Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ledj Eco LED 64
Summary of Contents for Ledj Eco LED 64
-
Page 1: User Manual
Eco LED 64 (order code: LEDJ32) USER MANUAL... -
Page 2: Safety Instructions
LEDJ Eco LED 64 SAFETY WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! CAUTION! Keep this equipment away from rain, moisture and liquids. SAFETY INSTRUCTIONS Every person involved with the installation, operation & maintenance of this... -
Page 3: Operating Determinations
LEDJ Eco LED 64 SAFETY IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment. • Never let the power-cable come into contact with other cables. Handle the power-cable and all mains voltage connections with particular caution! •... -
Page 4: Control Features
LEDJ Eco LED 64 INTRODUCTION Introduction CONTROL FEATURES • 6 channel DMX-512 Eco LED 64 Can • Static/Dimmer/Strobe • Individual control of Red, Green and Blue LEDs Features • 177 LEDs: - Red (60), Green (60), and Blue (57) • Ultra Bright 10mm LEDs •... - Page 5 LEDJ Eco LED 64 OVERVIEW Product Overview Identificaion: 1) DMX in 2) DMX out 3) Fuse 4) Sensitivity control 5) Dip switches Setup Operating Instructions The Eco LED-64 is a DMX-512 controllable, full RGB colour mixing Par Can made up of high efficiency and super bright LED’s.
- Page 6 Note: You can have any combination of switches 6, 7 and 8 to obtain any static colour mix. Sound Activation The Eco LED 64 Can has a built-in microphone which enables it to operate in Sound to Light mode. Set the sensitivity control to the desired level, and the Eco LED 64 Can will change colour to the beat of the music.
-
Page 7: Control Options
In this mode you will be able to control each individual trait of the fixture and each fixture independently. The Eco LED 64 uses 6 channels of control. Enable the DMX control by setting dip switch No: 10 to the ON position. Use dip switches 1 – 9 to address each fixture accordingly. - Page 8 LEDJ Eco LED 64 CONTROL OPTIONS Set the start address using the group of dip switches located usually on the back of the fixture. Each dip switch has an associated value. Adding the value of each switch in the ON position will provide the start address.
- Page 9 DATA Cable (DMX cable) requirements (for DMX operation): • The Eco LED 64 can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output (figure 1).
- Page 10 LEDJ Eco LED 64 DMX SET UP Notice: • Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing.
- Page 11 LEDJ Eco LED 64 DIP SWITCH REFERENCE CHART DMX Dip Switch Quick Reference Chart Dip Switch Position...
- Page 12 LEDJ Eco LED 64 DMX VALUES DMX Channel Values No Function Technical Specifications Weight & Dimensions • Length…............300mm • Width..............270mm • Height……………………………………………..235mm • Weight………………………………………..2.2kgs Power • AC input……………………………………..240V/50hz Fuse • Main……………………………………………….20mm Glass 1A Fast Blow Control & Programming • Data input………………………………………...Locking 3-pin XLR male socket •...
Need help?
Do you have a question about the Eco LED 64 and is the answer not in the manual?
Questions and answers