Operating Jvc's Audio/Video Components - JVC RX-1024VBK Instructions Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control
signals for JVC components are preset in the remote control.
IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU LINK-3
(SYNCHRO) jacks (see page 48) in addition to the connections using cables
with RCA pin plugs (see page 8) or using digital cables (see page 11).
• Aim the remote control directly at the remote sensor on the receiver.
Tuner
After pressing FM or AM (with the remote control mode
selector set to "AUDIO/TV/VCR"), you can perform the
following operations:
FM: Selects an FM broadcast.
AM: Selects an AM broadcast.
1 — 10, +10: Selects a preset channel number directly.
For channel number 5, press 5. For
channel number 15, press +10, then 5.
For channel number 20, press +10, then
10.
TUNING UP/TUNING DOWN:
Tunes into stations.
FM MODE/MUTE: Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations (with the
remote control mode selector set to "AUDIO/TV/VCR"):
SURROUND MODE: Changes the DSP modes.
After pressing SOUND (with the remote control mode selector
set to "AUDIO/TV/VCR"), you can perform the following
operations:
SEA MODE: Changes the SEA modes.
SUBWOOFER +/–: Adjusts the subwoofer output level.
CNTR +/–: Adjusts the center speaker output
level.
REAR•L +/–: Adjusts the left rear speaker output
level.
REAR•R +/–: Adjusts the right rear speaker output level.
EFFECT: Selects the effect level.
TEST: Turns on or off the test tone output.
CNTR TONE: Selects the center tone.
CD player
After pressing CD (with the remote control mode selector set to "AUDIO/TV/VCR"),
you can perform the following operations on a CD player:
PLAY: Starts playing.
4 4
4 4 4 :
Returns to the beginning of the current (or previous) track.
¢ : ¢ ¢
¢ ¢
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
1 — 10, +10: Selects a track number directly.
For track number 5, press 5. For track number 15, press +10, then 5. For
track number 20, press +10, then 10. For track number 30, press +10,
+10, then 10.
TV/CATV/
DBS VCR 1 AUDIO
POWER POWER POWER
DVD VCR 1 VCR 2 VIDEO
CD TAPE/MD PHONO TV/DBS
AM FM SLEEP
– +
CNTR TONE CNTR
SURROUND
1 2 3
MENU
MODE
DIGITAL/
TEST – REAR · L +
ANALOG
4 5 6
INPUT ENTER
– +
EFFECT REAR · R
7 8 9
SOUND /P
– +
SEA MODE SUBWOOFER
10 0 +10
DISC
100+
RETURN FM MODE/
MUTE
AUDIO/
TV/VCR
+
–
CHANNEL
CATV
DBS
+
–
VOLUME
MUTE
ON SCREEN CONTROL
MENU
SET EXIT
VCR1 TAPE
CONTROL
/REW PLAY FF/
DOWN TUNING UP
REC
TV/VIDEO STOP PAUSE
LIGHT
RM-SR1024U REMOTE CONTROL
Notes:
• If you use the buttons on the
front panel or the menu
function to choose a source,
the remote control will not
operate that source. To
operate a source with the
remote control, the source
must be selected using
buttons on the remote control.
• Check to see if its remote
control mode selector is set to
the correct position. To
operate audio system, TVs,
and VCRs, set it to "AUDIO/
TV/VCR."
• Refer also to the manuals
supplied with your
components.
Note:
After adjusting sounds, press
the corresponding source
selecting button or DISC to
operate your target source by
using 10 keys; otherwise, 10
keys cannot be used for
operating your target source.
58