakers; Selecting Different Sources For Picture And Sound - JVC RX-8040B Instructions Manual

Selecting different sources for picture and
sound
While watching pictures from a video source (DVD player, VCR, or
DBS tuner), you can listen to sound of an audio source.
• Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
Press one of the audio source selection buttons—PHONO, CD,
TAPE/MD, CDR, FM, AM—while viewing the picture from a
video component such as the VCR or DVD player, etc.
PHONO CD CDR TAPE/MD FM
On the front panel

Adjusting the Zone 1 Volume

On the front panel:
To increase the volume, turn MASTER VOLUME clockwise.
To decrease the volume, turn it counterclockwise.
On the remote control:
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
Notes:
• The volume level can be adjusted within the range of "0" (minimum)
to "70" (maximum).
• If you set "ONE TOUCH OPE" (One Touch Operation) to "ON" (see
page 38), you do not have to adjust the volume level each time you
change the source. It is automatically set to the stored level.
• If you have turned off the receiver with the volume level set at more
than level "30," the volume level will be automatically set at level
"30" next time you turn on the receiver.
CAUTIONS:
• Always set the volume to the minimum before starting any source. If
the volume is set at a high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
• Be careful not to turn up the volume too high when controlling the
receiver without listening to the playback sound. For example, when
adjusting the volume level in Zone 2 from Zone 1.
Activating the Zone 1 Front
Speakers
When shipped from the factory, both pairs of the front speakers have
been set to be used in Zone 1.
• To use the speakers connected to the FRONT2/ZONE2
SPEAKERS terminals, set the speaker usage correctly. (See
"Setting the Zone 2/Speakers 2" on page 38.)
When you have connected two pairs of front speakers and placed
them in Zone 1, you can select which to use.
DVD DVD MULTI PHONO CD
VCR 1 VCR 2 TAPE/MD CDR
AM
TV/DBS VIDEO FM
On the remote
Remote
To use the speakers connected to the FRONT1 SPEAKERS
terminals, press SPEAKERS ON/OFF 1 so that the SPEAKERS 1
indicator lights up on the display.
•
Make sure that the SPEAKERS 2 indicator is not lit.
To use the speakers connected to the FRONT2/ZONE2
SPEAKERS terminals, press SPEAKERS ON/OFF 2/ZONE 2 so
AM
that the SPEAKERS 2 indicator lights up on the display.
•
Make sure that the SPEAKERS 1 indicator is not lit.
To use both sets of the speakers connected to the FRONT1
SPEAKERS and FRONT2/ZONE2 SPEAKERS terminals, press
SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2/ZONE 2 so
that the SPEAKERS 1/2 indicators light up on the display.
ANALOG
L R LINEAR PCM
Ex. When both sets of the speakers selected.
Note:
When you select DVD MULTI as the source or any one of the
Surround/DSP mode which activates the center and/or surround
speaker(s), you can use only one set of the speakers.
To use neither set of the speakers connected to the FRONT1
SPEAKERS and FRONT2/ZONE2 SPEAKERS terminals, press
SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2/ZONE 2 so
that the SPEAKERS 1/2 indicators go off from the display.
• Activating the speakers turns on the Surround and DSP modes
previously selected.
Listening with headphones only:
Connect headphones to the PHONES jack, and deactivate both sets
of the front speakers so that "HEADPHONE" appears and the
HEADPHONE indicator lights up on the display.
•
You can listen to left and right channel sound with headphones.
•
Make sure that all the speaker indicators are not lit.
You can enjoy the sound effects through the headphones when
Surround or DSP mode is activated—3D Headphone
(3D H PHONE) mode.
• "3D H PHONE" appears and the DSP and HEADPHONE indicators
light up on the display. (For details, see pages 47 and 48.)
Note:
3D Headphone (3D H PHONE) mode is not valid for DVD MULTI
playback mode.
CAUTION:
NOT
Be sure to turn down the volume:
• Before connecting or putting on headphones, as its high volume can
damage both the headphones and your hearing.
• Before turning on the speakers again, as its high volume may come
out of the speakers.
SPEAKERS 1 2
VOLUME
ZONE 1
21